Patton electronic Switch 4654 Series User Manual

SmartNode 4654 and 4658 Series

ADSL2+ Multiport ISDN VoIP IAD

Quick Start Guide

Important—This is a Class A device and is intended for use in a light industrial environment. It is not

intended nor approved for use in an industrial or residential environment.

Approval—This device is approved for connection to the public ISDN telecommunication network,

over BRI/S0-ISDN interfaces.

Zulassung—Zugelassen für die Anschaltung an das öffentliche ISDN Telekommunikationnetz an

BRI/S0-ISDN Schnittstellen.

Aprobación—Este aparato está aprobado para conexión a red publica ISDN sobre interfaz BRI/S0.

Approbation—Cet appareil est approuve pour la connexion au reseau ISDN public avec les interfaces

BRI/S0.

Document Number: 13225U7-002 Rev. A

Part Number: 07MSN4650A-QS

Revised: June 12, 2008

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

–

Straight-through wired cable

LAN (ETH 0/0)

Laptop PC

Figure 1. Connecting to the PC

1. Connect the PC’s Ethernet port to LAN (ETH 0/0) port of the SmartNode 4650 ADSL2+. The SmartNode

4650 ADSL2+ Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through Ethernet

cables for host or hub/switch connections. (See ﬁgure 1.)

2. The SmartNode comes with a built-in DHCP server to simplify conﬁguration. Therefore, to automatically

conﬁgure the PC for IP connectivity to the SmartNode, conﬁgure the laptop PC for DHCP. The SmartNode

will provide the PC with an IP address.

3. Check the connection to the SmartNode by executing the ping command from the PC command window

as follows:

ping 192.168.1.1

3.0 Conﬁguring the desired IP address

3.1 Factory-default IP settings

The factory default conﬁguration for the Ethernet interface IP addresses and netmasks are listed in table 1.

Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default DHCP

server. The WAN interface uses DHCP client to get the IP address and netmask automatically from the

service provider.

Table 1. Factory default IP address and network mask conﬁguration

Item

IP Addresss

Network Mask

DHCP

WAN interface DSL port (DSL 0/0)

LAN interface Ethernet 1 (ETH 0/0)

DHCP server address range (LAN)

DHCP

192.168.1.1

255.255.255.0

192.168.1.10-192.168.1.19

If these addresses match with those of your network, go to section 4.0 “Connecting the SmartNode to the

network” on page 4. Otherwise, continue with the following sections to change the addresses and

network masks.

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

3.2 Login

1. To access the SmartNode, start the Telnet application on your PC. Type the default IP address into the

address ﬁeld: 192.168.1.1. Accessing your SmartNode via a Telnet session displays the login screen.

Type the factory default login: administrator and leave the password empty. Press the Enter key after the

password prompt.

password:<Enter>

192.168.1.1>

2. After you log in, your SmartNode will be running in operator execution mode (indicated by > character

in the command line prompt). To enter conﬁguration mode, use the commands enable and conﬁgure.

192.168.1.1>enable

192.168.1.1#configure

192.168.1.1(cfg)#

3.3 Changing the WAN IP address

1. To modify IP conﬁguration settings, you must enter context IP mode. Enter the following command:

192.168.1.1(cfg)#context ip router

192.168.1.1(ctx-ip)[router]#

2. Now you can set your IP address and network mask for the interface ETH 0/0(WAN). In this example a

network 172.16.1.0/24 is assumed. The IP address in example is set to 172.16.1.99. (You should set it

to the IP address that the network provider has given you.)

Note The examples in this guide use a private IP network with the network address 172.16.1.0/24.

192.168.1.1(ctx-ip)[router]#interface eth_dsl

192.168.1.1(if-ip)[eth_dsl]#ipaddress 172.16.1.99 255.255.255.0

2002-10-29T00:09:40 : LOGINFO

172.16.1.99(if-ip)[eth_dsl]#

: Link down on interface eth0.

: Link up on interface eth0.

3. Copy this modiﬁed conﬁguration to your new start-up conﬁguration. This will store your changes in non-

volatile memory. On the next start-up the system will initialize itself using the modiﬁed conﬁguration.

172.16.1.99 (if-ip)[eth_dsl]#copy running-config startup-config

172.16.1.99 (if-ip)[eth_dsl]#

The SmartNode can now be connected to your network.

4.0 Connecting the SmartNode to the network

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

CAUTION

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

In general, the SmartNode will connect to the network via the WAN (DSL) port. This enables the SmartNode to

offer routing services to the PC hosts on LAN (ETH 0/)) port. The SmartNode 4650 ADSL2+ Series provides an

auto-MDX feature for both Ethernet ports, so you can use a straight-through or cross-over cable to connect to a

host or a switch (see ﬁgure 2).

12V

1.25A

LAN

Straight-through wired

or crossover cable

LAN (ETH 0/0)

Network

WAN (DSL)

Figure 2. Connecting the SmartNode to the network

1. You can check the connection with the ping command from the SmartNode to another host on the

local LAN.

