C3611M (12/07)
EDI5000-AD2088 Data Interface
Quick Start Guide
CONNECT THE EDI5000-AD2088 TO AN AD MATRIX SYSTEM
MATRIX MONITOR
CAMERA 1
CAMERA 2
AD MATRIX
AD2088 MATRIX KEYBOARD
REVERSED
DATA CABLE
REVERSED
DATA CABLE
AD DUAL 8-PIN
TERMINAL BLOCK
9 VAC
1
2
3
8
7
6
8
1
GND
7
6
2
3
COM 1
Tx+
Rx+
4
5
4
5
COM 2
Rx+
Tx+
GND
EDI5000-AD2088
Figure 1. Connect the EDI5000 to the AD Matrix System
z
Table A. EDI5000 and AD2088 RS-232 Pin Assignments
Pin Assignment
RS-232 Data Rx+
Ground
AD2088 Keyboard
PIN 5
PIN 7
EDI5000 COM 1
PIN 1
PIN 5
RS-232 Data Tx+
Pin Assignment
RS-232 Data Rx+
Ground
PIN 4
AD Matrix
PIN 5
PIN 9
EDI5000 COM 2
PIN 2
PIN 7
PIN 6
RS-232 Data Tx+
PIN 4
PIN 10
NOTE: The alarm and relay inputs on the data interface are reserved for
future use, and are not included in this table.
C3611M (12/07)
1
OPERATE THE EDI5000-AD2088
When an operator is viewing live video from the matrix system, the keyboard commands and options are controlled by the matrix system, and
they function as described in the matrix system documentation.
When an operator is viewing either live video from an Endura system camera or recorded video, the keyboard commands and options are
controlled by the EDI5000 data interface, and they function as described in this section.
START ENDURA SCRIPT
STOP ENDURA SCRIPT
JUMP BACK
PAUSE
SITE
MONITOR
CAMERA
ENTER
AUXILIARY
CONTROL
PRE
SET
OFF
ON
PATRN
VCR
IRIS
PLAY
BLACK
CLOSE
OPEN
CRAPS
SLOTS
F1
F2
RUN
HOLD
1
4
2
5
8
3
6
JACK
FOCUS
FAST FORWARD/
STEP FORWARD
COUNT
ROOM
NEAR
FAR
SALVO
PROG
SITE
POKER
PIT
7
9
TASK
VCR
OPERATE
PROGRAM
MENU
ACK
CLEAR
MON
CAM
LAST
NEXT
0
NEXT EVENT
ON-SCREEN DISPLAY
REWIND/STEP BACK
PREVIOUS EVENT
MARK EVENT
Figure 5. Operating the EDI5000 with the AD2088 Keyboard
PLAY
UP
DIGITAL ZOOM OUT
DIGITAL ZOOM IN
REWIND
FORWARD
LEFT
RIGHT
TOGGLE BETWEEN
LIVE AND RECORDED
VIDEO
PAUSE
DOWN
Figure 6. Controlling Recorded Video with the Joystick
Figure 7. Using Digital Zoom to Control Recorded Video
C3611M (12/07)
3
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States
|
|
|
|
|
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
Pelco, the Pelco logo, Endura, and the Endura logo are registered trademarks of Pelco.
© Copyright 2007, Pelco. All rights reserved.
Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation.
Mozilla and Firefox are registered trademarks of the Mozilla Foundation.
|