INTEGRATED CIRCUITS
DATA SHEET
TDA6101Q
Video output amplifier
1995 Feb 07
Preliminary specification
Supersedes data of November 1991
File under Integrated Circuits, IC02
Philips Semiconductors
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
BLOCK DIAGRAM
supply voltage
input HIGH
feedback
output
6
9
7 V
MIRROR
MIRROR
FOLLOWERS
cathode
transient
7
V
bias
output
C
par
8
5
cathode
DC output
inverting
3
input
DIFFERENTIAL
1
STAGE
TDA6101Q
non-inverting
input
black current
measurement
output
CURRENT
SOURCE
MIRROR
MIRROR
4
2
MCD356
ground
(substrate)
supply voltage
input LOW
Fig.1 Block diagram.
1995 Feb 07
3
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
PINNING
SYMBOL
Vip
PIN
DESCRIPTION
1
2
3
4
5
non-inverting voltage input
supply voltage LOW
inverting voltage input
ground, substrate
VDDL
Vin
handbook, halfpage
V
1
2
3
4
5
6
7
8
9
ip
V
DDL
GND
Iom
V
black current measurement
output
in
GND
VDDH
Vcn
6
7
8
9
supply voltage HIGH
I
TDA6101Q
om
cathode transient voltage output
cathode DC voltage output
feedback voltage output
V
DDH
Voc
V
cn
Vfb
V
oc
V
fb
MCD355
Fig.2 Pin configuration.
1995 Feb 07
4
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134). Voltages measured with respect to GND (pin 4);
currents as specified in Fig.1; unless otherwise specified.
SYMBOL
VDDH
PARAMETER
CONDITIONS
MIN.
MAX.
250
UNIT
high level supply voltage
low level supply voltage
input voltage
0
0
0
V
V
V
V
VDDL
VI
14
VDDL
+6
VIdm
Vom
Voc
differential mode input voltage
measurement output voltage
cathode output voltage
feedback output voltage
input current
−6
0
VDDL
VDDH
VDDH
1
VDDL
VDDL
0
V
V
Vfb
Iin,Iip
IocsmL
mA
A
low non-repetitive peak cathode
output current
flashover discharge = 100 µC
0
5
IocsmH
high non-repetitive peak cathode
output current
flashover discharge = 100 nC
0
10
A
Ptot
Tstg
Tj
total power dissipation
storage temperature
junction temperature
electrostatic handling
human body model (HBM)
machine model (MM)
0
1.9
W
−55
−20
+150
+150
°C
°C
Ves
−
−
> 1500
> 400
V
V
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling MOS devices (see “Handling MOS Devices”).
QUALITY SPECIFICATION
Quality specification “SNW-FQ-611 part E” is applicable, except for ESD Human body model see Chapter “Limiting
values”, and can be found in the “Quality reference handbook” (ordering number 9398 510 63011).
THERMAL CHARACTERISTICS
SYMBOL
Rth j-a
PARAMETER(1)
VALUE
UNIT
thermal resistance from junction to ambient in free air
thermal resistance from junction to case
56
12
K/W
K/W
Rth j-c
Note
1. External heatsink not required.
1995 Feb 07
5
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
CHARACTERISTICS
Operating range: Tamb = −20 to 65 °C; VDDH = 180 to 210 V; VDDL = 10.8 to 13.2 V; Vip = 2.6 to 5 V;
Vom = 1.4 V to VDDL
.
Test conditions (unless otherwise specified): Tamb = 25 °C; VDDH = 200 V; VDDL = 12 V; Vip = 5 V; Vom = 6 V; CL = 10 pF
(CL consists of parasitic and cathode capacitance); measured in test circuit Fig.3.
SYMBOL
PARAMETER
CONDITIONS
MIN.
