Pelco Cash Register ICI1000S Series User Manual

™

Inter-Check ICI1000S Series

Cash Register Interface System

Installation/Operation Manual

C1000M-B (1/96)

PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981

FAX (800) 289-9150 or (1-559) 292-3827

TABLE OF CONTENTS (Continued)

Section

Page

4.8 LOCATION ID SETUP ............................................................................................................18

4.8.1 Location ID Program ..................................................................................................18

4.8.2 Location ID On and Screen Position Set ...................................................................19

4.8.3 Location ID Off ...........................................................................................................19

4.9 CUSTOMER HEADER ...........................................................................................................19

4.10 DIAGNOSTICS .......................................................................................................................19

4.10.1 ProgramTransfer .......................................................................................................20

4.10.2 (DL) Burn-In Test .......................................................................................................20

4.10.3 (DL) Input Channel Port Test .....................................................................................20

4.10.4 Memory Tests ............................................................................................................21

4.10.5 System Signals Test...................................................................................................21

4.10.6 Video Screen Test......................................................................................................21

4.10.7 Graphics Screen Test.................................................................................................21

4.10.8 (DL) Pelco PIM Default Load .....................................................................................22

4.11 ALARM INPUT........................................................................................................................23

4.11.1 Alarm Input On/Off.....................................................................................................23

4.11.2 Alarm Trigger Dwell ....................................................................................................24

4.11.3 Screen Link ................................................................................................................24

4.11.4 Auxiliary Print Link .....................................................................................................24

4.11.5 Alarm Text ..................................................................................................................24

4.12 ALARM PROGRAMMING ......................................................................................................24

4.13 THE NV MEMORY WRITE PROTECT SWITCH ....................................................................25

5.0 TROUBLESHOOTING .....................................................................................................................26

5.1 TROUBLESHOOTING FLOW CHART ...................................................................................27

6.0 SPECIFICATIONS ............................................................................................................................29

7.0 WARRANTY AND REPAIR INFORMATION.....................................................................................29

APPENDIX A. HEXADECIMAL, DECIMAL AND BINARY CONVERSION TABLES .................................30

APPENDIX B. ICI1000PIM SWITCH SETTINGS.......................................................................................33

Pelco Manual C1000M-B (1/96)

iii

LIST OF ILLUSTRATIONS

Figure

Page

Basic ICI1000S Configuration Wiring Diagram ............................................................................3

ICI1000PIM Wiring Configuration ................................................................................................4

Standard RS-232 Style Wiring Configuration...............................................................................4

Printer Output and Alarm Input Wiring .........................................................................................5

Video Adjustment Locations ........................................................................................................6

Keypad Layout .............................................................................................................................7

Program Transfer Wiring Diagram ..............................................................................................20

Printer Output and Alarm Input Wiring .......................................................................................23

ICI1000PIM Switch Settings ......................................................................................................36

LIST OF TABLES

Table

Page

Data Screen ID ..........................................................................................................................11

Label Descriptors .......................................................................................................................25

ICI1000S Series Pinouts............................................................................................................25

REVISION HISTORY

Manual #

C1000M

Date

Comments

—

Original version.

C1000M-A

11/95

Revised to incorporate Programming Menu Map, Section 4.0,

and Troubleshooting Flow Chart, Section 5.1.

C1000M-B

1/96

Revised to include Appendix B, ICI1000PIM Switch Settings.

Pelco Manual C1000M-B (1/96)

INSTALLATION/OPERATION MANUAL

ICI1000S SERIES INTER-CHECK^®

CASH REGISTER INTERFACE SYSTEM

1.0 WARNINGS

Priortoinstallationanduseofthisproduct,thefollowing

WARNINGS should be observed.

1. Installation and servicing should only be done by

qualifiedservicepersonnelandconformtoalllocal

codes.

4. OnlyusereplacementpartsrecommendedbyPelco.

5. After replacement/repair of this unit’s electrical

components, conduct a resistance measurement

betweenlineandexposedpartstoverifytheexposed

parts have not been connected to line circuitry.

2. Unless the unit is specifically marked as a NEMA

Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is

designed for indoor use only and it must not be

installed where exposed to rain and moisture.

3. The product and/or manual may bear the following

marks:

This symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present

within this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION:

TOREDUCETHERISKOFELECTRICAL

SHOCK, DO NOT REMOVE COVER. NO

USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

Please thoroughly familiarize yourself with the information in this manual

prior to installation and operation.

Pelco Manual C1000M-B (1/96)

2.0 SCOPE

In addition to the high performance and reliability

you’ve come to expect from Pelco products, the Inter-

Check ICI1000S Series offers the following MAIN

FEATURES:

The information contained within this manual covers

the installation and operation of the Inter-Check^®

ICI1000S Series cash register interface system.

•

Monitors one device, cash register or ATM ma-

chine.

Installation should be in accordance with all applicable

local and national electric codes, utilizing approved ma-

terials only.

Exception flagging for special alarm flags such as

VOID or REFUND.

Please familiarize yourself with the information in this

manual prior to installation and operation.

Exception flagging on numerical values such as

price and the manipulation of these values.

2.1 DESCRIPTION

•

30 separate exceptions can be programmed.

The Inter-Check terminal monitor, or P.O.S., interfaces

with mostATM machines and popular cash registers. It

is compatible with most standard CCTV cameras, video

tape recorders and monitors. The Inter-Check is the heart

of a large family of Pelco products which are designed

to reduce losses in any financial institution.

One programmable alarm output for VCR control.

One programmable alarm input for sensing of any

closure.

•

Completely programmable data channel.

Self-diagnostics to check for proper operation.

Easy on-screen, menu-driven programming.

Non-volatile memory for program storage (no bat-

tery needed).

•

Horizontal and vertical fine tune controls.

Character size, intensity and video gain controls.

Program transfer function between another Inter-

Check ICI1000S Series unit or Personal Computer

(PC).

•

Program transfer between an Inter-Check ICI1000S

Series and a PC requires special software designed

by Pelco Systems. If interested in this option, con-

tact a Pelco representative.

•

Compact 64 function keypad used to program the

Inter-Check ICI1000S Series.

The Inter-Check ICI1000S Series keypad can be

ordered for either external operation or hidden in-

ternal operation. Your choice must be specified

upon the initial order.

Pelco Manual C1000M-B (1/96)

3.0 INSTALLATION

NOTE: Do not mount the Inter-Check

ICI1000S Series unit until all connections are

made and programming is complete. Video ad-

justments on the bottom of the Inter-Check

ICI1000S Series may need to be accessible

during the initial set-up.

To begin installation, refer to the following instructions

and Figures 1 and 2.

3.1 INSTALLING INTERFACE CABLE

1. Install interface cable and PIM (if applicable) into

the cash register according to the instructions sup-

plied with your interface cable. Do not power up

PIM .

3.2 BASIC INSTALLATIONS

For basic installations, perform the following steps:

Install an 18 gauge, two-conductor shielded cable

between the interface cable/PIM and the ICI1000S

unit using the ICI1000WK (wiring kit) supplied

with your ICI1000S (refer to Figures 2 and 3). This

kit contains two RJ14 phone jacks and one straight-

through six conductor cable.

1. Connect the cable from your video camera to the

BNC labeled “VIDEO IN” on the Inter-Check

ICI1000S (refer to Figure 1). This normally comes

from your camera, splitter, switcher or quad. For

Coaxitron matrix installations, connect the cable

from the desired MONITOR OUTPUT to the BNC

labeled “VIDEO IN” on the Inter-Check unit.

WARNINGS: Do not power up the Inter-

Check ICI1000S Series unit until all other con-

nections have been made.

2. Connect a cable from the BNC labeled “VIDEO

OUT” on the Inter-Check ICI1000S Series to the

video input of your video cassette recorder or

monitor.

Only use the power supply supplied with the Inter-Check

ICI1000S Series unit. Other power supplies may damage

the unit.

Figure 1. Basic ICI1000S Configuration Wiring Diagram

Pelco Manual C1000M-B (1/96)

To Inter-Check Unit

Straight through

phone cable

Straight through

phone cable

User-supplied cable.

18 AWG shielded wire is

suggested

User-supplied cable.

18 AWG shielded wire is

suggested

From ICI1000PIM

From RS-232 style input

NOTE: For RS-232 style applications only.

Figure 3. Standard RS-232 Style

Figure 2. ICI1000PIM Wiring Configuration

Wiring Configuration

Pelco Manual C1000M-B (1/96)

3. Connect the data cable from the register interface

cable (or PIM) to “DATA IN” on the Inter-Check

ICI1000S, using the ICI1000WK and 18 gauge, 2-

conductor shielded cable (see Figure 1).

8. Plug the power supply for the ICI1000PIM into a

120 VAC outlet. The monitor should now display

the register model number.

9. If using the auxiliary print feature, and/or alarm

inputs, follow the wiring diagram in Figure 4 for

proper installation.

4. If using alarms, attach a 22-gauge, 2-conductor

shielded cable from the “ALARM OUT” of the

Inter-Check ICI1000S Series unit to your VCR,

switcher, or other alarmable device.

5. Plug the power supply for the Inter-Check

ICI1000S Series unit into a 120 VAC outlet.

NOTE:The monitor should now show the ini-

tialization message shown below.

6. Use the keypad on top of, or inside, the ICI1000S

chasis to set the standard PIM defaults. Press ENT,

6, 8 and then ESC to return to monitoring mode.

This step is required for all ICI1000S systems (re-

fer to Figure 4).

Pelco

INTER-CHECK/S VER X.X

ROM CHECK = YYYY

CALC. ROM CHECK = YYYY

SYSTEM BEING INITIALIZED!

MM VER. Z.Z

NOTE: ICI1000SI models have an internal

keypad; ICI1000SE models have an external

keypad.

(register model # displayed here)

NOTE: If you do not receive this message,

refer to the troubleshooting guide in Section 5.0.

If your installation does not require the use of

an ICI1000PIM, the register model number will

not appear.

7. Set the dip switches on the front of the ICI1000PIM

to match the setting for your register model num-

ber. Use the ICI1000PIM switch settings located

in the ICI1000PIM manual or Appendix B of this

manual. If your register does not require an

ICI1000PIM, disregard this step.

