Peerless Industries TV Mount PLA 60 User Manual

Models: PLA 60, PLA 60-S,  
PLAV 60, PLAV 60-S  
Installation and Assembly - Articulating Swivel Arm for  
37" - 60" Plasma Screens  
This product is UL Listed. It must be  
installed by a qualified professional  
installer.  
R
Maximum UL Load Capacity: 175 lb (79 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06  
 
Before you start make sure all parts  
listed are included with your product.  
D M  
Parts List  
PLA 60  
QTY. PART #  
PLA 60-S  
PART #  
PLAV 60  
PART #  
PLAV 60-S  
PART #  
DESCRIPTION  
A wallplate  
1
201-1040  
201-4040  
201-1040  
201-4040  
B tilt-roll assembly  
1
1
1
3
8
1
1
1
2
1
8
1
1
8
8
1
4
4
1
1
201-1093  
201-1072  
201-1041  
600-1012  
520-9262  
540-1074  
560-0108  
520-1315  
540-1070  
520-1210  
590-1123  
580-1166  
590-1007  
520-1243  
540-1063  
560-9728  
590-1166  
590-1168  
600-1015  
560-9716  
201-4093  
201-4072  
201-1041  
600-1012  
520-9262  
540-1074  
560-0108  
520-1315  
540-1070  
520-1210  
590-1123  
580-1166  
590-1007  
520-1243  
540-1063  
560-9728  
590-1166  
590-1168  
600-1015  
560-9716  
201-1048  
201-1049  
201-1041  
600-1012  
520-9262  
540-1074  
560-0108  
520-1315  
540-1070  
520-1210  
590-1123  
580-1166  
590-1007  
520-1243  
540-1063  
560-9728  
590-1166  
590-1168  
600-1015  
560-9716  
201-4048  
201-4049  
201-1041  
600-1012  
520-9262  
540-1074  
560-0108  
520-1315  
540-1070  
520-1210  
590-1123  
580-1166  
590-1007  
520-1243  
540-1063  
560-9728  
590-1166  
590-1168  
600-1015  
560-9716  
E
F
C arm assembly  
D wall support arm axle  
E vinyltrim  
F M10 x 1.5 x 15 mm screw bolt  
G .505 x .75 x .062" nylon washer  
H tilt adjustment knob  
I carriage bolt 3/8"-16 x 3.25"  
J 1.525 x 2 x .062" delrin washer  
K #8-32 x .375" socket head cap screw  
L plastic finishing cap  
M holdingpin  
G
H
K
N
N retainerplug  
O 5/16 x 3" wood screw  
P .250 x 1 x .068" washer  
Q 9/64"allenwrench  
R cable management clips  
S cable tie  
T 36" polyester mesh sleeve  
U 6 mm allen wrench  
V 10 mm allen wrench  
W anchor  
1
8
n/a  
590-1025  
n/a  
590-1025  
560-9727  
590-1025  
560-9727  
590-1025  
L
A
C
J
R
P
B
T
W
V
U
I
Q
O
S
Some parts may appear slightly different than illustrated.  
3 of 9  
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06  
 
Installation to Wood Stud Wall  
WARNING  
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached  
hardware and components.  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal  
studs (contact customer care). Metal stud installation is not UL evaluated.  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is  
highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers  
are responsible to provide hardware for other types of mounting situations.  
• Never exceed the Maximum UL Load Capacity of 175 lb (79 kg).  
Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the  
1
studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line  
down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .36"  
above the desired screen center for PLA 60 and PLA60-S and .43" below the desired screen center for PLAV 60  
and PLAV 60-S. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting  
holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level,  
secure it using eight 5/16 x 3" wood screws (O) and washers (P).  
Skip to step 2 on page 6.  
WARNING  
• Never mount this product to metal studs without the  
required accessory.  
P
O
A
ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06  
4 of 9  
 
Installation to Concrete Wall  
WARNING  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached  
hardware and components.  
• Never exceed the Maximum UL Load Capacity of 175 lb (79 kg).  
• Never mount this product to metal studs.  
IMPORTANT! Concrete must be 2000 psi density  
minimum.  
concrete  
surface  
1
Use wall plate (A), making sure that it is level, as a  
template to mark holes. The top mounting slots should  
be located .36" above the desired screen center for PLA  
60 and PLA 60-S and .43" below the desired screen  
center for PLAV 60 and PLAV 60-S. Use the masonry bit  
to drill 5/16" (8 mm) dia. holes to a minimum depth of 3"  
(76 mm). Insert anchors in holes flush with wall as shown  
(right). Place wall plate (A) over anchors (W) and secure  
with 5/16 x 3" wood screws (O) and washers (P).  
1
W
Drill hole(s) and insert anchor(s) (W)  
mounting  
plate  
2
WARNING  
W
• Tighten wood screws so that wall plate is firmly  
attached, but do not overtighten. Overtightening can  
damage screws, greatly reducing their holding power.  
Place plate over anchor(s) (W) and secure with screw(s)(O)  
3
• Never tighten in excess of 80 in • lb (9 N.M.).  
Tighten all fasteners  
WARNING  
• Always attach concrete expansion anchors directly to  
load-bearing concrete.  
• Never attach concrete expansion anchors to concrete  
covered with plaster, drywall, or other finishing mate-  
rial. If mounting to concrete surfaces covered with a  
finishing surface is unavoidable, the finishing surface  
must be counterbored as shown below. If plaster/  
drywall is thicker than 5/8", custom fasteners must be  
supplied by installer (Not evaluated by UL).  
W
P
O
CORRECT  
INCORRECT  
mounting  
plate  
concrete  
concrete  
mounting  
plate  
A
plaster/  
drywall  
plaster/  
drywall  
5 of 9  
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06  
 
