Always there to help you
Register your product and get support at
ORT7500
Question?
Contact
Philips
User manual
Contents
1 Safety
2
2
11 Product information
General information
Tuner
16
16
16
16
16
16
Important notes for users in the U.K.
Amplifier
Speakers
Bluetooth
2 Your DAB+ Radio
Introduction
4
4
4
5
What's in the box
Overview of the product
12 Troubleshooting
General
17
17
17
3 Get started
Connect power
Turn on
6
6
6
6
About Bluetooth connection
Set the clock
13 Notice
18
18
18
18
18
Compliance
Care of the environment
Trademark notice
Copyright
4 Listen to FM radio stations
Search for a radio station automatically
Store radio stations automatically
Program radio stations manually
Display RDS information
7
7
7
8
8
9
Adjust FM settings
5 Listen to DAB radio stations
For the first time use
10
10
10
10
11
Program radio stations
Display DAB information
Use DAB menus
6 Use system menus
Check the current software version
Reset the product
12
12
12
12
Upgrade the software
7 Listen to an external device
8 Play audio via Bluetooth
9 Charge your devices
10 Adjust the volume
13
14
15
15
EN
1
•
•
This product shall not be exposed to
dripping or splashing!
Do not place any sources of danger on this
product (e.g. liquid filled objects, lighted
candles).
Never place the product or any objects
on power cords or on other electrical
equipment.
If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
Only use attachments/accessories specified
by the manufacturer.
1 Safety
Read and understand all instructions before you
use this product. If damage is caused by failure
to follow the instructions, the warranty does
not apply.
•
•
Risk of electric shock or fire!
•
Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Philips Consumer
Care to have the product checked before
use.
•
Risk of overheating!
•
Never install this product in a confined
space.Always leave a space of at least four
inches around the product for ventilation.
Make sure that curtains or other objects
never cover the ventilation slots on the
product.
•
Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
•
•
•
Never insert objects into the ventilation
slots or other openings on the product.
Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Note
• The type plate is located on the back of the product.
•
•
•
Disconnect the product from the power
outlet before lightning storms.
When you disconnect the power cord,
always pull the plug, never the cable.
Never remove the casing of this product.
Important notes for users in
the U.K.
Risk of short circuit or fire!
Mains fuse
•
Before you connect the product to the
power outlet, make sure that the power
voltage matches the value printed on the
back of the product. Never connect the
product to the power outlet if the voltage
is different.
This information applies only to products with a
UK mains plug.
This product is fitted with an approved molded
plug. If you replace the fuse, use one with:
•
•
•
the ratings shown on the plug,
a BS 1362 approval, and
the ASTA approval mark.
•
•
Never expose the product to rain, water,
sunshine, or excessive heat.
Avoid force coming onto power plugs.
Loose power plugs can cause arcing or fire.
Contact your dealer if you are not sure about
what type of fuse to use.
Risk of injury or damage to the product!
2
EN
Caution:To conform with the EMC directive
(2004/108/EC), do not detach the plug from
the power cord.
How to connect a plug
The wires in the power cord are colored as
follows: blue = neutral (N), brown = live (L).
If the colors do not correspond with the colors
on your plug, identify the terminals in your plug
as follows:
1
2
3
Connect the blue wire to the terminal
marked N or colored black.
Connect the brown wire to the terminal
marked L or colored red.
Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
colored green (or green and yellow).
Before you replace the plug cover, make sure
that the cord grip is clamped over the sheath
of the cable and not just over the two wires in
the cable.
Copyright in the U.K.
Recording and playback of material may require
consent. see Copyright Act 1956 andThe
performer's Protection Acts 1958 to 1972.
EN
3
2 Your DAB+
Radio
What's in the box
Check and identify the contents of the package:
a Digital radio
b User manual
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
c Audio in cable
d AC power cord
e UK power cord
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
Introduction
With this product, you can:
•
listen to FM radio stations (RDS
supported),
OR7200
•
•
listen to DAB radio stations,
listen to audio from an external device
through the AUDIO-IN socket,
listen to audio from an external device via
Bluetooth connection.