Alarm

Out

Data

13 12 11 10 9 8 7 6 5 4 3 2 1

25 24 23 22 21 20 19 18 17 16 15 14

Alarm

Contact

NOTE: A serial printer used with the Inter-Check ICI1000S

Series must be set at 1200 baud, 8 bits, no parity.

Figure 4. Printer Output and Alarm Input Wiring

Pelco Manual C1000M-B (1/96)

3.3 VIDEO ADJUSTMENTS

•

Gain adjusts the entire video screen.Too much gain

will distort the video picture. To reduce video gain,

turn the potentiometer labeled “G” slightly counter-

clockwise.

All video adjustments are located on the bottom of

the Inter-Check unit (refer to Figure 5). Using a non-

metallic screwdriver, make any necessary adjustments

as follows:

•

Horizontal Size adjusts the width of the text. To

increase the text width, turn the potentiometer la-

beled “S” slightly clockwise.

•

Horizontal Positioning adjusts the height of the

displayed text. To raise the text position, turn the

potentiometer labeled “H” slightly clockwise. This

adjustment will also correct double-sized charac-

ters appearing on the screen.

Character Size adjusts the size of the characters.

There are four selections. Set the switches marked

“C” in one of the following choices: both up, both

down, first switch up and second one down, or first

switch down and second one up.

•

Vertical Positioning adjusts the lateral position of

the displayed text. To move the text to the left, turn

the potentiometer labeled “V” slightly clockwise.

This adjustment will also correct “jittering” text.

Intensity adjusts the brightness of the text. To in-

crease the intensity of the text, turn the potentiom-

eter labeled “I” slightly clockwise.

UNLOCKED

LOCKED

V H I

NV MEMORY

SWITCH

Figure 5. Video Adjustment Locations

Pelco Manual C1000M-B (1/96)

4.0 INTER-CHECK ON-BOARD

KEYPAD OPERATION

1. Power down the Inter-Check ICI1000SI unit.

2. Remove the four cover screws with a Phillips

screwdriver and set the cover aside.

The Inter-Check ICI1000S Series features a compact,

64 function keypad used for all programming functions.

Refer to Figure 6. The keypad contains 16 keys. The

four keys on the right side of the keypad are used for

both cursor movement and “shift operations”. The re-

maining keys contain alpha, numeric, and other char-

acters for editing your program. These keys each con-

tain five functions when used with the shift keys.

3. Power up the ICI1000SI unit.

4. Program the Inter-Check unit for your particular

application.

5. When finished programming, replace the cover and

screw down firmly.

To select:

Press:

4.2 THE NV MEMORY WRITE PROTECT

SWITCH

White Character

Color Character

Desired Key

Cursor key of matching color

and then desired key.

Desired arrow key twice.

Enter (ENT)

Your new Inter-Check ICI1000S Series incorporates a

Non-Volatile (NV) type memory. This type of memory

does not require a battery to operate. Refer to Figure 5

for the location of this switch and note the locked and

unlocked positions. This switch must be positioned in

the UNLOCKED position if you intend on program-

ming the Inter-Check ICI1000S Series unit. If the switch

is in the LOCKED position and you try to enter pro-

gramming data, an “ERROR IN WRITING NV

MEMORY!!!” warning will be displayed on the moni-

tor screen. To allow programming, simply position the

write protect switch to the UNLOCKED position. When

programming is complete, position the switch to the

LOCKED position. This will protect your programming

from possible errors that may occur during AC power

fluctuations or complete Inter-Check ICI1000S Series

power loss.

Cursor Movement

Main Menu

Exit Main Menu

Escape (ESC)

4.1 PROGRAMMING THE ICI1000SI

NOTE: Please familiarize yourself with the

information in this manual prior to installation

and operation. Contact the customer's register

dealer/installer prior to installation and opera-

tion. Some warranties and/or service agree-

ments may be affected.

If your Inter-Check unit is an ICI1000SI, it utilizes an

internal keypad for programming all parameters. Fol-

low the steps below prior to programming.

Figure 6. Keypad Layout

Pelco Manual C1000M-B (1/96)

ICI1000S PROGRAMMING MENU TREE

Channel Program Menu

Communication Setup Menu

1. Communication Setup

2. Data Format/Communica-

tion Protocol

1. Communication Parameters

2. Device Addresses

3. Video Parameters

4. ATM Line Select

System Program Menu

Carriage Return Menu

1. Alarm Outputs

2. Carriage Return Control

3. Channel Screen Data

Position

1. Exception Auto CR

2. End Of Line Stop

4. Printer Settings

Monitoring

Mode

5. Exception Alarm Settings

6. Exception Alarm Text Edit

7. Exception Column Line

↵ ENT

Clock Program Menu

1. Set Clock

2. Clock ID On and Screen

Position Set

3. Clock ID Off

4. USA Standard Date

5. European Date

6. Auto Clock Set

Main Program Menu

1. Channel 1 Setup

2. System Parameters

3. Clock Setup

4. Location ID Setup

5. Customer Header

6. Diagnostics

Location ID Setup Menu

7. Alarm Inputs

1. Location ID Program

2. Location ID on and

Screen Position Set

3. Location ID Off

Diagnostics Selection Menu

1. ProgrammTransfer

2. (DL) Burn In Test

3. (DL) Input Channel Port

Test

4. Memory Tests

5. Signals Test

6. Screen Test

7. Graphics Test

8. (DL) PIM Default Load

↵ ENT Key moves Inter-Check

Alarm Input Menu

into the programming

mode from the monitoring

mode

1. Alarm Input On/Off

2. Alarm Trigger Dwell

3. Screen Link

4. Auxiliary Print Link

5. Alarm Text

ESC

Key returns to the

previous menu

Select catagories by

number

Pelco Manual C1000M-B (1/96)

4.3 CHANNEL SETUP

NOTE: If the current settings are accept-

able, press the ESC key which returns to the

CHANNEL PROGRAM SELECTION

MENU. If you wish to change the communi-

cation parameters, press “1”. To change the

device addresses press “2”.

There are two ways you can view your current channel

parameters:

1. Press the “1” key on your keypad while in the

monitoring mode.

2. Select CHANNEL SETUP (#1) in the MAIN PRO-

GRAM MENU.

4.3.2 Communication Parameters

This menu enables you to program the data string for-

mat, baud rate, and character set into the Inter-Check

ICI1000S series.

After executing one of these steps, an example of what

you might see is shown below:

SELECTED: CHANNEL

Pelco PIM STANDARD

NOTE: If you do not want to change items

within this menu, simply press ESC. The ESC

key will save the contents on the current line

and bring you to the prompt on the next line.

9600 BAUD,8 BITS,OFF PARITY

NRZ,ASCII,DATA INVERT

DEVICE ADDRESS 1 = 00H 0

DEVICE ADDRESS 2 = 00H 0

NOR. VID,OFF ID.,30 CHARACTERS

18 LINES,DATA DWELL=0

ALARM DWELL : 6/D1

BAUD RATE =?

This prompt enables you to change the baud rate. Enter

the appropriate data and press ENT to save. Use 9600

when connecting to a PIM. Setting the baud to 0 will

turn off the data channel.

EALRM = ON/VP PNTR = OFF

CHANNEL PROGRAM SELECTION MENU

1. COMMUNICATION SETUP

2. DATA FORMAT/COMMUNICATION PROTOCOL

3. VIDEO PARAMETERS

BITS (7 or 8) =?

Enter the appropriate number of data bits by pressing a

7 or 8 on your keypad. Use 8 when connecting to a

PIM.

4.3.1 Communication Setup

This selection allows you to set COMMUNICATION

PARAMETERS and DEVICEADDRESSES. The com-

munication parameters must be programmed correctly

in order for the Inter-Check ICI1000S Series to accept

data from your interface. Device addresses are used pre-

dominantly in ATM programming. Upon entering this

menu, you will notice that the channel’s current COM-

MUNICATION SETUP parameters are displayed as

shown below.

PARITY = 1. ODD, 2. OFF, 3. EVEN

Enter the correct parity configuration of your device

by selecting 1, 2 or 3. Choose #2 for a PIM.

1=NRZ OR 2=NRZI

Choose the appropriate code transmission format by

selecting 1 or 2. NRZ is the most common format. An

exception to this is the SNA/SDLC type of communi-

cations. Select #1 for normal PIM applications.

COMMUNICATION SETUP MENU

SELECTED: 9600 BAUD,8 BITS,OFF PARITY

NRZ,ASCII,DATA INVERTED

DEVICE ADDRESS 1 = 00H 0

DEVICE ADDRESS 2 = 00H 0

1. COMMUNICATION PARAMETERS

2. DEVICE ADDRESSES

Pelco Manual C1000M-B (1/96)

1=ASCII OR 2=EBCDIC

Enter the appropriate address as explained above. Af-

ter pressing ESC or entering an address you will be in

the CHANNEL PROGRAM MENU once again. The

current programmed addresses are displayed in both

Hexadecimal and Base 10 formats.

The fifth prompt sets up the character set for the Inter-

Check ICI1000S Series. Press a “1” to select ASCII

and “2” for EBCDIC. The ASCII character set is the

most common whereas EBCDIC is used predominantly

in IBM systems. Select ASCII when connecting to a

Pelco PIM.

NOTE: If you are using SNA or SDLC for-

mats, make both device addresses the same

value.

1=DATA NON INVERT OR 2=DATA INVERT

NOTE: Setting both addresses to 00 puts the

Inter-Check ICI1000S Series unit into diagnos-

tics mode. In this mode the Inter-Check

ICI1000S Series unit will display all network

activity including the proper device address in

your installation.

This prompt sets up the Inter-Check ICI1000S series to

receive either inverted or non-inverted data. This se-

lection varies from one register to the next. Choose

DATA INVERT in PIM applications.

After you have answered all of the prompts, the Inter-

Check ICI1000S Series will show you the changes (if

any) you have made. If the changes are correct, press

ESC. If the changes are incorrect, follow the same steps

just described. Again note that if you do not want to

edit a certain parameter you can skip and save the ini-

tial settings by pressing ESC.