WARNING  
• If you are uncertain that product is properly installed, call customer care.  
Note: There are five mounting positions. The  
N
J
D
2
center position is shown (right). Slide washer (J)  
over wall support arm axle (D). Next, insert plastic  
cap (N) into axle. Then, insert holding pin (M) into  
axle. See detail 1.  
M
Place arm assembly (C) with washer (J) into wall  
plate (A). Insert axle assembly shown in detail 1  
through wall plate (A), arm assembly (C), and  
washer (J). Lock axle in place by aligning holding  
pin (M) with notches shown in detail 2.  
2-1  
2-2  
DETAIL 1  
A
J
Insert socket cap screw (K) into hole at bottom of  
wall support arm axle (D) as shown in detail 3.  
Tighten screw using 9/64" allen wrench (Q).  
NOTCH  
C
DETAIL 2  
Note: Fit of axle (D) into wall plate (A) and arm  
assembly (C) will be tight. Gently tap into place  
with a hammer if necessary.  
K
D
DETAIL 3  
Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown. Cable ties (S) are used  
with clips for cord management.  
3
Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.  
3-1  
T
R
C
S
ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06  
6 of 9  
 
Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm  
assembly (C).  
4
Insert one finishing cap (L) into each unused hole of wall plate (A).  
4-1  
L
A
SWIVEL BOX  
C
E
Note: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding  
with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard race. It is  
not used with this product.  
Insert and tape carriage bolt (I) into top hole of pitch-roll assembly (B). Attach tilt-roll assembly to adapter  
bracket with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).  
5
Note: Adapter bracket (not UL evaluated, sold separately) will vary in size and style.  
CAUTION  
GENERIC  
ADAPTER BRACKET  
• Do not overtighten screws! Overtightening may hinder  
roll option.  
I
B
F
7 of 9  
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06  
 
WARNING  
• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.  
Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed  
thread.  
6
SWIVEL BOX  
C
.25"  
F
Hook tilt-roll assembly (B) onto M10 screws (F).  
Insert carriage bolt (I) into slot of swivel box as  
shown in figure 6.1. Install nylon washer (G) and tilt  
adjustment knob (H).  
6-1  
6-2  
CAUTION  
• After tilt is adjusted, all fasteners must be tightened.  
Failure to do so will result in damage to the mount.  
Install remaining two M10 screws (F) as shown in  
figure 6.2. HAND TIGHTEN all four M10 screws to  
allow for tilt adjustment. Remove tape from carriage  
bolt (I). For tilt adjustment, push back on the top of  
plasma to relieve pressure on knob. Adjust tilt to  
desired position and tighten tilt adjustment knob (H),  
then securely tighten all four M10 screws (F) using 6  
mm allen wrench (U).  
H
I
H
G
SWIVEL BOX  
I
F
F
B
fig 6.1  
fig 6.2  
ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06  
8 of 9  
 
Depending on the specific size & weight of the plasma,  
articulating swing arm may be angled at different  
positions, causing plasma to appear to lean sideways  
at different articulating positions. Tilt-roll assembly (B)  
allows plasma to be manually adjusted, so plasma can  
be horizontal at all positions. To adjust, gently rotate  
plasma by hand to desired position.  
If it is too difficult to adjust roll of plasma, loosen  
screws shown in figure 7.1 using a phillips screw-  
driver.  
7-1  
7
IMPORTANT! Do not loosen or tighten screws  
more than 1/8 turn.  
ARTICULATING ARM  
PLASMA  
ROLL  
ADJUSTMENT  
SCREWS  
FOR PLAV 60 ONLY:  
Position of screen may be adjusted vertically up to  
.79" in each direction by doing the following:  
To lower screen, turn socket screw shown in figure  
8.1 clockwise with 10 mm allen wrench (V).  
8
To raise screen, turn socket screw shown in figure  
8.1 counterclockwise with 10 mm allen wrench (V).  
fig 7.1  
SOCKET  
SCREW  
fig 8.1  
9 of 9  
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06  
©2006 Peerless Industries, Inc. All rights reserved.  
Peerless is a registered trademark of Peerless Industries, Inc.  
All other brand and product names are trademarks or registered trademarks of their respective owners.  
 

Paxar Printer Monarch 9476 User Manual
Peavey Musical Instrument Amplifier KB A 100 User Manual
Peavey Stereo Amplifier MA 212T User Manual
Philips Carrying Case US2 PH62008 User Manual
Philips Car Video System BDL3231 User Manual
Pioneer Car Stereo System DEH 8018ZT User Manual
Pioneer DVD Player DVD 116 User Manual
Pioneer DVR DVD CD WRITER User Manual
Portsmith Crib PS6PM5C 10 User Manual
POSIFLEX Business Machines Computer Monitor 202EI User Manual