User Manual
•
4
EN
•
•
Press to switch the system between
standby mode and normal mode.
Overview of the product
Turn to adjust the volume.
i
h
a
b
g
f
e
c
d
n
j
k
m
l
e
a INFO
•
•
•
In FM mode, turn to tune to a radio
station manually.
•
Press repeatedly to display available
information.
Turn to toggle through FM or DAB
menus.
b SCAN
•
Press to activate the search for the
Under FM or DAB menus, press to
enter lower level menus or confirm an
option.
next strong FM radio station.
•
Press and hold to activate the
automatic search for and storage of
FM radio stations.
f PRESET
•
Turn to select a preset radio station.
g PROGRAM
•
Press to activate the programming of
radio stations.
•
Turn to switch the system from
standby mode to normal mode.
h MENU
d
EN
5
•
Press to enter or exit FM or DAB
menus.
3 Get started
i LCD screen
j AC MAIN~
Always follow the instructions in this chapter in
sequence.
•
Connect to the AC power cord.
k AUDIO IN
•
Connect to an external device by an
audio in cable.
Connect power
l DAB SOFTWARE
•
The socket for firmware upgrade
m
•
USB socket,charge the device only
n Antenna
Connect the AC power cord to the AC
MAIN~ socket and then to the wall outlet.
Turn on
Press the knob or turn the SOURCE knob.
» The product switches to the last
selected source.
•
To switch the product to standby
mode, press the knob again.
Set the clock
1
In standby mode, press and hold the
knob for 2 seconds.
»
(12-hour time format) or
(24-hour time format) blinks.
2
3
Turn the
and then press the
» Hour digits blink.
knob to select a time format,
knob to confirm.
Turn the
press the
knob to set the hour, and then
knob to confirm.
6
EN
» Minute digits blink.
4 Listen to FM
radio stations
4
5
6
Turn the
Press the
Turn the
knob to set the minute.
knob to confirm.
knob to select whether to
synchronize the DAB clock and then press
the knob to confirm
1
2
Turn the SOURCE knob to switch the
product to FM mode.
Search for radio stations automatically or
manually.
Search for a radio station
automatically
Press SCAN to activate the auto search.
Note
• For optimal reception, fully extend the antenna and
adjust its position.
• You can store a maximum of 30 FM radio stations.
» After a strong radio station is detected,
the search stops and the radio station
is broadcast.
Search for a radio station
automatically
Press SCAN to activate the auto search.
» After a strong radio station is detected,
the search stops and the radio station
is broadcast.
Store radio stations
automatically
Press and hold SCAN to activate the auto
search.
» After the search is complete, the first
stored radio station is broadcast.
•
To tune to a stored radio station, turn
the PRESET knob until its frequency is
displayed.
EN
7
Display RDS information
Radio Data System (RDS) is a service that
allows FM stations to transmit additional
information.When you tune to an FM radio
station that transmits RDS signals, the station
name is displayed.
2 sec.
1
2
Tune to an RDS station.
Press INFO repeatedly to scroll through
the following information (if available):
•
Radio text
•
Program type such as [NEWS] (news),
[SPORT] (sport), [POP M] (pop
music)...
•
•
•
•
Program service
Mono/Stereo
Time
Date
RDS program types
Program radio stations
manually
Pro-
gram
type
Description
Program Descrip-
type tion
1
2
Tune to a radio station.
NEWS News services
FINANCE Finance
Politics and currentCHIL- Children's
programs
Press the PROGRAM button to activate
the programming.
AF-
FAIRS affairs
DREN
3
4
Turn the
sequence number.
knob to select a preset
INFO Special informationSOCIAL Social af-
programs
SPORT Sports
EDU- Education and
fairs
RELIGIONReligion
PHONE Phone in
Press the
knob to confirm.
» The radio station is stored with the
selected sequence number.
CATE advanced training IN
DRA- Radio plays and TRAVEL Travel
5
Repeat steps 1-4 to program more radio
stations.
To tune to a preset radio station, turn
the PRESET knob until its frequency is
displayed.