4.4 DATA FORMAT/COMMUNICATION

PROTOCOL

Select this menu by pressing #2 in the CHANNEL

PROGRAM MENU. The menu allows you to choose

the type of device you are connecting to.After pressing

#2 the current settings will be displayed. An example

might be:

4.3.3 Device Addresses

Select this menu by pressing #2 in the Communica-

tion Setup Menu. As mentioned earlier, DEVICEAD-

DRESSES are used in ATM installations. A device

address is the electronic address of the specific ATM

being monitored. The Inter-Check ICI1000S Series

allows you to enter two DEVICE ADDRESSES.

DATA PROTOCOL MENU

SELECTED: PIM STANDARD

To select the proper communication protocol for your

application, use the ENT key or the up and down cur-

sor control keys to scroll through your options. When

you reach the device, save the selection by pressing

ESC.

NOTE:Appendix A illustrates a Hexadeci-

mal to Decimal conversion chart that you may

find helpful. Also, set the unused device ad-

dress to 00H.

Current options include:

•

PIM STANDARD

PIM GRAPHICS

ICL PRINTER

After pressing #2 the screen will display:

DEVICE ADDRESS -1 3 DECIMAL DIGITS (000-

255) = ?

WAYNE-DRESSER PRINTER

DIEBOLD 910/911 : NCR 751/279

DIEBOLD 910/911 : TC 500/700

DIEBOLD 910/911 : TC 500/700 SYNC

DIEBOLD 910/911 : IBM 3275

DIEBOLD 910/911 : IBM 2260

DIEBOLD 910/911 : IBM 2265

DIEBOLD 910/911 : SNA/SDLC

IBM3624

This prompts you to enter the appropriate address up to

three digits in length. This address must also be be-

tween the specified boundaries, 000-255. If less than

three digits are used, you must press ENT to save. Press-

ing the ESC key will return you to the CHANNEL PRO-

GRAM MENU.

NCR NATIVE MODE

IBM NATIVE MODE

RS232 STANDARD PRINTER

The next prompt reads:

DEVICE ADDRESS -2 3 DECIMAL DIGITS (000-

255) = ?

Pelco Manual C1000M-B (1/96)

4.5 VIDEO PARAMETERS

NUMBER OF LINES DISPLAYED (01-18)

To view the video parameters setting press #3 in the

CHANNEL PROGRAM MENU. The Inter-Check

ICI1000S Series will display the current settings. Press-

ing ESC will skip the current line and allow you to con-

tinue in the CHANNEL PROGRAM MENU.

This selection specifies the number of lines you wish

to be displayed. Select the appropriate number of lines

for your application and press enter. The default value

is 18 lines.

DATA DWELL TIME IN SECONDS (000-255)

VIDEO PARAMETER SETUP MENU

SELECTED: NOR VID, OFF ID., 30 CHARACTERS

18 LINES, 0 DATA DWELL

The data dwell time defines the duration of time the

data will stay on the screen. Simply enter the appropri-

ate number of seconds that best suits your needs and

press ENTER. For example, if you want the data to stay

on the screen for 5 seconds after the last line is printed,

press 5 for the data dwell time. The default value is 0

which forces the data “on” at all times.

ENTER DATA OR ESC TO SKIP

REVERSE VIDEO = 1. REV, 2. OFF =?

You may find this feature very useful in bright lighting

conditions. When it is turned on it creates a dark back-

ground around the white text displayed on the monitor.

Reverse video is used for ease in readability. If you

want this feature turned on, press 1. For normal video

presentation press 2.

Example:

A five-second dwell is entered as 005 ENTER

4.6 SYSTEM PARAMETERS

(Selection #2 from the main menu)

4.6.1 Alarm Output

ID. VALUE 0 = OFF, (1-7) = “A” TO “G”

This second prompt enables you to identify the data

screen. This ID will remain on the screen at all times.

For example, you may want to label the data channel

“A” for ease in recognition while viewing the video

tape. This feature is very useful if two Inter-Check

ICI1000S Series are used together on a single VCR and/

or monitor. Refer to Table 1 for a cross-reference. If

you do not wish a screen ID value, press 0 or ESC.

This selection allows you to set the alarming output

features. This output is a normally open closure used to

control external alarmable devices. This output can be-

come active if:

•

Data is present on the channel.

Exception is met on the data channel.

Closure is seen on the alarming input.

Table 1. Data Screen ID

Selection

Display

The first line in this menu is:

ALARM DWELL : 6/D1

(D1 = Data Alarm ON; E1 = Exception Alarm ON)

(I1 = Alarm Input On)

This line gives you the current status of the alarming

output. If, for example, the first line of this menu read

“ALARM DWELL : 30/D1E1” the alarm would remain

active for 30 seconds upon the occurrence of either data

or an exception on the data channel. 6/D1 is the default

factory setting.

MAX CHARACTERS PER LINE (01-80)

Selection #3 designates how many characters per line

you want displayed on the monitor. Simply press any

number from 1-80 that best suits your application. De-

fault value is 30.

Pelco Manual C1000M-B (1/96)

The next prompt is:

Selecting 1 in this menu turns off the auto carriage re-

turn feature and brings you back to the EXCEPTION

AUTO CR MENU. Selecting 2 in this menu will bring

up the next prompt:

ALARM DWELL TIME IN SECONDS

(001-255)=?

Simply enter in the amount of time you wish the alarm-

ing output to remain active in seconds and press ENT.

CR DWELL TIME IN SECONDS (000-255)=?

At this prompt enter the amount of time in seconds you

wish to wait before the Inter-Check unit automatically

inserts a return. You will then return to the EXCEP-

TION AUTO CR MENU.

The following prompts allow you to activate the alarm-

ing output upon the occurrence of data and/or an ex-

ception on the channel.

CHANNEL DATAALARM ?

1=OFF 2=ON

Entering 2 in the CARRIAGE RETURN MENU will

bring up:

CHANNEL EXCEPTION ALARM ?

1=OFF 2=ON

END OF LINE STOP MENU

STOP

4.6.2 Carriage Return Control

SELECTED: OFF

The carriage return control feature allows you to use

your Inter-Check ICI1000S Series unit with devices that

do not execute a carriage return at the end of the data

lines or a device that has a scrolling message when trans-

actions are not taking place. If a carriage return is not

found at the end of a line, the Inter-Check ICI1000S

Series unit cannot correctly place the text on the screen

or do exceptions on that line. This problem can be solved

with the EXCEPTIONAUTO CR feature of this menu.

The END OF LINE STOP feature allows you to force

the Inter-Check ICI1000S Series to stop its display at

the end of the line when a carriage return is not re-

ceived. This is useful when a device scrolls messages

when transactions are not taking place.

ENTER DATA OR ESC TO SKIP

1=OFF 2=ON

Enter your choice by pressing 1 or 2. You will be brought

back to the CARRIAGE RETURN MENU.

4.6.3 Camera Screen Data Position

This option allows you to position the data anywhere

on the monitor’s screen. When this option is selected a

block of ones (1) is displayed on the monitor which

represents the current size and position of the displayed

data. Move the block by pressing the arrow keys twice

for each increment. After the block has been moved to

the desired position, press ENT to save.

NOTE:The “end of the line” is dependent on

the MAXIMUM CHARACTERS PER LINE

setting in the VIDEO PARAMETERS menu.

4.6.4 Printer Settings

The PRINTER SETTINGS selection allows you to en-

able the auxiliary printer output port and select the data

being sent to the printer. The first thing displayed in

this menu is the current status of the AUX port.

The first prompt in this menu is:

1. EXCEPTION AUTO CR

2. END OF LINE STOP

CHANNEL DATA TO AUX PRINT ?

1=AUX 2=OFF

Entering 1 for EXCEPTION AUTO CR will bring up

the following:

Pressing 1 will send the data received on the channel to

the auxiliary port.

EXCEPTION AUTO CR MENU

EXC. CR

SELECTED: OFF

Pressing 2 will turn off the auxiliary printer port.

CR DWELL:1

ENTER DATA OR ESC TO SKIP

1=OFF 2=ON

NOTE: A serial printer used with the Inter-

Check ICI1000S Series must be set at 1200

baud, 8 bits, no parity.

Pelco Manual C1000M-B (1/96)

4.6.5 Exception Alarm Settings

Programming Exceptions

(Selection #5 in the System Program Menu)

NOTE:In order for the Inter-Check ICI1000S

Series to “capture” exception text you must turn

on the EXCEPTIONALARM SETTINGS.An

example is shown below:

EXCEPTIONS are situations of special inter-

est that you can program into your Inter-Check

ICI1000S Series unit. They are used to alarm

your VCR or other alarmable devices when a

certain condition has been met. Exceptions can

also be directly printed to an external printer.

Exception flagging will save you valuable time

reviewing VCR tapes because you have the

ability to view only events of specific interest.

CHANNEL : EALRM = ON / PNTR = ON

ESC TO EXIT OR ENTER TO EDIT?

The above example shows that Channel Exceptions are

turned ON and are being “sent” to an auxiliary printer.

Press ENT to edit; the prompt reads:

Entering the Exception Menu

CHANNEL EXCEPTION FLAG ?

1=OFF 2=ON

To select the Edit Exception Text menu while

in the monitoring mode, follow these steps:

Press 1 to turn channel exceptions OFF or 2 for ON.

Press the ENT key (you will hear one tone).

The MAIN PROGRAM MENU will be dis-

played.

CHANNEL EXCEPTION MARKER VIDEO

PRINT ?

1=OFF 2=ON

MAIN PROGRAM MENU

The Exception Marker Video Print displays asterisks

around an exception appearing on the monitor and/or

printer. It is designed to capture your attention when an

exception has occurred. Press 1 or 2 for your choice.

1. CHANNEL SETUP

2. SYSTEM PARAMETERS

3. CLOCK SETUP

4. LOCATION ID. SETUP

5. CUSTOMER HEADER

6. DIAGNOSTICS

CHANNEL EXCEPTION MARKER AUX.

PRINT ?

1=AUX 2=OFF

7. ALARM INPUTS

This menu is used if you have an external serial printer.

This menu enables you to send data to the auxiliary

output port. If you do not utilize an external printer,

press #2.

