Nortel Networks Telephone Accessories M7100N User Manual

Enterprise Edge  
M7100N  
User Card  
© 2000 Nortel Networks  
P0908517 Issue 02  
 
Your Enterprise Edge M7100N telephone  
Display  
shows the time, date, and call information; guides you while  
using features; tilts for easy viewing  
Release button  
cancels active calls  
Feature button  
starts or ends a feature  
Hold button  
Dial pad  
Volume control  
Memory button  
is programmable to store a  
feature or to automatically  
dial an internal or external  
number.  
Using Button  
Inquiry  
Check what is programmed on your memory button.  
1. Release all calls or lines with dial tone.  
2. Press ƒ•‚.  
3. Press the button that you want to check.  
4. Read the display.  
5. Press ƒ when finished.  
Adjusting the  
1. Press ƒ•‡.  
display contrast  
2. Press to · for the level you want; the higher the number the higher  
the level.  
Selecting a ring  
type and volume  
level  
1. Press ƒ•fl.  
2. Press , ¤, or to hear the different ring types.  
3. While the telephone is ringing, press to adjust the  
volume level.  
4. Press ƒ to store the ring.  
Adjusting the  
handset or  
1. Press when using the handset or the speaker.  
telephone  
speaker volume  
Page 1 Enterprise Edge M7100N User Card  
 
Making and answering calls  
Answering calls  
1. When your telephone rings, lift your handset.  
You are immediately connected to the call.  
Making external  
calls  
Depending upon the dialling mode programmed for your telephone, you  
may be able to dial your call before lifting your handset.  
1. Pick up the handset.  
9
2. Dial (your system’s exchange line access code or a line pool  
access code).  
3. Dial the external telephone number.  
Making internal  
calls  
1. Pick up the handset.  
2. Dial the internal number.  
Note: Extension numbers and the exchange line access code are  
supplied by your System Administrator.  
Making or  
The M7100N telephone allows you to have two calls active at the same  
answering a  
second call  
time.  
You can switch between calls using ˙.  
To answer a second call while on another call  
1. Press ˙ to put the first call on hold.  
The second call automatically comes onto the line.  
To hold a call and make a second call  
1. Press ˙ to put the first call on hold.  
2. Dial the telephone number for the second call.  
To return to the first call  
1. Press ˙ again to return to the first call on hold.  
The second call is automatically put on hold.  
˙
To hold a call  
1. Press ˙.  
2. Press ˙ again to return to the call on hold.  
Check the display for confirmation or additional information.  
Note: If you have difficulty selecting a line on your M7100N telephone,  
ask your System Administrator to check your telephone's  
programming. Your telephone must be assigned to use an  
exchange line or line pool.  
Page 2 Enterprise Edge M7100N User Card  
 
Programming the memory button  
About the  
memory button  
The memory button can store a  
telephone number or feature  
code to give you one touch  
dialling or feature activation. You  
can change the memory button  
by programming it with a new  
number or feature code.  
Memory button  
Remember: Press ƒ•‚ to check a memory or line button.  
Programming the  
memory button  
External Autodial  
1. If you are on a call or a line with dial tone, press ˙ or®.  
2. Press ƒ•⁄.  
3. Dial the external number.  
4. Press ˙ to store the number.  
5. Label your new button.  
Internal Autodial  
1. If you are on a call or a line with dial tone, press ˙ or®.  
2. Press ƒ•¤.  
3. Dial the extension number.  
4. Label your new button.  
Features  
1. If you are on a call or a line with dial tone, press ˙ or ®.  
2. Press ƒ•‹.  
3. Press ƒ and the feature code.  
4. Label your new button.  
Erasing the memory button  
1. If you are on a call or a line with dial tone, press ˙ or®.  
2. Press ƒ•⁄.  
3. Press ˙ to erase the button.  
Notice  
These telephones now conform to the latest standards in relation to the  
positioning of Q and Z on the number buttons. The Q appears on button  
number 7 and the Z appears on button number 9.  
Page 3 Enterprise Edge M7100N User Card  
 
Setting up the telephone  
ATTENTION Before attempting to carry  
out any work on the telephone, ensure  
that the line cord is unplugged from the  
wall socket.  
Connecting the cords  
1
2
Press here firmly  
until it clicks, to  
attach the stand.  
To remove any of the cords, squeeze  
the release latch on the plug and gently  
pull the plug from the socket.  
Connect the handset cord to the jack  
labelled with the telephone icon and  
route the cord as shown.  
Route the line cord through the stand  
and connect the cord to the telephone  
jack that is marked with the jack icon.  
Attach the stand using either pair of  
slots; to raise the back of the telephone  
to its highest position, use these slots.  
Press here to  
remove the stand.  
Once the above work is complete, plug  
the line cord back into its wall socket.  
Page 4 Enterprise Edge M7100N User Card  
 
Setting up the telephone  
Mounting the  
telephone on  
the wall  
12 cm  
Page 5 Enterprise Edge M7100N User Card  
P0908517 Issue 02  
 

Miller Electric Air Compressor AC Generator Air Compressor User Manual
MSi Laptop X600 096US User Manual
MTD Backyard Playset A06 User Manual
Multi Tech Systems Network Card TBR21 User Manual
NordicTrack Treadmill NTTL09994 User Manual
Omron Blood Pressure Monitor M4 I User Manual
Oster Blender 6640 User Manual
Panasonic Answering Machine KX T1720 User Manual
Panasonic IP Phone KX T7050 User Manual
Partner Tech Lawn Mower P145107 User Manual