MA
literature
CUL- Culture, religion LEISURE leisure
TURE and society
•
SCI-
Science
JAZZ
Jazz Music
ENCE
VAR- Entertainment
IED programs
POP M Pop music
COUN- Country
TRY Music
NATION National
Music
Note
• If you store a radio station with the sequence number
of another one, the earlier one is overwritten.
M
ROCK Rock music
M
OLDIES Oldies
Music
8
EN
•
: Convert stereo signals
to monophonic output even if the
station transmits strong stereo audio
signals.
MOR Light music
M
LIGHT Light classical
FOLK M Folk Music
DOCU- Documen-
M
music
MENT
tary
3
Press the
knob to confirm the option.
CLAS- Classical music
SICS
TEST
AlarmTest
OTH- Special music
ER M programs
ALARM Alarm
System menus
WEATHER
Weather
1
Press the
Turn the
For details, refer to the section 'Use
knob to access system menus.
knob to select a sub-menu.
Adjust FM settings
2
•
1
In FM mode, press MENU to access FM
menus.
system menus'.
2
Turn the
menus.
knob to toggle through the
Scan setting
1
2
Press the
knob to access sub-menus.
Turn the
•
knob to select an option.
: Search for strong
stations only.
•
: Search for all stations
no matter whether the signal strength
of a station is strong or weak.
3
Press the
knob to confirm the option.
Audio setting
1
2
Press the
knob to access sub-menus.
Turn the
•
knob to select an option.
:Allow stereo
output even if the station transmits
weak stereo audio signals.
EN
9
•
H:The station is one of your 10 favorite
stations.
?:The station is unavailable or inactive.
:The station is a primary station with
secondary service.
5 Listen to DAB
radio stations
•
•
•
:The station is a secondary station.
Note
Program radio stations
• For optimal reception, fully extend the antenna and
adjust its position.
• You can program a maximum of 30 DAB radio stations.
for applicable DAB radio frequencies in your area.
1
2
Tune to a DAB radio station.
Press PROGRAM to activate the
programming.
3
4
Turn the
sequence number.
knob to select a preset
Press the
knob to confirm.
For the first time use
» The radio station is stored with the
selected sequence number.
1
2
3
Turn the SOURCE knob to switch the
product to DAB mode.
5
Repeat steps 1-4 to program more radio
stations.
To tune to a preset radio station, turn
the PRESET knob until its frequency is
displayed.
Turn the
knob until the [Full scan]
•
menu is displayed.
Press the
knob to activate the
automatic search.
» This product automatically stores radio
stations with sufficient signal strength.
Note
» After the search is complete, the
first stored radio station is broadcast
automatically.
• If you store a radio station with the sequence number
of another one, the earlier one is overwritten.
4
Turn the
then press the
knob to select a station, and
knob to start listening.
Display DAB information
Tip
On the display of DAB broadcasting, the first
line shows station name, and the second line
shows the service information for the current
station.
• You can re-scan to update the list of stored stations
(see "Use DAB menus" > "Re-scan for stations").
• You can tune to a station manually (see "Use DAB
menus" > "Tune to a station manually").
Press INFO repeatedly to cycle through the
following information (if available).
•
•
•
•
•
Dynamic label segment (DLS)
Signal strength
Program type (PTY)
Ensemble name
About special symbols
Some symbol may be displayed before the
name of a station.
Frequency
10 EN
•
•
•
•
Signal error rate
Bitrate codec
Time
Tune to a station manually
With this feature, you can tune to a specific
channel/frequency manually. In addition to
antenna orientation for better radio reception,
the optimal reception can also be obtained with
this feature.
Date
Use DAB menus
1
In DAB mode, press MENU to access the
DAB menus.
2
Turn the
menus.
knob to toggle through the
1
2
Press the
knob to access the station list.
knob to select a station from
Turn the
5A to 13F.
Tune to a stored station
3
Press the
knob to confirm the option.
1
Press the
stored stations.
If no DAB station is stored, the product
starts automatic search.
knob to access the list of
•
DRC (Dynamic Range Control)
DRC adds or removes a degree of
compensation for the differences in the dynamic
range between radio stations.