3.5
TYP. MAX. UNIT
IDDH
IDDL
Ibias
quiescent HIGH voltage supply current Voc = 0.5VDDH
quiescent LOW voltage supply current Voc = 0.5VDDH
4.4
2.8
−
5.5
3.5
20
mA
mA
µA
µA
µA
2.2
0
input bias current
input offset current
Voc = 0.5VDDH
Voc = 0.5VDDH
Ioffset
−3
−5
−
0
+3
+5
Iom(offset) offset current of measurement output
Ioc = 0 µA;
−1.0 V < V1−3 < 1.0 V;
1.4 V < Vom < VDDL
linearity of current transfer
−10 µA < Ioc < 3 mA;
−1.0 V < V1−3 < 1.0 V;
1.4 V < Vom < VDDL
0.9
1.0
1.1
∆Iom
∆Ioc
------------
Voffset
Voc(min)
Voc(max)
GB
input offset voltage
Voc = 0.5VDDH
−50
−
VDDH − 12
−
−
−
−
0.8
+50
20
−
mV
V
minimum output voltage
maximum output voltage
V1−3 = −1 V
V1−3 = −1 V
V
gain-bandwidth product of open-loop
gain: Vfb / Vi, dm
f = 500 kHz; VocDC = 100 V
−
GHz
BS
BL
tpd
small signal bandwidth
VocAC = 60 V (p-p);
VocDC = 100 V
7
9
−
MHz
MHz
ns
large signal bandwidth
VocAC = 100 V (p-p);
VocDC = 100 V
5.5
27
7
−
cathode output propagation delay time VocAC = 100 V (p-p);
50% input to 50% output ocDC = 100 V square
38
49
V
wave; f < 1 MHz;
tr = tf = 40 ns;
see Figs 4 and 5
tr
tf
cathode output rise time 10% output to Voc = 50 to 150 V square
43
43
−
55
55
−
68
ns
ns
ns
90% output
wave; f < 1 MHz; tf = 40 ns;
see Fig.4
cathode output fall time 90% output to Voc = 150 to 50 V square
68
10% output
wave; f < 1 MHz; tr = 40 ns;
see Fig.5
ts
settling time 50% input to
(99% < output < 101%)
VocAC = 100 V (p-p);
VocDC = 100 V square
wave; f < 1 MHz;
tr = tf = 40 ns;
350
see Figs 4 and 5
SR
slew rate between 50 V to 150 V
V
1−3 = 2 V (p-p) square
−
1700
−
V/µs
wave; f < 1 MHz;
tr = tf = 40 ns
1995 Feb 07
6
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP. MAX. UNIT
Ov
cathode output voltage overshoot
VocAC = 100 V (p-p);
VocDC = 100 V square
wave; f < 1 MHz;
−
9
−
%
tr = tf = 40 ns;
see Figs 4 and 5; note 1
SVRRH
SVRRL
high supply voltage rejection ratio
low supply voltage rejection ratio
f < 50 kHz; note 2
f < 50 kHz; note 2
−
−
85
70
−
−
dB
dB
Notes
1. If the difference between VDDL and Vip is less than 7 V, overshoot cannot be specified.
2. SVRR: The ratio of the change in supply voltage to the change in input voltage when there is no change in output
voltage.
VDDH to GND must be decoupled:
Cathode output
1. With a capacitor >20 nF with good HF behaviour
(e.g. foil). This capacitance must be placed as close
as possible to pins 6 and 4, but definitely within 5 mm.
The cathode output is protected against peak currents
(caused by positive voltage peaks during high-resistance
flash) of 5 A maximum with a charge content of 100 µC.
2. With a capacitor >10 µF on the picture tube base print
The cathode is also protected against peak currents
(caused by positive voltage peaks during low-resistance
flash) of 10 A maximum with a charge content of 100 nC.
(common for three output stages).
VDDL to GND must be decoupled:
1. With a capacitor >20 nF with good HF behaviour
(e.g. ceramic). This capacitance must be placed as
close as possible to pins 2 and 4, but definitely within
10 mm.
Flashover protection
The TDA6101Q incorporates protection diodes against
CRT flashover discharges that clamp the cathode output
pin to the VDDH pin. The DC supply voltage at the VDDH pin
has to be within the operating range of 180 to 210 V to
ensure that the Absolute Maximum Rating for VDDH of
250 V will not be exceeded during flashover. To limit the
diode current, an external 820 Ω carbon high-voltage
resistor in series with the cathode output and a 2 kV spark
gap are needed (for this resistor-value, the CRT has to be
connected to the main PCB). This addition produces an
increase in the rise and fall times of approximately 5 ns
and a decrease in the overshoot of approximately 3%.
Switch-off behaviour
The switch-off behaviour of the TDA6101Q is defined:
when the bias current becomes zero, at VDDL (pin 2) lower
than approximately 5 V, all the output pins
(pins 7, 8 and 9) will be high.
