®
00974
DF8 Series
Pendant Dome
Maintenance/
Service Manual
C2433SM-A (8/02)
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
6. Do not install near any heat sources, such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
9. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, the apparatus does not operate
normally, or the apparatus has been dropped.
10. To reduce the risk of shock, do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.
11. The installation method and materials should be capable of supporting four times the
weight of the unit and equipment.
12. Only use replacement parts recommended by Pelco.
13. After replacement/repair of this unit’s electrical components, conduct a resistance
measurement between line and exposed parts to verify the exposed parts have not
been connected to line circuitry.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous volt-
age constituting a risk of electric shock is
present within this unit.
C A U T I O N :
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that there are impor-
tant operating and maintenance instructions
in the literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
Pelco Manual C2433SM-A (8/02)
3
DESCRIPTION
DF8 Series pendant domes are discreet surveillance domes that are designed for indoor or
outdoor use.
MODELS
DF8-PB-0
Indoor, black, fixed mount pendant dome, black opaque lower dome
with smoked viewing window (1/2 f-stop of light loss)
DF8-PB-1
DF8-PB-2
DF8-PB-3
DF8-PG-0
Same as DF8-PB-0, except clear viewing window (virtually no light loss)
Same as DF8-PB-0, except chrome lower dome (2 f-stops of light loss)
Same as DF8-PB-0, except gold lower dome (2 f-stops of light loss)
Indoor, gray, fixed mount pendant dome, black opaque lower dome
with smoked viewing window (1/2 f-stop of light loss)
DF8-PG-1
DF8-PG-2
DF8-PG-3
DF8-PG-E0
Same as DF8-PG-0, except clear viewing window (virtually no light loss)
Same as DF8-PG-0, except chrome lower dome (2 f-stops of light loss)
Same as DF8-PG-0, except gold lower dome (2 f-stops of light loss)
Outdoor, gray, fixed mount pendant dome, heater and blower, black
opaque lower dome with smoked viewing window (1/2 f-stop of light loss)
DF8-PG-E1
Same as DF8-PG-E0, except clear viewing window (virtually no light loss)
MAINTENANCE
Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch
the surfaces of the dome.
Exterior Surface – Clean the dome’s exterior surface with a nonabrasive cleaning cloth
and cleaning agent that is safe for acrylic plastic. Either liquid or spray cleaner/wax suitable
for fine furniture is acceptable.
Interior Surface (Except Chrome or Gold) – Clean the same as the exterior surface.
Interior Surface (Chrome or Gold) – The inside surface of a chrome or gold dome is
easily scratched. Use the following precautions to maintain the dome’s surface.
1. Always handle the dome from the outside of its circular flange.
2. Never touch the coated inside surface. The acid in your fingerprints will eventually
etch the coating if the fingerprints are not carefully removed according to the recom-
mended cleaning procedure in item 5.
3. If dust or other contaminants accumulate on the dome’s interior, remove the debris
with compressed air. Compressed air cans are available from photographic equipment
or electronic supply dealers.
4. If heavy residue accumulates and cannot be removed with air pressure, rinse with
water and immediately dry with air pressure so that water spots will not remain. Avoid
wiping the coated surface with direct hand pressure – it will easily abrade unless
extreme care is taken. Once scratched, the dome cannot be recoated.
5. If internal wiping is necessary, avoid hand rubbing. Instead, make a wick as follows:
Use a very soft paper towel. Roll a section into a tightly wound tube. Tear the tube in
half, and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with
water. Hold the dome with its opening facing downward and wipe the interior of the
dome with the wet end of the wick. Use a circular motion, starting from the outside and
spiraling into the center. Use a new wick for each two passes over the dome.