2
3
Turn the
Press the
knob to select a station.
knob to start listening.
Re-scan for stations
Full scan is used to perform a wide range
search for DAB radio stations.
1
2
Press the
menus.
knob to access the sub-
Turn the
knob to select an option. (The
asterisk behind the option indicates the
current setting.)
•
: No compensation applied.
Press the
knob to start scanning for available
DAB stations.
•
: Medium compensation
applied.
applied.
» After the scanning is complete, the first
detected station is broadcast.
•
: Maximum compensation
3
Press the
knob to confirm the option.
EN 11
Remove invalid stations
6 Use system
menus
This option lists active stations and removes any
stations that are in the list but have no service
in your area. In front of the station name of an
invalid station, a question mark (?) is displayed.
Use the system menus to
•
check the version of current software of
this product,
•
•
upgrade the software, and
reset the product to factory default status.
1
2
Press the
menus.
knob to access the sub-
Turn the
•
knob to select an option.
: Return to the previous menu.
Check the current software
version
•
: Remove invalid stations from
the station list.
3
Press the
knob to confirm the option.
System menus
Press the
knob to display the version of
current software.
Reset the product
1
Press the
Turn the
For details, refer to the section 'Use
knob to access system menus.
knob to select a sub-menu.
2
•
system menus'.
1
2
Press the
knob to display the options.
Turn the
•
knob to select an option.
: Return to the previous menu.
•
: Reset the product to factory
default status.
3
Press the
knob to confirm the option.
Upgrade the software
12 EN
7 Listen to an
external device
1
2
Search for support information about
your product with "ORT7500/12" as the
keyword.
» When an upgrade packet is available,
the link of "Firmware Upgrade
Readme File" is accessible.The exact
wording of this link name may vary in
different languages.
You can also listen to an external audio device,
for example, MP3 player, through this product.
1
2
Turn the SOURCE knob to switch the
product to AUDIO IN mode.
Connect the audio in cable to
•
the AUDIO IN socket on the back
panel of this product, and
•
the headphone jack on the external
device.
3
4
5
Click the link of "Firmware Upgrade
Readme File".
3
Play the external device (refer to its user
manual).
Read and understand the instructions on
software upgrade.
Follow the instructions to complete the
upgrade.
EN 13
2
3
On your device, search for Bluetooth
devices. In the device list, select ORT7500.
8 Play audio via
Bluetooth
•
If a message prompts for the
permission for Bluetooth connection
with ORT7500, confirm it.
» If the connection succeeds, [BT
Connected] is displayed on the LCD
display of this product.
With this product, you can stream audio from a
Bluetooth player.
Play a track on the connected device.
An application Philips DigitalRadio is available
on Apple App Store and Google Play.To fully
enjoy features of this product, download and
install the application to your smart device.
•
To pause or resume play, press
To skip to the previous or next track,
press
.
•
/
.
Note
• Philips does not guarantee the compatibility with all
Bluetooth devices.
• Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
• The product can memorize a maximum of 4 paired
devices.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• The operational range between this system and a
Bluetooth device is approximately 10 meters (30 feet).
• Any obstacle between this system and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
Note
•
/
If the connected Bluetooth device supports the
Advanced Audio Distribution Profile (A2DP), you can
listen to tracks that are stored on the device through
the system.
• If the device also supports the AudioVideo Remote
Control Profile (AVRCP), you can control play on this
product.
• If the connected device does not support the AVRCP,
control play on the connected device.
1
Turn the SOURCE knob to switch the
product to BT mode.
» If no Bluetooth device is connected,
[Bluetooth No Connection] (No
Bluetooth connection) scrolls.
14 EN
9 Charge your
devices
10 Adjust the
volume
Connect your device to the USB
socket on
Turn the knob.
the back of the product.
» Once the device is recognized, the
charging starts.
Note
• Philips does not guarantee the compatibility of this
product with all devices.
• The USB
socket is for charging only.
EN 15
Frequency Response
60 Hz - 16 kHz,
±3 dB
> 65 dB
11 Product
information
Signal to Noise Ratio
Aux Input
0.5V RMS 20 kohm
Note
• Product information is subject to change without prior
notice.