Press #2 (you will hear one tone) which cor-

responds to the SYSTEM PARAMETERS

MENU. The following text should appear:

SYSTEM PROGRAM MENU

1. ALARM OUTPUTS

2. CARRIAGE RETURN CONTROL

3. CHANNEL SCREEN DATA

POSITION

4. PRINTER SETTINGS

5. EXCEPTION ALARM SETTINGS

6. EXCEPTION ALARM TEXT EDIT

7. EXCEPTION COLUMN LINE

Pelco Manual C1000M-B (1/96)

4.6.6 Exception Alarm Text Edit

ENT

Saves changes to one line in the Text

Editor.

(Selection #6 in the System Program Menu)

DEL

ESC

Deletes a line.

After Pressing #6 the following numbers will appear

across your monitor screen:

Saves any changes made in the edi-

tor and exits back to the SYSTEM

PROGRAM MENU.

12345678901234567890123456789012345678901234567890

= =

(^)

Wildcard or column specific charac-

ter. The caret (^) symbol is displayed

by pressing the right arrow key fol-

lowed by a 6.

This row of numbers is referred to as the Exception

Column Line. This will aid you in programming vari-

ous parameters which will be covered later in this sec-

tion. As mentioned earlier, the Exception Column Line

exactly matches the EXCEPTION COLUMN LINE in

the monitoring mode (when it is turned on).

SPACE

(\)

Inserts position spaces. To insert a

space, press the right arrow key.

The text editor has two prompts; == and =>.

The back-slash (\) is used to describe

a transaction. This symbol is created

by pressing the right arrow key, fol-

lowed by an 8.

The == prompt signifies that the edit mode has not been

entered on that line.You may either edit the line or press

the ENT key to skip.

( )

The “double bar” ( ) is used in price

point formats to define and manipu-

late a string of numbers. This sym-

bol is created by pressing the right

arrow key, followed by a 9.

The => prompt signifies that the edit mode has been

entered on that line. You must view the whole line of

text before you press enter or the line will be deleted.

NOTES: The ENT and the INS key must be

used together to save all changes. If you make

changes within a line, move the cursor to the

end of the line with the RIGHT ARROW key

and press ENT. Pressing the ESC key deletes

all the changes and the text returns to its origi-

nal settings.

NOTE: The next three symbols are used in

conjunction with the “double bar” described

above.

(=)

(<)

Used to identify an equal compari-

son in the price point format.

Unlike the ICI2000D, the ICI1000S automati-

cally converts all text into capital letters for com-

parison purposes. Therefore, when program-

ming exceptions, you do not have to worry

about capital and lower-case designations.

Enables you to flag on values less

than a specified number being de-

fined with the double bar in the price

point format.

(>)

Enables you to flag on values greater

than a specified number being de-

fined with the double bar in the price

point format.

4.6.6.1 Keypad Definitions

Listed below are the various keys you will be using

when programming exceptions on the Inter-Check

ICI1000S Series. Pelco suggests that you become fa-

miliar with the functions before attempting to use the

exception menus.

INS

Saves all changes in Text Editor and

exits back to SYSTEM PROGRAM

MENU. The INS key is also used in

conjunction with the ENT key.

Pelco Manual C1000M-B (1/96)

4.6.7 Programming Stratagies

Exceptions Using the COLUMN SPECIFIC

Strategy

Exceptions Using the GLOBAL Strategy

This is used to flag on specific placement of text on

the register ticket. This type of exception uses the (^)

character on your keypad. It is used to capture text ac-

cording to the position on the register ticket. When this

type of exception strategy is used, the Inter-Check

ICI1000S Series searches for specific column place-

ment of data defined by the number of ^ symbols you

use. It may be useful for you to refer to the explana-

tion of the EXCEPTION COLUMN LINE to ensure

proper positioning.

This is used to flag on any text regardless of placement

on the register ticket.

EXAMPLE: Flagging on any VOID within

your system.

You must first enter into the ExceptionAlarm Text Edit

mode. To do this press #2 in the MAIN PROGRAM

MENU (SYSTEM PARAMETERS). Then press #6 in

the SYSTEM PROGRAM MENU (EXCEPTION

ALARM TEXT EDIT).

EXAMPLE: Flagging on department num-

ber 5200 but your register prints it as “ 5200

40.00 “

The display should now read:

123456789012345678901234567890123456789012345678901234567890

= =

1. Turn on the exception column line by pressing se-

lection #7 (EXCEPTION COLUMN LINE) in the

SYSTEMS PARAMETER MENU.

1. Type VOID to match the exact format it is printed

on the register ticket.

2. Press ESC three times to return to the monitoring

mode.

123456789012345678901234567890123456789012345678901234567890

=>VOID

Let’s say the display read:

2. Press ENT to save the exception.

3. Press INS to save the changes.

123456789012345678901234567890123456789012345678901234567890

5200

$40.00

3. Press ENT to access the MAIN MENU.

4. Turn on the EXCEPTION ALARM SETTINGS.

For further instructions, refer to EXCEPTION

ALARM SETTINGS previously described.

4. Press 2 to access the SYSTEMS PARAMETER

MENU.

5. Press ESC three times to resume monitoring.

5. Press 6 to edit exception text.

6. Key in the following:

123456789012345678901234567890123456789012345678901234567890

=>^^^^^5200

7. Press ENT to save the exception.

8. Press INS to save the changes.

9. Press ESC three times to return to the monitoring

mode.

Pelco Manual C1000M-B (1/96)

Exception Flagging Using WILDCARDS

The PRICE POINT Exception Flag

Strategy

Used to flag on groups of transactions or departments.

This type of exception also uses the caret (^) character

and is usually used with the COLUMN SPECIFIC type

of exception. Again, it is suggested that you use the

EXCEPTION COLUMN LINE.

The Double Bar character ( ) key enables you to flag

or compare any number that is equal to, greater than,

or less than a desired number.

EXAMPLE: Flagging on any price over

$40.00 in department 52XX and labeling the

exception with a descriptor of JEWELRY DE-

PARTMENT.

EXAMPLE: Flag any transaction in your jew-

elry department where the department number

is 5200-5299. Also, the register prints it out as

“

5250 $40.00 “

1. Select 7 in the SYSTEM PARAMETER MENU.

This turns on the Exception Column Line in the

monitoring mode.

1. Follow steps 1-5 in the previous example.

2. Key in the following:

2. Press ESC three times to return to the monitoring

mode.

123456789012345678901234567890123456789012345678901234567890

=>^^^^^52^^

Let’s say the screen read:

3. Follow steps 7-9 in the previous example.

12345678901234567890123456789012345678901234567890

NOTE: When the ^ key is used as the first

character of exception text, it causes that line

to be Column Specific.Also, when the ^ is pre-

ceded by any other character it will then be read

as a Wildcard character.

5248

$40.00

3. Press ENT.

4. Press 2 to access the SYSTEMS PARAMETER

MENU.

Exception Marking Using the

DESCRIPTOR

5. Press 6 to edit exception text.

6. Key in the following:

The back-slash symbol (\) is used to describe a certain

transaction you are flagging. It is printed on the line

after the exception in the video or printer flag display.

12345678901234567890123456789012345678901234567890

=>^^^^^52^^ 40.00 >\JEWELRY DEPARTMENT

EXAMPLE: Describe the department 5200-

5299 in the above example with a descriptor of

JEWELRY DEPARTMENT.

7. Press ENT to save the exception.

8. Press INS to save the changes and exit.

1. Follow the same programming steps used in the

previous example.

9. Turn on the Exceptions. Do this by pressing #5 in

the SYSTEM PROGRAM MENU and answering

the prompts. For a further explanation on how to

turn on exceptions refer to EXCEPTIONALARM

SETTINGS.

2. Key in the following:

123456789012345678901234567890123456789012345678901234567890

^^^^^52^^\JEWELRY DEPARTMENT

10. Press ESC three times to return to the monitoring

mode.

Pelco Manual C1000M-B (1/96)

Notice that the second double bar is placed directly af-

ter the data you are interested in. This format holds true

for any transaction you wish to flag using the double

bar format. The first double bar has a leeway of 15 char-

acters or spaces. In other words, in the previous ex-

ample the first double bar could be placed at 15 spaces

to the left of the 4 in $40.00, but the second double bar

must be inserted directly after the last 0 in $40.00. There-

fore, if your register prints negative numerical values

with a minus sign behind the text and you wish to flag

this type of transaction, you must insert the minus sign

in front (some registers record a refund with a minus

sign). For example, if the above example printed out a

refund of $40.00 as 40.00- you would capture this data

as an exception by programming the Inter-Check

ICI1000S Series in the following format:

4.7 CLOCK SETUP

The Inter-Check unit can be programmed to display

the time and date on the video monitor in any conve-

nient location. The Inter-Check also accepts the USA

or European date structure. The AUTO CLOCK fea-

ture allows the Inter-Check unit to synchronize with

the cash register or ATM machine clock. If the register

or ATM has a clock that is displayed with the data, it is

suggested that the auto clock load feature be used. This

will remove the inaccuracy of using the Inter-Check’s

clock.

NOTE:The internal clock on the Inter-Check

ICI1000S Series is software generated and is

inaccurate.

-40.00 >\JEWELRY DEPARTMENT

4.6.8 Exception Column Line

(Selection #7 in the System Program Menu)

Entering 4 in the main menu will bring up the CLOCK

PROGRAM menu:

CLOCK PROGRAM MENU

1. SET CLOCK

This selection proves to be a valuable tool when edit-

ing exceptions. When this function is turned on, a row

of numbers will appear across the screen in the moni-

toring mode. The row of numbers will exactly match

the row found in the EXCEPTION ALARM TEXT

EDIT menu (explained prior). This function will save

you time when you have a lot of text or multiple spaces

between numbers or characters and are using column

specific exceptions. Examples of this function are also

explained in the following pages.

2. CLOCK ID. ON AND SCREEN POSITION SET

3. CLOCK ID. OFF

4. USA STANDARD DATE

5. EUROPEAN DATE

6. AUTO CLOCK SET

4.7.1 Set Clock

Entering 1 in this menu allows you to set the internal

clock. The following prompt will follow:

YR,MT,DY,HR,MN,SC,DW

XX XX XX XX XX

The cursor will start at the far left hand side and move

to the right as you enter the information. The backspace

key on the keyboard allows you to delete the previous

entry. The arrow keys allow you to move back and forth

without effecting the entered data. The DW position

indicates the day of the week, Sunday being the first

day. The clock uses the 24-hour system (military time)

so the hour is entered as a number from 01 to 24. The

day of the week is entered as a number from 01 to 07.