1995 Feb 07
7
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
12 V
200 V
C
C1
C3
par
22 nF
2.7 pF
C5
22 nF
C6
100 nF
C7 10 µF
7
C4
10 µF
V
i
R10
68.1 kΩ
R9
820 Ω
C2
22 µF
3
1
9
2
6
8
R1
50 Ω
1.4 mA
TDA6101Q
C
n
4
5
560 pF
A
C8
6.8 pF
R3
20 MΩ
5 V
C7
3.2 pF
probe
V
om
6 V
C9
136 pF
R2
1 MΩ
C10
100 nF
MCD357
Cpar = 150 fF.
Fig.3 Test circuit with feedback factor 1⁄83.
1995 Feb 07
8
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
x
V
i
0
x
t
t
s
overshoot (in %)
151
149
150
140
V
oc
100
60
50
t
t
r
MGA974
t
pd
Fig.4 Output voltage (pin 8) rising edge as a function of the AC input signal.
1995 Feb 07
9
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
x
V
i
0
x
t
t
s
150
140
oc
V
100
overshoot (in %)
51
60
50
49
t
t
f
MGA975
t
pd
Fig.5 Output voltage (pins 8) falling edge as a function of the AC input signal.
1995 Feb 07
10
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
The dynamic dissipation equals:
dyn = VDDH × (CL + Cfb + Cint) × fi × Vo(p-p) ×δ
TEST AND APPLICATION INFORMATION
Dissipation
P
CL = load capacitance.
Regarding dissipation, distinction must first be made
between static dissipation (independent of frequency) and
dynamic dissipation (proportional to frequency).
Cfb = feedback capacitance (≈ 150 fF).
Cint = internal load capacitance (≈ 4 pF).
fi = input frequency.
The static dissipation of the TDA6101Q is due to high and
low voltage supply currents and load currents in the
feedback network and CRT.
Vo(p-p) = output voltage (peak-to-peak value).
δ = non-blanking duty-cycle (≈ 0.8).
The static dissipation equals:
The IC must be mounted on the picture tube base print to
minimize the load capacitance (CL).
Pstat = VDDL ×IDDL + VDDH ×IDDH
Vfb
+ Voc ×Ioc – Vfb
×
--------
Rfb
Rfb = value of feedback resistor.
Ioc = DC value of cathode current.
1995 Feb 07
11
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
PACKAGE OUTLINE
DBS9MPF: plastic DIL-bent-SIL medium power package with fin; 9 leads
SOT111-1
D
D
1
A
2
q
P
P
1
Q
A
3
q
2
q
1
A
A
4
E
pin 1 index
c
L
1
9
e
2
b
e
Z
b
w
M
2
θ
b
1
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
(1)
Z
A
max.
2
(1)
(1)
UNIT
A
A
A
b
b
b
c
D
D
E
e
e
L
P
P
Q
q
q
q
2
w
θ
3
4
1
2
1
2
1
1
max.
o
o
18.5
17.8
8.7 15.5 1.40 0.67 1.40 0.48 21.8 21.4 6.48
8.0 15.1 1.14 0.50 1.14 0.38 21.4 20.7 6.20
3.9 2.75 3.4 1.75 15.1
3.4 2.50 3.2 1.55 14.9
65
55
4.4 5.9
4.2 5.7
2.54 2.54
mm
3.7
0.25 1.0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-11-17
95-03-11
SOT111-1
1995 Feb 07
12
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
SOLDERING
REPAIRING SOLDERED JOINTS
Apply the soldering iron below the seating plane (or not
more than 2 mm above it). If its temperature is below
300 °C, it must not be in contact for more than 10 s; if
between 300 and 400 °C, for not more than 5 s.
Plastic single in-line packages
BY DIP OR WAVE
The maximum permissible temperature of the solder is
260 °C; this temperature must not be in contact with the
joint for more than 5 s. The total contact time of successive
solder waves must not exceed 5 s.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified storage maximum. If the printed-circuit board has
been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within
the permissible limit.
DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1995 Feb 07
13
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
NOTES
1995 Feb 07
14
Philips Semiconductors
Preliminary specification
Video output amplifier
TDA6101Q
NOTES
1995 Feb 07
15
Philips Semiconductors – a worldwide company
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Pakistan: Philips Electrical Industries of Pakistan Ltd.,
Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,
KARACHI 75600, Tel. (021)587 4641-49,
Fax. (021)577035/5874546.