Speakers
Speaker Impedance
Speaker Driver
Sensitivity
6 ohm
2 X 3" full range
>82 dB/m/W
General information
AC Power Rating
100-240V~,
50/60 Hz
Bluetooth
Operation Power
Consumption
Standby power consumption
Dimensions (Main Unit)
15 W
Communication Bluetooth Standard version
system
Output
2.0
< 1 W
325 x 175 x
167 mm
Bluetooth Standard Power
Class 2
Line of sight approx. 10m
Maximum
communication (30 feet)
range
Weight (Main Unit)
3.5 kg
Frequency band 2.4 GHz band (2.4000 GHz
- 2.4835 GHz)
Tuner
Tuning Range
Compatible
Bluetooth
profiles
Advanced Audio Distribution
Profile (A2DP)
FM: 87.50 - 108.00
MHz;
AudioVideo Remote
Control Profile (AVRCP)
SBC (Sub Band Codec)
DAB: 174.928-
239.200 MHz
50 kHz
Supported
codecs
Tuning grid
SBC (Sub Band Codec)
- Receive
-Transmit
DAB sensitivity
(EN50248)
Total Harmonic
Distortion
< -95 dbm
< 2%
Signal to Noise Ratio
> 50 dB
Number of preset radio
stations
30 (FM), 30 (DAB)
Amplifier
Rated Output Power
10 W x 2 RMS
16 EN
•
•
Power has been interrupted, or the AC
power adaptor has been disconnected.
Set the clock again.
12 Troubleshooting
Warning
• Never remove the casing of this product.
About Bluetooth connection
Music playback is unavailable on this product
even after successful Bluetooth connection.
To keep the warranty valid, never try to repair
the product yourself.
•
The device cannot be used with this
product to play music.
If you encounter problems when using this
product, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the product is nearby and the
model number and serial number are available.
The audio quality is poor after connection
with a Bluetooth-enabled device.
•
The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between.
Cannot connect with this product.
General
•
The device does not support the profiles
required for this product.
No power
•
The Bluetooth function of the device is
not enabled. Refer to the user manual of
the device to find out how to enable the
function.
•
Make sure that the AC power cord is
properly connected.
•
Make sure that there is power at the AC
power outlet.
•
•
This product is not in the pairing mode.
This product is already connected with
another Bluetooth-enabled device.
No sound
•
•
Adjust the volume.
Disconnect that device and then try again.
When listening to an external device, make
sure that the external device is not muted.
The paired mobile device connects and
disconnects constantly.
No response from the product
•
The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between.
•
•
Make sure that the power is available.
Turn off the product, and then turn it on
again.
•
Some mobile phones may connect and
disconnect constantly when you make
or end calls.This does not indicate any
malfunction of this product.
Poor radio reception
•
Due to the interference from other
electrics or building obstacles, the signals
become weak. Move the product to a
place free of interference.
•
For some devices, the Bluetooth
connection may be deactivated
automatically as a power-saving feature.
This does not indicate any malfunction of
this product.
•
Make sure that the antenna is fully
extended.Adjust the position of the
antenna.
Clock setting is erased.
EN 17
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local
separate collection system for electrical and
electronic products.
13 Notice
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
Compliance
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
This product complies with the radio
interference requirements of the European
Community.
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
A copy of the EC declaration of Conformity
is available in the Portable Document Format
(PDF) version of the user manual at www.
philips.com/support.
Trademark notice
This is CLASS II apparatus with double
insulation, and no protective earth provided.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by WOOX
Innovations is under license.
Care of the environment
Copyright
2013 © WOOX Innovations Limited.All rights
reserved.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Specifications are subject to change without
notice.WOOX reserves the right to change
products at any time without being obliged to
adjust earlier supplies accordingly.
18 EN
EN 19
20 EN
EN 21
Specifications are subject to change without notice
All registered and unregistered trademarks are property of their respective owners.
2013 ©WOOX Innovations Limited.All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by
WOOX Innovations Limited under license from Koninklijke Philips N.V.
ORT7500_10_UM_V2.0
|