EXAMPLE: If the day is May 21, 1993 and

the time is 1:40:30 p.m. on a Monday, the fol-

lowing information would be entered:

YR,MT,DY,HR,MN,SC,DW

93 05 21 13 40 30 02

Pelco Manual C1000M-B (1/96)

4.7.2 Clock ID On and Screen

Position Set

DATE DELIMITER 1.(/) 2.(-)

Select 1 if the date displayed by the register uses (/) as

a delimiter.

Selection 2 in the CLOCK PROGRAM MENU will

turn the clock on and allow positioning on the screen.

Press the arrow keys twice for each increment to move

the time and date to the preferred position and press

ENT to save.

Select 2 if the date displayed by the register uses (-) as

a delimiter.

TIME DELIMITER 1.(:) 2.(-)

4.7.3 Clock ID Off

Use the same procedure for selecting the time delim-

iter as the date delimiter.

The 3rd selection in the menu will turn off the time and

date video display.

NOTE: The Autoclock Load does not dis-

criminate the seconds position. It will always

load in 30 seconds.

4.7.4 USA Standard Date

Pressing 4 will set the date in the USA standard format

(month, day, year).

4.8 LOCATION ID SETUP

4.7.5 European Date

(Selection #4 from the main menu)

Pressing 5 will set the date in the European standard

format (day, month, year).

The LOCATION ID is normally used to place the name

or location of the user’s store. The ID can be placed

anywhere on the screen and stays resident on the screen

at all times. This feature is useful when one party is

reviewing video tapes from multiple store locations.

4.7.6 Auto Clock Set

Choosing selection 6 in the CLOCK PROGRAM

MENU permits the use of the AUTO CLOCK feature.

In order to use this function, the register’s clock must

be displayed on the monitor by the ICI1000S. Most

registers will display this information. The program-

ming prompt begins:

Pressing 3 in the MAIN PROGRAM MENU will bring

you to the LOCATION ID SETUP menu:

LOCATION ID SETUP MENU

CHANNEL AUTOSET ?

1=OFF 2= ON

1. LOCATION ID PROGRAM

2. LOCATION ID ONAND SCREEN POSITION SET

3. LOCATION ID OFF

Pressing 1 will disable the AUTO CLOCK SET.

Pressing 2 will enable the AUTO CLOCK SET.

4.8.1 Location ID Program

Number 1 in this menu allows you to program the text

for the ID:

12 HOUR MODE LOOK ?

1=OFF 2=ON

ENTER DATAWANTED UPTO 12 CHARACTERS.

Select 1 if the register displays the time in a 24-hour

format.

(ESC) TO SKIP, (ENTER) TO ENTER,

(BS) TO BACKSPACE

Select 2 if the register displays the time in a 12-hour

format.

Enter the text you wish to have displayed, up to 12 char-

acters long, and press ENT to save.

NOTE: If the 12-hour mode is used the Inter-

Check looks for an “A” or a “P” designating

A.M. or P.M. In the 24-hour mode the Inter-

Check loads the time by numerical values.

Pelco Manual C1000M-B (1/96)

4.8.2 Location ID On and Screen

Position Set

4.10.1 Program Transfer

The PROGRAM TRANSFER function is used for easy

duplication of the Inter-Check ICI1000S Series program.

This is especially useful for transferring exception pro-

gramming to multiple Inter-Check ICI1000S Series units

within the same chain of stores. Programming can also

be transferred to an IBM compatible PC. This requires a

software program which must be ordered directly from

Pelco. To accomplish a program transfer a simple cable

can either be made or may be ordered from Pelco. Refer

to Figure 7 for proper wiring.

Pressing 2 in the LOCATION ID SETUP MENU will

turn the ID on at all times. It also allows you to posi-

tion the ID with the cursor control keys to the desired

screen display position.

4.8.3 Location ID Off

Pressing 3 will turn off the ID display.

4.9 CUSTOMER HEADER

(Selection #5 from the main menu)

Upon entering 1 in the DIAGNOSTICS MENU the

following prompt appears:

The CUSTOMER HEADER is the message displayed

when the Inter-Check ICI1000S Series is being reset

and initialized. This text may be changed to reflect the

name of the customer’s store or company. Pressing 6 in

the MAIN PROGRAM MENU will allow changing the

customer header:

1. SOURCE 2. DESTINATION

After connecting the cable between the two Inter-Check

units, enter #1 for SOURCE on the Inter-Check ICI1000S

Series that is sending the program. Then enter #2 on the

DESTINATION Inter-Check unit, or the one that is re-

ceiving the program data. The program will then be sent

automatically. Upon detection of an error in transmission,

the system will retry until the proper data is received or

until manually aborted by pressing ESC.

ENTER DATA WANTED UP TO 25 CHARACTERS

(ESC) TO SKIP, (ENTER) TO ENTER,

(BS) TO BACKSPACE

CAUTION: Both units must have the same

memory map version. The memory map is dis-

played upon completion of initialization.

Enter the header desired up to 25 characters in length

and press ENTER to save.

NOTE: Performing a DEFAULTLOAD (DL)

in the Diagnostics Menu will return the cus-

tomer header to the default setting.

MM VER. X.X

4.10.2 (DL) Burn-In Test

4.10 DIAGNOSTICS

(Test performed by Pelco personnel only)

4.10.3 (DL) Input Channel Port Test

(Test performed by Pelco personnel only)

(Selection #6 from the main menu)

WARNING:Some of the tests selected in the

DIAGNOSTICS MENU will cause the pro-

gramming in the Inter-Check ICI1000S Series

unit to be lost. These selections are preceded

by (DL) in the DIAGNOSTIC SELECTION

MENU.

NOTE: Some of the tests in the DIAGNOS-

TICS MENU can only be performed by fac-

tory trained personnel.

Pelco Manual C1000M-B (1/96)

Alarm

Out

Alarm

Out

Data

NOTE: For complete pin-out

information, refer to Table 3.

Figure 7. Program Transfer Wiring Diagram

4.10.4 Memory Tests

NOTE: If the Inter-Check ICI1000S Series

displays the message “ERRORWRITING NV

MEMORY!!!!!!”, the write protect switch on

the bottom of the Inter-Check ICI1000S Series

unit is in the wrong position for this test. Refer

to Section 4.2 and Figure 5 for an explanation

of this error message.

By entering 4 in this menu the following sub-menu is

displayed:

MEMORY TEST MENU

1. RAM TEST

2. VIDEO RAM TEST

3. (DL) NV MEMORY TEST

4. ROM CRC TEST

Pressing #4 will allow the Inter-Check ICI1000S Se-

ries unit to perform a CRC test on the Read Only

Memory. While this test is running, verify that the ROM

CHECK and the CALC. ROM CHECK numbers match.

If there is an error the system will beep and display the

two different ROM numbers. If a failure occurs, un-

plug and retry.

By selecting 1, the unit will perform a self test on its

Random Access Memory. This test is used to verify

system RAM integrity. The system will display an OK

message if the test passes or an address and data if it

fails. ESC brings the Inter-Check ICI1000S Series back

to the DIAGNOSTICS MENU.

4.10.5 System Signals Test

(Test performed by Pelco personnel only)

4.10.6 Video Screen Test

Selecting 2 in this menu will put the Inter-Check

ICI1000S Series into the VIDEO RAM TEST mode.

The video RAM is verified by a slotted, scrolling dis-

play in the upper left hand corner of the monitor. If an

error is detected an address and data will appear on the

screen. ESC brings the unit back to the DIAGNOS-

TICS MENU.

This test produces normal and reverse video images

covering the entire screen. It is used to verify video

character generation and system control.

4.10.7 Graphics Screen Test

WARNING: When the NON-VOLATILE

MEMORY TEST is selected all programming

is lost.

The number 7 selection in the diagnostics menu is used

to test the video graphics mode available on the Inter-

Check ICI1000S Series unit.

The NV MEMORY TEST, (3rd selection), is used to

verify the NON-VOLATILE MEMORY integrity. The

system will display OK if the test passes. Upon error,

the Inter-Check ICI1000S Series will display an address

and the data that was written into the memory location.

Pelco Manual C1000M-B (1/96)

4.10.8 (DL) Pelco PIM Default Load

2. Press #6 (you will hear two tones). The following

text will appear:

The Pelco DEFAULT LOAD should be executed for

the following situations:

DIAGNOSTICS SELECTION MENU

•

Before doing any programming of the Inter-Check

ICI1000S Series upon initial installation.

1. PROGRAM TRANSFER

2. (DL) BURN IN TEST

3. (DL) INPUT CHANNEL PORT TEST

4. MEMORY TESTS

After a firmware update has been completed.

5. SYSTEM SIGNAL TEST

6. VIDEO SCREEN TEST

7. GRAPHICS SCREEN TEST

8. (DL) Pelco PIM DEFAULT LOAD

Performing a default load sets up all parameters of the

Inter-Check ICI1000S Series unit to the default settings.

This feature of the Inter-Check ICI1000S Series should

be used in normal PIM installations. After executing a

(DL) the Inter-Check ICI1000S Series communication

parameters are set up to receive data from a PIM. The

Inter-Check ICI1000S Series communication param-

eters are set to the following values:

ESC TO QUIT OR SELECT # TO

PROGRAM

3. Press #8 (you will hear two tones). The Inter-Check

ICI1000S Series will prompt you:

9600 BAUD

8 BITS

DEFAULTS BEING LOADED

OFF PARITY

NRZ

The DIAGNOSTICS SELECTION MENU will be dis-

played again.

ASCII

DATA INVERTED

4. Press the ESC key (you will hear one tone). The

Inter-Check ICI1000S Series unit will return to the

monitoring mode and initialize again.

To execute a (DL), follow these steps:

1. Press ENT while in the monitoring mode (you will

hear one tone). The MAIN PROGRAM MENU

will be displayed.