4
Pelco Manual C2433SM-A (8/02)
EXPLODED ASSEMBLY DIAGRAMS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
13
15
14
15
16
17
18
14
Figure 1. Exploded Assembly Diagram–DF8 Pendant Models
Table A. Exploded Assembly Parts List–DF8 Pendant Models
Item
Qty
Description
Part Number
1
3
Screw, 6-32 x 5/16", pan head, Phillips, gray, with plastic washer
(outdoor models only)
Internal tooth lock washer, #6 (outdoor models only)
Sun shield (outdoor models only)
Top mount, black
Top mount, gray
Gasket
Internal tooth lock washer, #8
Screw, 8-32 x 3/8", pan head, Phillips
Back box, black
Back box, gray
Base plate
Internal tooth lock washer, #8
Nut, 8-32
Tilt table support leg
Fender washer, 1/4"
Split lock washer, 1/4"
Nut, 1/4-20
Tilt table
Flat washer, 3/16"
ZH6-32X.312GRAY
2
3
4
3
1
1
ZH6LWSIS
MF02-3020-007
MF03-7060-174
MF02-7060-174
70610012
5
6
7
8
1
3
3
1
ZH8LWSIS
ZH8-32X.375SPP
MF03-3021-005
MF02-3021-005
PDF54000COMP
ZH8LWSIS
ZH8-32NUTSH
MF03-3020-002
ZH25X1.50X625
ZH1/4LWSSL
ZH1/420NUTCH
MF03-3021-003
ZH260X562X65C
ZH1/420X.500CH
9
1
3
3
1
2
3
2
1
1
1
1
10
11
12
13
14
15
16
17
18
NS
Screw, 1/4-20 x 1/2"
Trim leash assembly attached to side of back box
Leash
7061005
Internal tooth lock washer, #6
Nut, 6-32
Nylon cable clamp (outdoor models only)
ZH6LWSIS
ZH6-32NUTSH
ZH8911
NS = Not shown
Pelco Manual C2433SM-A (8/02)
5
2
3
4
5
7
1
6
7
6
01145
Figure 2. Exploded Assembly Diagram–Heater and Fan Assembly (Outdoor Models Only)
Table B. Exploded Assembly Parts List–Heater and Fan Assembly (Outdoor Models Only)
Item
Qty
Description
Part Number
1
2
3
4
5
6
7
NS
1
1
2
2
2
7
7
1
Circuit board, fan rectifier
Spacer, 3/16" diameter x .125", #4
Fan/heater shroud
Heater pad, 24 VAC, 15W
Fan, 12 VDC, .7W, 7 cfm
Nut, 4-40
Internal tooth lock washer, #4
Power/heater circuit board on side of back box
Includes thermostat
PCB9000277BASSY
SPA9015
MF01-1041-013
HT01-0321-0202
ZH65-1240-1044
ZH4-40NUTSH
ZH4LWSIS
PCB9000300ASSY
On at 40°F (4°C)
Off at 60°F (16°C)
Spacer, .250" outside diameter x .125", #6
Internal tooth lock washer, #6
Nut, 6-32
SPA8500
ZH6LWSIS
ZH6-32NUTSH
NS = Not shown
6
Pelco Manual C2433SM-A (8/02)
1
3
2
4
5
6
7
9
8
10
01146
Figure 3. Exploded Assembly Diagram–Pendant Lower Dome
Table C. Exploded Assembly Parts List–Pendant Lower Dome
Item
Qty
Description
Part Number
1
5
5
6
1
Screw, 6-32 x 1/4", pan head, Phillips (indoor models only)
Screw, 6-32 x 3/8", pan head, Phillips (outdoor models only)
Internal tooth lock washer, #6
DF8 Heater Ring Assembly (outdoor models only)
24 VAC, 60W
ZH6-32X.250SPP
ZH6-32X.375SPP
ZH6LWSIS
2
3
3023-004A
Includes thermostat
On at 70°F (21°C)
Off at 85°F (29°C)
4
5
6
7
8
1
1
1
1
2
Screw, 6-32 x 1/4", pan head, Phillips
Lower dome retainer
O-ring
ZH6-32X.250SPP
MF00-3020-006
ZH69-0105-2756
GS01-0002-0430
ZH6-32X.312GRAY
Trim ring gasket
Screw, 6-32 x 5/16", pan head,
Phillips, gray, with plastic washer
Trim ring, black
9
1
1
MF03-3020-010
MF02-3020-010
80810015-00
80810015-01
80810011-2
Trim ring, gray
10
Acrylic dome, black opaque with smoked viewing window
Acrylic dome, black opaque with clear viewing window
Acrylic dome (chrome)
Acrylic dome (gold)
80810011-3
Pelco Manual C2433SM-A (8/02)
7
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date
C2433SM 9/01
C2433SM-A 8/02
Comments
Original version.
Added certifications. Revised Important Safeguards and Warnings.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
© Copyright 2002, Pelco.
All rights reserved.
8
Pelco Manual C2433SM-A (8/02)
|