Tel. (02)805 4455, Fax. (02)805 4466
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,
Tel. (01)60 101-1236, Fax. (01)60 101-1211
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,
Portugal: PHILIPS PORTUGUESA, S.A.,
Tel. (31)40 783 749, Fax. (31)40 788 399
Rua dr. António Loureiro Borges 5, Arquiparque - Miraflores,
Apartado 300, 2795 LINDA-A-VELHA,
Tel. (01)4163160/4163333, Fax. (01)4163174/4163366.
Brazil: Rua do Rocio 220 - 5th floor, Suite 51,
CEP: 04552-903-SÃO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65)350 2000, Fax. (65)251 6500
South Africa: S.A. PHILIPS Pty Ltd.,
Tel. (011)821-2333, Fax. (011)829-1849
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:
Tel. (800) 234-7381, Fax. (708) 296-8556
Chile: Av. Santa Maria 0760, SANTIAGO,
195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. (011)470-5911, Fax. (011)470-5494.
Tel. (02)773 816, Fax. (02)777 6730
Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17,
77621 BOGOTA, Tel. (571)249 7624/(571)217 4609,
Fax. (571)217 4549
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. (032)88 2636, Fax. (031)57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (9)0-50261, Fax. (9)0-520971
France: 4 Rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01)4099 6161, Fax. (01)4099 6427
Germany: P.O. Box 10 63 23, 20043 HAMBURG,
Tel. (040)3296-0, Fax. (040)3296 213.
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01)4894 339/4894 911, Fax. (01)4814 240
Hong Kong: PHILIPS HONG KONG Ltd., 15/F Philips Ind. Bldg.,
24-28 Kung Yip St., KWAI CHUNG, N.T.,
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03)301 6312, Fax. (03)301 42 43
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,
Tel. (0)8-632 2000, Fax. (0)8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. (01)488 2211, Fax. (01)481 77 30
Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West
Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978,
TAIPEI 100, Tel. (02)388 7666, Fax. (02)382 4382.
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong,
Bangkok 10260, THAILAND,
Tel. (662)398-0141, Fax. (662)398-3319.
Turkey:Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. (0212)279 2770, Fax. (0212)282 6707
United Kingdom: Philips Semiconductors LTD.,
276 Bath Road, Hayes, MIDDLESEX UB3 5BX,
Tel. (0181)730-5000, Fax. (0181)754-8421
United States:811 East Arques Avenue, SUNNYVALE,
CA 94088-3409, Tel. (800)234-7381, Fax. (708)296-8556
Uruguay: Coronel Mora 433, MONTEVIDEO,
Tel. (852)424 5121, Fax. (852)480 6960/480 6009
India: Philips INDIA Ltd, Shivsagar Estate, A Block ,
Dr. Annie Besant Rd. Worli, Bombay 400 018
Tel. (022)4938 541, Fax. (022)4938 722
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,
P.O. Box 4252, JAKARTA 12950,
Tel. (02)70-4044, Fax. (02)92 0601
Tel. (021)5201 122, Fax. (021)5205 189
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. (01)640 000, Fax. (01)640 200
Italy: PHILIPS SEMICONDUCTORS S.r.l.,
Piazza IV Novembre 3, 20124 MILANO,
Tel. (0039)2 6752 2531, Fax. (0039)2 6752 2557
For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BE-p,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. +31-40-724825
Japan: Philips Bldg 13-37, Kohnan2-chome, Minato-ku, TOKYO 108,
Tel. (03)3740 5028, Fax. (03)3740 0580
Korea: (Republic of) Philips House, 260-199 Itaewon-dong,
SCD38
© Philips Electronics N.V. 1994
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
Yongsan-ku, SEOUL, Tel. (02)794-5011, Fax. (02)798-8022
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03)750 5214, Fax. (03)757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905,
Tel. 9-5(800)234-7381, Fax. (708)296-8556
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.
Tel. (040)783749, Fax. (040)788399
Printed in The Netherlands
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09)849-4160, Fax. (09)849-7811
533061/1500/02/pp16
Date of release: 1995 Feb 07
9397 747 50011
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (022)74 8000, Fax. (022)74 8341
Document order number:
Philips Semiconductors
|