NOTE: Each time you enter the SYSTEM

MENUS and ESC back into the monitoring

mode, the initialization message will be dis-

played.

MAIN PROGRAM MENU

5. After executing a (DL) Pelco PIM DEFAULT

LOAD, the Inter-Check ICI1000S Series system

parameters are set to the following:

1. CHANNEL SETUP

2. SYSTEM PARAMETERS

3. CLOCK SETUP

4. LOCATION ID. SETUP

5. CUSTOMER HEADER

6. DIAGNOSTICS

•

Data channel: set for Pelco PIM STANDARD

Data dwell time: continuous display

Lines displayed: 18 lines

Characters displayed: 30 characters

Alarm output : set for six seconds dwell when data

is received.

Data channel text positioning: column 1

Exception alarm: OFF

Auxiliary ports: OFF

7. ALARM INPUTS

ESC TO QUIT OR SELECT # TO

PROGRAM

•

Exceptions: not programmed

Location ID: not programmed

Pelco Manual C1000M-B (1/96)

4.11 ALARM INPUT

NOTE: For a complete table of status label

descriptions used in the Inter-Check ICI1000S

Series menu system refer to Table 2.

(Selection #7 from the main menu)

TheALARM INPUT can be connected to any normally

open (open loop) alarm device that can trigger a clo-

sure for at least one-half second. Once an alarm is valid,

the trigger is reset to open and will not detect the next

alarm until timeout. For correct wiring, refer to Figure

8 and Table 3.

4.11.1 Alarm Input On/Off

This selection enables you to turn the ALARM INPUT

on or off. You can also route an ALARM INPUT ex-

ception to the output port (i.e., VCR). After pressing

#1 you will see the following:

After selecting #7, the following text will be displayed:

ALARM IN

ALARM DWELL : 6/D1

1=OFF 2=ON

ALARM IN DWELL : 0/OFF/V1 = =>ALARM

Press one (1) to turn the input off, or two (2) to turn the

input on. The next prompt will read:

ALARM INPUT PROGRAM MENU

1. ALARM INPUT ON/OFF

2. ALARM TRIGGER DWELL

3. SCREEN LINK

TRIGGER ALARM OUT

1=OFF 2=ON

4. AUXILIARY PRINT LINK

5. SCREEN HOMING

6. ALARM TEXT

Select one (1) to not trigger the ALARM OUTPUT on

when an alarm from the input is received. Select two

(2) to trigger the ALARM OUTPUT when an alarm

from the input is received.

Alarm

Out

Data

13 12 11 10 9 8 7 6 5 4 3 2 1

25 24 23 22 21 20 19 18 17 16 15 14

Alarm

Contact

NOTE: A serial printer used with the Inter-Check ICI1000S

Series must be set at 1200 baud, 8 bits, no parity.

Figure 8. Printer Output and Alarm Input Wiring

Pelco Manual C1000M-B (1/96)

4.11.2 Alarm Trigger Dwell

4.12 Alarm Programming

Selection #2 enables you to program the amount of time

that the ALARM INPUT closure must be present in

order for the Inter-Check ICI1000S Series to recognize

it as a valid alarm condition. To program this option,

simply enter a suitable value between 000-255 seconds

for the minimum duration theALARM INPUT closure

is present. This ensures the Inter-Check ICI1000S Se-

ries unit will recognize it as a valid ALARM. The de-

fault value is set at 6 seconds.

NOTE:In the following examples, underlined

text designates the correct selection.

1. Since you want to turn ALARM INPUT “on”, se-

lect #1 under the ALARM INPUT PROGRAM

MENU.

2. Select #2 to turn this ALARM INPUT “on”

ALARM IN

4.11.3 Screen Link

1=OFF 2=ON

Selection #3 allows you to program the ALARM IN-

PUT TEXT to the video display. The ALARM INPUT

TEXT is surrounded by asterisks when this selection is

turned on. It captures your attention when an ALARM

INPUT condition has occurred. Simply select on or off

to display the text to the video screen.

3. Since you want to “send” the ALARM INPUT to

the ALARM OUTPUT, you have to turn ALARM

OUTPUT “on”. This is done by selecting #2 at the

next prompt:

TRIGGER ALARM OUT

1=OFF 2=ON

4.11.4 Auxiliary Print Link

4. Programming a 10 second closure time is done by

pressing #2 (ALARM TRIGGER DWELL) under

the ALARM INPUT PROGRAM MENU.

This selection allows you to program the auxiliary out-

put to print the alarm text. Select either 1 to turn off the

printer to the alarm text, or select 2 to turn the printer

on.

ALARM DWELL TIME IN SECONDS

(000-255) =?10

4.11.5 Alarm Text

Press 10, the appropriate time period, then ENT to

save.

This last selection displays an associated descriptor to

a specifiedALARM INPUT. The Inter-Check ICI1000S

Series allows you to program 12 characters including

spaces. This text will be displayed on the screen if the

SCREEN LINK is turned on and/or a printer if the

AUXILIARYPRINT LINK is turned on.As mentioned

earlier, the ALARM TEXT is surrounded by asterisks

on the printer or video screen.

5. Now link your ALARM INPUT to screen #1. Do

this by selecting #3 (SCREEN LINK) under the

ALARM INPUT PROGRAM MENU.

SCREEN DISPLAY

1=OFF 2=ON

NOTE: Each time you change any of the pa-

rameters just mentioned, the Inter-Check

ICI1000S Series updates current settings auto-

matically. The current settings can be viewed

by entering the ALARM INPUT PROGRAM

MENU.

Let’s say you want your Inter-Check ICI1000S Series

to activate an alarm condition when a cash register

drawer has been open for 10 seconds. After this alarm

has occurred, you want to print the text “REG. 1 OPEN”

on the screen as well as print this text on a printer via

the auxiliary port. You also wish to capture the action

on VCR tape.

Pelco Manual C1000M-B (1/96)

6. Print the ALARM INPUT text via auxiliary port.

Do this by selecting #4 (AUXILIARY PRINT

LINK) in the ALARM INPUT PROGRAM

MENU.

4.13 THE NV MEMORY WRITE

PROTECT SWITCH

Your new Inter-Check ICI1000S Series incorporates a

Non-Volatile (NV) type memory. This type of memory

does not require a battery to operate. Refer to Figure 5

for the location of this switch and note the locked and

unlocked positions. This switch must be positioned in

the UNLOCKED position if you intend on program-

ming the Inter-Check ICI1000S Series unit. If the switch

is in the LOCKED position and you try to enter pro-

gramming data, an “ERROR IN WRITING NV

MEMORY!!!” warning will be displayed on the moni-

tor screen. To allow programming, simply position the

write protect switch to the UNLOCKED position. When

programming is complete, position the switch to the

LOCKED position. This will protect your programming

from possible errors that may occur during AC power

fluctuations or complete Inter-Check ICI1000S Series

power loss.

AUX PRINT

1=OFF 2=ON

7. The descriptor will describe the type of action that

caused the alarm. To program the descriptor “REG.

1 OPEN”, enter #5 (ALARM TEXT) in the

ALARM INPUT PROGRAM MENU.

ENTER DATA WANTED UP TO 12

CHARACTERS.

(ESC) TO SKIP, (ENTER) TO ENTER,

(BS) TO BACKSPACE

ALARM IN

REG.1 OPEN

Press ENTER

8. The final display should look like this forALARM

1 IN:

Table 2. Label Descriptors

Descriptor

Display

ALARM IN DWELL : 10/ON/V1A1

= =>REG. 1 OPEN

Data

Video

DESCRIPTION:The alarm input is ON and

is currently being “sent” to both the video and

an auxiliary printer. Alarm occurs after a clo-

sure of 10 SECONDS with a descriptor dis-

playing REG.1 OPEN.

Exception

Auxiliary 1

Printer

PNTR

EALRM

Exception Alarm

Table 2 is used to identify the descriptors used through-

out the Inter-Check ICI1000S Series menu system.

Table 3. ICI1000S Series Pinouts

Color Pin #

Description

White

Black

Red

Program download input

Signal ground

RS232 current loop CHANNEL

INPUT

Green

Yellow

Blue

TTL printer output

ICI1000PIM input

Alarm input

Pelco Manual C1000M-B (1/96)

5.0 TROUBLESHOOTING

Symptom: Red power indicator light on back of

unit is not lit.

Symptom: System does not receive register data.

1. Make sure power supply is plugged in properly.

2. Make sure outlet is working properly.

1. Power down the PIM, then repower it. If you re-

ceive a display on your monitor with a register

model number, the unit is receiving data from the

PIM.

3. Ensure power supply is good (measure 5 volt out-

put).

2. Make sure the register model matches the number

displayed on the monitor.

4. Ensure that internal fuse is not blown.

3. Make sure the switch settings on your PIM are cor-

rect for your model register.

Symptom: External serial printer not operating

properly.

4. Verify that the communication setup and protocol

is accurate for your model register (non-PIM ap-

plications).

1. Ensure proper wiring to the Inter-Check unit.

2. Set printer parameters at 1200 baud, 8 bits, no par-

ity.

5. Check for proper wiring and hardware connections.

Symptom: ERROR IN NV MEMORY message

appears on the monitor.

6. Refer to DEFAULT LOAD procedures in Section

4.10.8 of this manual.

1. NV MEMORY write protect switch on the bottom

of the unit is in the locked position. Move to other

setting. (Refer to Section 4.2 and Figure 5.)

7. Refer to PIM INSTALLATION procedures sup-

plied with your ICI1000PIM or Appendix B of this

manual.

Symptom: RECEIVE ERROR, PLEASE

CHECK PARAMETERS is dis-

played on monitor.

Symptom: No text is displayed on the monitor.

1. Check camera and monitor connections.

1. Usually an indication of incorrect baud rate.

2. Verify that the Inter-Check’s power supply is con-

nected.

2. Also check protocol selection and communication

parameters.

3. Adjust potentiometers on bottom of the Inter-Check

unit.

Symptom: Inter-Check unit displays strange

character.

1. Check communication parameters and protocol.

2. Make sure baud rate is correct.

Symptom: Text vibrates on the monitor.

1. Adjust Vertical (V) on the bottom of the Inter-

Check unit.

2. Adjust Gain (G) on the bottom of the Inter-Check

unit.

