Always there to help you
Register your product and get support at
SHQ7300
Question?
Contact
Philips
User manual
Contents
EN
1
1 Important safety
instructions
General information
To avoid damage or malfunction:
Caution
• Do not expose the headset to excessive heat.
• Do not drop your headset.
• Headset shall not be exposed to dripping or splashing.
• Do not allow your headset to be submerged in water.
• Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
Hearing Safety
• If cleaning is required use a soft cloth, if necessary
dampened with a minimum amount of water or diluted
mild soap, to clean the product.
• The integrated battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
Danger
• To avoid hearing damage, limit the time you use the
headset at high volume and set the volume to a safe
level.The louder the volume, the shorter the safe
listening time is.
About operating and storage temperatures
and humidity
•
Operate or store in a place where
temperature is between -15ºC (5ºF) and
55ºC (131ºF) (up to 90% relative humidity.
Battery life may be shorter in high or low
temperature conditions.
Be sure to observe the following guidelines
when using your headset.
•
•
Listen at reasonable volumes for
reasonable periods of time.
•
Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
Compliance with EMF
•
•
Do not turn up the volume so high that
you can’t hear what’s around you.
You should use caution or temporarily
discontinue use in potentially hazardous
situations.
This product complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
•
•
Excessive sound pressure from earphones
and headset can cause hearing loss.
Using the headset with both ears covered
while driving is not recommended and may
be illegal in some areas while driving.
For your safety, avoid distractions from
music or phone calls while in traffic or
other potentially dangerous environments.
•
2
EN
2 Your wireless
in-ear headset
Quick start guide
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
With this Philips wireless in-ear headset, you
can:
Other devices
A mobile phone or device (e.g. notebook, PDA,
Bluetooth adapters, MP3 players etc) which
supports Bluetooth and is compatible to the
headset.
•
•
•
enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music.
Overview of your wireless
headset
What's in the box
Philips Bluetooth wireless headset SHQ7300
Replaceable rubber ear caps
a Micro USB charging slot
b LED light
USB charging cable (for charging only)
c On/off, call/music control button
d Volume/Track control button
e Microphone
Fit loop x 2 sets
f NFC detection area
EN
3
3 Get started
Charge your headset
Note
• Before you use your headset for the first time, charge
the battery for 5 hours for optimum battery capacity
and lifetime.
• Use only the original USB charging cable to avoid any
damage.
• Finish your call before charging the headset, as
connecting the headset for charging will power the
headset off.
• You can operate the headset normally during charging.
Connect the supplied USB charging cable to:
•
the micro USB charging slot on the
headset and;
•
the charger/USB port of a computer.
» LED turns white during charging and
turns off when the headset is fully
charged.
Tip
• Normally, a full charge takes 2.5 hours.
4
EN
area (see 'Overview of your wireless
4 Pair the headset
with your
3 Follow the pairing instructions of your
phone. Enter the password "0000" (4
zeros) if prompted.
mobile phone
Note
Before you use the headset with your mobile
phone for the first time, pair it with a mobile
phone.A successful pairing establishes a unique
encrypted link between the headset and mobile
phone.The headset stores the last 4 devices
in the memory. If you try to pair more than 4
devices, the earliest paired device is replaced by
the new one.
• Make sure your mobile phone has the NFC feature
available and switched on.
• Make sure your mobile phone is not in standby mode.
• Pairing with NFC is only suitable for Android mobile
operating system 4.2 or above.
• Refer to the user manual of your mobile phone to
identify its NFC detection area.
There are two ways to pair your headset with
your mobile phone:
The following example shows you how to pair
the headset with your mobile phone.
•
•
Manual pairing
NFC pairing
1 Activate the Bluetooth feature of your
mobile phone, select Philips SHQ7300.
2 Enter the headset password "0000" (4
zeros) if prompted. For those mobile
phones featuring Bluetooth 2.1+EDR or
higher, no need to enter a password.
Manual pairing
10:35
10:36
10:37
1 Make sure that the headset is fully charged
Settings
Connectivity
Settings
Settings
Connectivity
and turned off.
Bluetooth
Devices Found
Enter Password
****
Philips SHQ7300
Add
Bluetooth
device
2 Press and hold the on/off button until the
blue and white LED flashes alternately.
» The headset remains in pairing mode
for 5 minutes.
0000
Select
Back
Select
Back
Select
Back
3 Make sure that the mobile phone is turned
on and its Bluetooth feature is activated.
4 Pair the headset with the mobile phone.
For detailed information, refer to the user
manual of your mobile phone.
NFC pairing
1 Make sure you turn on the NFC function
on your phone and your phone’s screen
remains active.
EN
5
Turn the headset
off.
Press and
hold for 4
seconds.
Power off
tone
5 Use your
headset
Play or pause
music.
Press once.
N/A
Pick up/hang up
a call.