172.16.1.99(if-ip)[eth_dsl]#ping <IP Address of the host>

Note If the WAN address is not set to DHCP, to ping a device outside your local LAN you must ﬁrst conﬁgure

the default gateway. (For information on conﬁguring the default gateway, refer to section “Set IP

addresses” in Appendix C, “Command Summary” of the SmartNode Series SmartWare Software Conﬁg-

uration Guide.)

5.0 Loading the conﬁguration (optional)

Patton provides a collection of conﬁguration templates on the CD-ROM shipped with your SmartNode device—

and also on the support page at www .patton.com/voip—one of which may be similar enough to your

application that you can use it to speed up conﬁguring the SmartNode. Simply download the conﬁguration note

that matches your application to your PC. Adapt the conﬁguration as described in the conﬁguration note to your

network (remember to modify the IP address) and copy the modiﬁed conﬁguration to a TFTP server. The Smart-

Node can now load its conﬁguration from this server.

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

Note Patton regularly adds new conﬁguration templates to the collection at www.patton.com/voip, so if

you do not see your application on the CD-ROM, it may have been added to the website.

Note If your application is unique and not covered by any of Patton’s conﬁguration templates, you can man-

ually conﬁgure the SmartNode instead of loading a conﬁguration ﬁle template. In that case, refer to

the SmartNode Series SmartWare Software Conﬁguration Guide for information on conﬁguring the Smart-

Node device.

In this example we assume an TFTP server resides on the host with the IP address 172.16.1.11 and the conﬁgu-

ration ﬁle named SN.cfg resides in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-

config

Download...100%

172.16.1.99(if-ip)[eth0]#

After you reboot the SmartNode the new startup conﬁguration will become active.

When you issue the reload command, the SmartNode will ask if you want to copy the

running conﬁguration to the startup conﬁguration. Since you just downloaded a con-

ﬁguration ﬁle to the startup conﬁguration you must answer this question with NO.

Otherwise, the downloaded conﬁguration will be overwritten and lost!

IMPORTANT

172.16.1.99(if-ip)[eth0]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'?

Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes

The system is going down

6.0 Additional Information

Refer to the SmartNode Series SmartWare Software Conﬁguration Guide and the SmartNode Getting Started Guide

located on the CD-ROM shipped with your SmartNode device and available online at www.patton.com/

manuals. For detailed information about:

• Installing, conﬁguring, operating, and troubleshooting.

• Warranty, trademark & compliance

The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.

A.0 Customer and Technical Support

Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP client

Online support: www.patton.com

E-mail support: [email protected]—answered within 1 business day

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

Telephone support:

• Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

• Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

Safety Compliance:

• UL60950-1/CSA C22.2 No. 60950-1

• IEC/EN 60950-1

• AS/NZS 60950-1

PSTN Regulatory Compliance:

• TBR3

• AS/ACIF S031

• AS/ACIF S043 (ADSL card)

B.2 Radio and TV interference

The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that

is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television

reception. The SmartNode router have been tested and found to comply with the limits for a Class A computing

device in accordance with speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide rea-

sonable protection from such interference in a commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the SmartNode router does cause interference to radio or

television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct

the interference by one or more of the following measures: moving the computing equipment away from the

receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet

(such that the computing equipment and receiver are on different branches).

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

B.3 ISDN compliance

This device is approved for connection to the public ISDN telecommunication network.

When this device is used in North America, it shall be connected to a Network Termina-

tion Device and not connected directly to an outside POTS line.

CAUTION

B.4 CE Declaration of Conformity

Product Description: SmartNode 4650 ADSL2+ Series

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws

of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition

of their conformity.

The safety advice in the documentation accompanying the products shall be obeyed.

The conformity to the above directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded from www.patton.com/certiﬁcations/.

B.5 EG-Konformitätserklärung

Produktbezeichnung: SmartNode 4650 Sendereihe

Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol-

gender Richtlinie überein:

R&TTE 1999/5/EG

Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der Mitglied-

staaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige Anerkennung ihrer

Konformität.

Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.

Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem

Gerät bestätigt.

Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/

certiﬁcations/.

B.6 Zulassung

Zugelassen fur die Anschaltung an das öffentliche ISDN Telekommunikationnetz an BRI/S0-ISDN Schnittstellen.

B.7 Authorized European Representative

D R M Green, European Compliance Services Limited.

Oakdene House, Oak Road , Watchﬁeld, Swindon, Wilts SN6 8TD, UK

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu-

ment are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the Models SN4650 Series Getting Started Guide

located on the CD-ROM that came with your VoIP Gateway Router or available online at www.patton.com.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

Notes

____________________________________________________________________

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

Notes

____________________________________________________________________

Notes

____________________________________________________________________

SmartNode 4654 & 4658 ADSL2+ Quick Start Guide

Peavey Music Mixer AMD 1220 User Manual
Perreaux Power Supply SP100A User Manual
Philips Bottle Warmer SCF660 User Manual
Philips Computer Monitor 107X4 User Manual
Philips Fan HD 3274 75 User Manual
Philips Flat Panel Television 14PF7846 User Manual
Philips Power Supply LR14PB2C User Manual
Polaroid MP3 Player PMP283C 4 User Manual
Poulan Chainsaw Chainsaw User Manual
Powermatic Sander WB 25 User Manual