Pelco Manual C1000M-B (1/96)

5.1 TROUBLESHOOTING FLOW CHART

Pelco Manual C1000M-B (1/96)

6.0 SPECIFICATIONS

MODELS

GENERAL

Ambient Operating

Temperature:

35° to 95°F (12.725° to 35°C)

ICI1000SI

Single register interface with inter-

nal keypad for programming; one (1)

alarm output and thirty (30) program-

mable exceptions

Dimensions:

1.5"H x 4.75"W x 8.75"L

(3.81 cm x 12.07 cm x 22.23 cm)

Weight:

2 lbs (.9 kg)

ICI1000SE

Same as ICI1000SI except with ex-

ternal keypad for programming

Construction:

Steel, black enamel

ELECTRICAL

Connectors:

Video

2 BNC

Input Voltage:

5 VDC ±3%

Alarm Out

One open collector output

Power Supply:

Input

Output

Rating:

NEMA 1

120 VAC @ 15 watts, 60 Hz

5 VDC @ 1 amp

Fuse Protection: 1 amp

Video Inputs:

One 75 ohm NTSC/PAL

Video Outputs: One 75 ohm NTSC/PAL

Alarm Outputs: One open collector output optically

isolated to 3000V

Internal Composite

Synchronization:

Standard

NTSC

Vertical 60 Hz @ 260 µs

Horizontal 15.36 KHz @ 4.38 µs

Optional PAL Vertical 50 Hz @ 260 µs

Horizontal 15.36 KHz @ 4.38 µs

Pelco Manual C1000M-B (1/96)

7.0 WARRANTY AND RETURN

INFORMATION

WARRANTY

RETURNS

Pelco will repair or replace, without charge, any merchandise proved

defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate

of shipment.

In order to expedite parts returned to the factory for repair or credit, please

call the factory at (800) 289-9100 or (559) 292-1981 to obtain an

authorization number (CA number if returned for credit, and RA number

if returned for repair).

Exceptions to this warranty are as noted below:

All merchandise returned for credit may be subject to a 20% restocking

and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the

assigned CA or RA number and freight should be prepaid. Ship to the

appropriate address below.

•

Five years on FT/FR8000 Series fiber optic products.

Three years on Genex^®Series products (multiplexers, server, and

keyboard).

Three years on Camclosure^®and fixed camera models, except the

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,

and MC3651H-2X camera models, which have a five-year warranty.

•

If you are located within the continental U.S., Alaska, Hawaii or Puerto

Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto

Rico and are instructed to return goods to the USA, you may do one of the

following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

•

Two years on standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and

DF5/DF8 Series fixed dome products.

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, includ-

ing when used in continuous motion applications.

Two years on Esprit^®and WW5700 Series window wiper (excluding

wiper blades).

•

Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura^™Series distributed

network-based video products.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

•

One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

If the goods are to be sent by a FREIGHT FORWARDER, send the goods

to:

Six months on all pan and tilts, scanners or preset lenses used in

continuousmotionapplications(thatis,presetscan,tourandautoscan

modes).

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

Pelco will warrant all replacement parts and repairs for 90 days from the

date of Pelco shipment. All goods requiring warranty repair shall be sent

freight prepaid to Pelco, Clovis, California. Repairs made necessary by

reason of misuse, alteration, normal wear, or accident are not covered

under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or

loss resulting from the specific use or application made of the Products.

Pelco’s liability for any claim, whether based on breach of contract,

negligence, infringement of any rights of any party or product liability,

relating to the Products shall not exceed the price paid by the Dealer to

Pelco for such Products. In no event will Pelco be liable for any special,

incidental or consequential damages (including loss of use, loss of profit

and claims of third parties) however caused, whether by the negligence

of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The

Dealer may also have additional rights, which are subject to variation from

state to state.

Ifawarrantyrepairisrequired,theDealermustcontactPelcoat(800) 289-

9100 or (559) 292-1981 to obtain a Repair Authorization number (RA),

and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall

under the warranty conditions stated above, please include a written

explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by

which the item was received by Pelco.

Pelco, the Pelco logo, Camclosure, Esprit,

Genex, Legacy, and Spectra are registered

trademarks of Pelco.

Endura and ExSite are trademarks of Pelco.

Pelco Manual C1000M-B (1/96)

APPENDIX A. HEXADECIMAL, DECIMAL AND BINARY CONVERSION TABLES

HEX

Decimal

Binary

HEX

Decimal

Binary

00000000

00000001

00000010

00000011

00000100

00000101

00000110

00000111

00001000

00001001

00001010

00001011

00001100

00001101

00001110

00001111

00010000

00010001

00010010

00010011

00010100

00010101

00010110

00010111

00011000

00011001

00011010

00011011

00011100

00011101

00011110

00011111

00100000

00100001

00100010

00100011

00100100

00100101

00100110

00100111

00101000

00101001

00101010

00101011

00101100

00101101

00101110

00101111

00110000

00110001

00110010

00110011

00110100

00110101

00110110

00110111

00111000

00111001

00111010

00111011

00111100

00111101

00111110

00111111

01000000

01000001

01000010

01000011

01000100

01000101

01000110

01000111

01001000

01001001

01001010

01001011

01001100

01001101

01001110

01001111

01010000

01010001

01010010

01010011

01010100

01010101

01010110

01010111

01011000

01011001

01011010

01011011

01011100

01011101

01011110

01011111

01100000

01100001

01100010

01100011

Pelco Manual C1000M-B (1/96)

HEX

Decimal

Binary

HEX

Decimal

Binary

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

01100100

01100101

01100110

01100111

01101000

01101001

01101010

01101011

01101100

01101101

01101110

01101111

01110000

01110001

01110010

01110011

01110100

01110101

01110110

01110111

01111000

01111001

01111010

01111011

01111100

01111101

01111110

01111111

10000000

10000001

10000010

10000011

10000100

10000101

10000110

10000111

10001000

10001001

10001010

10001011

10001100

10001101

10001110

10001111

10010000

10010001

10010010

10010011

10010100

10010101

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

10010110

10010111

10011000

10011001

10011010

10011011

10011100

10011101

10011110

10011111

10100000

10100001

10100010

10100011

10100100

10100101

10100110

10100111

10101000

10101001

10101010

10101011

10101100

10101101

10101110

10101111

10110000

10110001

10110010

10110011

10110100

10110101

10110110

10110111

10111000

10111001

10111010

10111011

10111100

10111101

10111110

10111111

11000000

11000001

11000010

11000011

11000100

11000101

11000110

11000111

Pelco Manual C1000M-B (1/96)

HEX

Decimal

Binary

HEX

Decimal

Binary

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

11001000

11001001

11001010

11001011

11001100

11001101

11001110

11001111

11010000

11010001

11010010

11010011

11010100

11010101

11010110

11010111

11011000

11011001

11011010

11011011

11011100

11011101

11011110

11011111

11100000

11100001

11100010

11100011

11100100

11100101

11100110

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

11100111

11101000

11101001

11101010

11101011

11101100

11101101

11101110

11101111

11110000

11110001

11110010

11110011

11110100

11110101

11110110

11110111

11111000

11111001

11111010

11111011

11111100

11111101

11111110

11111111

Pelco Manual C1000M-B (1/96)

APPENDIX B. ICI1000PIM SWITCH SETTINGS

Switches 4-8 These switches are used to set

Installation instructions for configuring the ICI1000PIM

interface module are provided under separate cover in

manual C1005M-D.

addresses of multiple PIM’s in a

Party-line system (ICI3000P unit).

The address selected normally

coincides with the actual cash

switch settings for corresponding

PIM addresses are shown below.

If for some reason this manual is not readily available,

refer to the following section to configure the switch

settings on the PIM interface module, if applicable to

your installation.

DESCRIPTION

SWITCH #

45678

POLLING PIM ADDRESS

(PIM # )

The following describes the DIP switch settings for

banks #1 and #2 on the ICI1000PIM interface module

(refer to Figure 9).

– – – – –

– – – – +

– – – + –

– – – + +

– – + – –

– – + – +

– – + + –

– – + + +

– + – – –

– + – – +

– + – + –

– + – + +

– + + – –

– + + – +

– + + + –

– + + + +

+ – – – –

+ – – – +

+ – – + –

+ – – + +

+ – + – –

+ – + – +

+ – + + –

+ – + + +

+ + – – –

+ + – – +

+ + – + –

+ + – + +

+ + + – –

+ + + – +

+ + + + –

+ + + + +

SWITCH BANK #1

The switches in this bank serve several different

purposes. Some basic features include Polling or Non-

polling selections, PIM addressing, clock signal

manipulation and ICI1000PIM graphics mode select.

Switch 1

Switch 2

Selects either a non-inverting or

inverted clock signal. The position

of this switch will vary between

registers. The switch setting varies

depending on the cash register

selected in the register decode list for

SWITCH BANK 2.

Selects either Polling or Non-polling

operation. Polling mode is used only

with the ICI3000P unit (Party-line

configuration) and is defined with a

[–] switch setting. Non-polling mode

should be selected when using Pelco’s

ICI2000D or ICI1000S series products

(stand-alone configuration). This

mode is defined with a [+] switch

setting.

Switch 3

This is a dual function switch

depending on the register type used.

In dot matrix cash register

applications, this switch selects either

NORMAL [–] or PIM GRAPHICS

[+] mode. Other applications will

choose between either receipt or

journal information for monitor

display. Function of this switch are

shown on the page 3. This switch is

normally in the CLOSED [–]

position.

NOTE:

[–] indicates an UP switch position

[+] indicates a DOWN switch position

In other words, a [–] means that you need to

slide the switch towards the [–] position on

the switch. Refer to the Figure 9 for a

definition of [–] and [+] positions.

Pelco Manual C1000M-B (1/96)

SWITCH BANK #2

X = POLLING/NON-POLLING

[+] NON-POLLING

This switch is dedicated to selecting which type of cash

below indicates the appropriate switch settings for a

particular cash register. The first three settings indicate

the appropriate settings for switches 1-3 on switch bank

#1. A more detailed description of these three switches

can be found at the beginning of this section.

[–] POLLING (Refer to page 35.)