Reject an
incoming call.
Redial the last
number.
Press once.
1 short
beep
1 short
beep
Connect the headset to a
Bluetooth device
Press and
hold
Press twice. 2 short
beeps
1 Turn on your mobile phone/Bluetooth
device.
Switch caller
during a call.
Press twice
1 short
beep
2 Press and hold the on/off button to turn
the headset on.
» The blue LED flashes.
Volume/Track control button
» The headset is reconnected to
the last connected mobile phone/
Bluetooth device automatically. If the
last one is not available, the headset
tries to reconnect to the second last
connected device.
Adjust volume.
Skip forward.
Skip backward.
Press once
Press and hold
Press and hold
N/A
N/A
N/A
Other headset indicator status
Headset status
Indicator
The blue LED
flashes for every
Tip
The headset is connected
to a Bluetooth device,
while the headset in
standby mode or while you
are listening to music.
The headset is ready for
pairing.
• If you turn on the mobile phone/Bluetooth device or
activate the Bluetooth feature after turning on the
headset, you have to reconnect the headset and mobile
phone/Bluetooth device manually.
6 seconds.
The LED flashes
blue and white
alternately.
The blue LED
flashes quickly.
Note
• If the headset fails to connect to any Bluetooth device
within range in 5 minutes, it will switch off automatically
to save the battery life.
The headset is on but not
connected to a Bluetooth
device.
There is an incoming call.
The blue LED
flashes once per
second.
Manage your calls and music
The battery level is low.
The white LED
flashes.
On/off, call/music control button
The battery is fully charged. The white LED
is off.
Task
Operation
Sound
or LED
indicator
Power on
tone
Turn the headset
on.
Press and
hold for 2
seconds.
6
EN
6 Technical data
•
Up to 5.5 hours of music time or 6 hours
of talk time
•
•
•
Up to 150 hours of standby time
Normal time for a full charge: 2.5 hours
Rechargeable Lithium-ion battery (85
mAh)
•
Bluetooth 3.0, Bluetooth mono support
(Headset Profile - HSP, Hands-Free
Profile - HFP), Bluetooth stereo supported
(Advanced Audio Distribution Profile
- A2DP;AudioVideo Remote Control
Profile - AVRCP)
•
Operating range: Up to 10 meters (33
feet)
•
•
Digital echo & noise reduction
Auto power off
Note
• Specifications are subject to change without notice.
EN
7
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
7 Notice
Declaration of conformity
Hereby,WOOX Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC.You can find the
com.
Remove the integrated battery
Note
• Make sure the headset is disconnected from the USB
charging cable before removing the battery.
This product has been designed, tested and
manufactured according the European R&TTE
directive 1999/5/EC.
If there is no collection/recycling system for
electronic products in your country, you can
protect the environment by removing and
recycling the battery before disposing the
headset.
Disposal of your old product
and battery
1
2
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This symbol means that the product contains
a built-in rechargeable battery covered by
European Directive 2013/56/EU which cannot
be disposed of with normal household waste.
We strongly advise you to take your product to
an official collection point or a Philips service
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
8
EN
Bluetooth device, or remove obstacles between
them.
8 Frequently
asked questions
The audio quality is poor when streaming
from the mobile phone is very slow, or audio
streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but also supports
My Bluetooth headset does not switch on.
The battery level is low. Charge the headset.
I cannot pair my Bluetooth headset with a
mobile phone.
The Bluetooth is disabled. Enable the Bluetooth
feature on your mobile phone and turn on the
mobile phone before you turn on the headset.
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip forward/
backward).
Make sure the Bluetooth audio source supports
Pairing does not work.
Make sure the headset is in pairing mode.
Are the Bluetooth headsets sweat/water
proof?
•
Follow the steps described in this user
manual (see 'Pair the headset with your
The Bluetooth headsets are sweat proof to a
degree of IPX2, and are not designed as water-
proof at audio output areas. Do not wash the
headsets by running water, immerse in water or
use them under water.
•
Make sure that the LED light flashes blue
and white alternately before you release
the on/off button. Do not stop holding the
button if you see the blue LED only.
The mobile phone cannot find the headset.
•
The headset may be connected to a
previously paired device.Turn off the
connected device or move it out of range.
Pairing may have been reset or the headset
has been previously paired with another
device. Pair the headset with the mobile
phone again as described in the user
manual (see 'Pair the headset with your
•
support.
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone, but
music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone.
Select to listen to music through the headset.
The audio quality is poor and crackling noise
can be heard.
The Bluetooth device is out of range. Reduce
the distance between your headset and
10 EN
EN 11
2015 ©WOOX Innovations Limited.All rights
reserved.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used byWOOX Innovations Limited
under license from Koninklijke Philips N.V.
0890
UM_SHQ7300_00_EN_V1.0
wk1502
|