R = RECEIPT

[–] or JOURNAL

[+] SELECT (Normally CLOSED [–])

G = GRAPHICS (Normally CLOSED [–])

+ = OPEN - FLIP THE SWITCH DOWN

IMPORTANT : The information below ap-

plies to the ICI1000PIM versions 4.02 and

greater only.

– = CLOSED - FLIP THE SWITCH UP

Type

Selection

Bank #1

Switch #

1 2 3

Bank #2

Switch #

1 2 3 4 5 6 7 8

CASIO TK-2000 Dot Matrix Printer .................................................................................. + X G

CASIO TK4300 Dot Matrix Printer ................................................................................... + X G

CASIO TK1200/TK2600/TK4600/CE4115/CE4630 Dot Matrix Printer ............................ + X G

CASIO TK2100/CE4530 Dot Matrix Printer ..................................................................... + X G

CASIO SA2000/2100 - Serial Printer ................................................................................ + X -

- - - + + + - -

- - - + + + + -

- - - + + - + +

- - - + + + - +

- - - + + + + +

DATA CHECKER ALPHA 2/3 Printer, ICL MT20001 With Alpha 2/3 Printer....................+ X R

DRESSER WAYNE Printer Serial .....................................................................................+ X R

+ - - + - - + -

+ - - - + + + -

ESPER 7100 Drum Printer................................................................................................ + X -

ESPER 7540/7810 Dot Matrix Printer .............................................................................. + X G

+ - - + + - - -

+ - - + + - - +

FUGITSU/ATRIUM Series with Bar 200 Printer ................................................................+ X R

GILBARCO TCR/G2 Parallel Printer ................................................................................. - X G

HUGEN SWEDA - SWEDA 5436 Serial Printer ................................................................ + X -

+ - - + - - - -

- - - - - - - -

+ - - - - + - -

IBM Model 1/2 Printer, IBM4683/4684 With Model 1 OR Model 2 Printer ........................+ X R

IBM Model 3&4 Printer, IBM4683/4684 IBM4693/4694 With Model 3 Printer...................+ X R

+ - - + - - + +

+ - - + - + - -

ICL-200 PTR, ICL-STORE MASTER 9518-200 ................................................................+ X R

ICL/DATA CHECKER MDL - 1600,1700,1800 Multidrop Connection............................... + X -

ICL/DTS 2000/2100/2200 EPSON 220-AF Dot Matrix Printer ........................................ + X G

ICL/DTS 2000/2100/2200 EPSON 220-F Dot Matrix Printer ........................................... + X G

+ - - + - - - -

+ - - + - - - +

- - + - - - - -

- - + - - - - +

JCM GOLD 2200 Drum Printer ......................................................................................... + X -

+ - - + - + + -

NCR 2127 With V3 MULTIFINCITON Printer - Serial ....................................................... + X -

NCR 2121 Printer - Serial ................................................................................................. + X +

NCR 2113 Printer - Serial ................................................................................................. + X -

NCR ANSWER Printer SINGLE

- - - + + - + -

- - - + + - - +

- - - + + - - -

NCR 1255/2140/2151/2152/2154/2157/2160/2552/2557

NCR 5300/SASI 1028/OLD STYLE Printer/MERIT REGISTER SYSTEMS ................. - X R

NCR ANSWER Printer DUAL - NCR 2126 ....................................................................... - X R

NCR 7150-5001 Printer (7000 SERIES REG.) .................................................................+ X R

- - - + - + - -

- - - + - + - +

- - - + - + + -

Pelco Manual C1000M-B (1/96)

Type

Selection

Bank #1

Switch #

1 2 3

Bank #2

Switch #

1 2 3 4 5 6 7 8

NIXDORF .......................................................................................................................... + X +

+ - - + + + + +

OMRON RS5550/RS5560 Dot Matrix Printer ................................................................... - X G

OMRON 4510, 4541 Dot Matrix Printer .............................................................................- X -

OMRON RS3410 Dot Matrix Printer ................................................................................. - X G

OMRON 4041, 4043 Dot Matrix Printer ............................................................................ + X -

- - + - - - + -

- - + - - - + +

+ - - - - + - +

- - + - - + - -

PANASONIC JS-6500 Dot Matrix Printer.......................................................................... - X G

RCALLEN RC204 Drum Printer ........................................................................................ + X -

SAMSUNG 4900, 4915, 4950 Dot Matrix Printer .............................................................. - XG

SANYO ECR 580,690,720 EPSON 220F Dot Matrix Printer ........................................... + X G

+ - - + + - + +

+ - - + - + + +

- - + - - + + -

+ - - + + - + -

SHARP A430 DP630 Dot Matrix Printer ........................................................................... - X G

SHARP 2381/2391 Drum Printer ...................................................................................... + X +

SHARP 3230/3231/3240/3241/4230/4231 Dot Matrix Printer........................................... - X G

SHARP 3100/3100S/3110/3250/3252/3300/3310/3311 Dot Matrix Printer ...................... - X G

SHARP 4230, 4231 Dot Matrix Printer .............................................................................. - XG

SHARP 2595 Drum Printer ............................................................................................... + X +

SHARP 2385/2386/2395/2396 Drum Printer .................................................................... + X +

SHARP A550 Dot Matrix Printer ...................................................................................... + X G

SHARP 3220 Dot Matrix Printer ........................................................................................ - X G

SHARP 2540/2590/2590S Drum Printer ........................................................................... + X +

- - + - - + - +

- - - - - - + -

- - - - - + - +

- - - - - + + -

+ - + - - - - -

- - - - - + - -

- - - - - - + +

- - - - + - - -

- - - - - + + +

- - - - - - - +

SWEDA 2810/OMRON RS14-30 (USA Type) Drum Printer ............................................. + X +

SWEDA 2810/OMRON RS14-40 (USA Type) Drum Printer ............................................. + X +

SWEDA 2810/OMRON RS14-40 (European Type) Drum Printer..................................... + X +

SWEDA 2820/OMRON XXXX-XX (USA Type) Drum Printer ........................................... + X +

SWEDA 2860 .................................................................................................................... - X G

+ - - - - - - -

+ - - - - - - +

+ - - - - - + -

+ - - - - - + +

+ - - + + + - +

TEC 136/141/191/196 DISPLAY....................................................................................... - X +

TEC 206/216/227/230/290 DISPLAY................................................................................ - X +

TEC 141 Printer Drum Printer ........................................................................................... + X +

TEC 132/145 Drum Printer................................................................................................ + X -

TEC 2200/2300/2600 DPR-610/620 Dot Matrix Printer ................................................... + X G

TEC 2200/2300/2600 DPR-630 Dot Matrix Printer .......................................................... + X G

TEC 2200/2300/2600 DPR-61A Dot Matrix Printer.......................................................... + X G

TEC 1050/1060/1100/1190 DPR-710 Dot Matrix Printer .................................................. - X G

TEC 1050/1060/1100/1190 DPR-730 Dot Matrix Printer .................................................. - X G

TEC 1400/1600/1700/1900/FDS-30 DPR-370/374 Dot Matrix Printer............................. + X G

TEC 1400/1600/1700/1900/FSD-30 DPR-370S Dot Matrix Printer ................................. + X G

TEC FT77 Printer - Serial Interface................................................................................... + X -

- - - - + - - +

- - - - + - + -

- - - - + - + +

+ - - + - + - +

- - - - + + - -

- - - - + + - +

- - - - + + + -

- - - - + + + +

- - - + - - - -

- - - + - - - +

- - - + - - + -

- - - + - - + +

TOKHEIM.......................................................................................................................... - X R

+ - - + + + - -

Pelco Manual C1000M-B (1/96)

Figure 9. ICI1000PIM Switch Settings

ICI1000PIM INSTALLATION/

TROUBLESHOOTING GUIDELINES

NOTE: In rare instances when connecting a

PIM directly to an ICI1000S unit is desired

(without the use of a wiring kit), the data cable

will need to be modified.

Listed below are some simple troubleshooting steps at

your disposal. Following these steps will ensure that

your Inter-Check P.O.S. unit is communicating correctly

with your ICI1000PIM module.

To modify the cable:

a. Slit the gray insulation jacket of the data cable

and expose the internal wires.

1. Always execute a PIM DEFAULT LOAD (DL) on

your Inter-Check unit. Pelco suggests the use of

the Default Load even if your installation does not

require a PIM module. The Default Load sets all

Inter-Check communication parameters to the spe-

cific values needed to communicate with your

ICI1000PIM module.

b. Cut the red and green wires and remove a

small section of each to prevent against acci-

dental contact.

4. Install the PIM into the cash register. Refer to the

installation instructions included with your particu-

lar cash register interface.

2. Select cash register options using the switch banks

on your PIM. Refer to previous pages for more

information.

5. Power-up PIM and look for prompt again.

3. Utilizing the wiring kit, perform a bench test by

connecting the PIM to the Inter-Check unit and then

power up the PIM. Upon power-up, you should

see a prompt scroll across the monitor which

matches your register type. APIM version number

will also be displayed. If this prompt appears on

the monitor, the Inter-Check unit and PIM are com-

municating properly.

6. Power-up cash register and test for proper opera-

tion.

Now, install the wiring kit and connect the PIM

according to the proper wiring shown in Figure 2

and power up the PIM again. If the wiring is cor-

rect, you should see the prompt explained in step

#3.

Pelco Manual C1000M-B (1/96)

Pelco

3500 Pelco Way, Clovis, CA 93612-5699 (209) 292-1981 • (800) 289-9100

FAX (800) 289-9150 or (209) 292-3827

(Product specifications subject to change without notice.)

C1000M-B

Pelco Manual C1000M-B (1/96)

Pelonis Electric Heater HO 202C User Manual
Philips Battery Charger SCB2100NB User Manual
Philips Blu ray Player BDP7100 User Manual
Philips Security Camera BB HCA10CE User Manual
Philips Video Gaming Accessories SGC5102BD User Manual
Polaris Offroad Vehicle 200 Quadricycle User Manual
Polaris Offroad Vehicle 500 X2 User Manual
Powermate Portable Generator PC0473503 User Manual
Primera Technology Network Card DUP 07 User Manual
PYLE Audio Car Stereo System PLVSR7IR User Manual