In-Ceiling LCR Cinema Speaker
Additionally, you should allow an extra inch in all directions
behind the ceiling surface to allow room for the doglegs that
retain the frame to the ceiling surface to swing into position.
Congratulations on your purchase of the Phoenix Gold
Innovative Home Audio ATCLCR6 In-Ceiling LCR Cinema
Speaker. This product is designed to reproduce the audio
portion of your home entertainment system with accuracy
and detail that will satisfy the most discriminating listener.
Use a stud finder to locate the joists behind the ceiling surface.
You should now check for obstructions like cross bracing above
and below the desired speaker location.
Please read this Installation Manual to ensure the proper
installation and performance of your ATCLCR6 speaker.
After selection of the mounting location, mark the hole to be
cut out. A handy cardboard template is included with your
ATCLCR6 speaker for your convenience. Locate and align the
template, then mark with pencil on the ceiling surface. If you are
unsure whether there are obstructions behind the ceiling surface
where the speakers are to be mounted, cut a small hole in the
center of your marked mounting location. Holding your drywall
saw at a 45 degree angle (Fig. 2) cut a square hole that you
can use to find any obstructions, should they exist.
Preparing for your Installation
Gather the necessary tools for your installation.
You will need the following tools:
1) A Keyhole or Drywall Saw
2) A Phillips Screwdriver
3) Masking Tape
4) A Pencil
6) A Tape Measure
7) A Stud Finder (recommended)
8) Your ATCLCR6 Speaker
The 45 degree wedge shape of the removed surfacing material
will make replacement, if necessary, a much easier task and
yield a better finish when patching the work.
Figure 2
Plan your speaker placement carefully. Make certain that electrical,
plumbing and any other services will not interfere within the
ceiling where you plan to place your speakers. The ATCLCR6
speakers are specifically designed to be mounted in the ceiling,
and are typically used as a stereo pair, a center channel, or as a
Left, Center, Right home theater installation (Fig. 1).
Once it has been determined that there are no obstructions,
cut the hole to mount the speaker using the drywall saw at a
90 degree angle to the ceiling surface. Cover the raw edges of
the wallboard with masking tape (Fig. 3). This will prevent the
back pressure of the speaker from blowing loose gypsum dust
out and on to the painted wall surface after installation. Do not
allow the tape to extend more than 1/2” beyond the edge of the
hole into the room. The frame of the ATCLCR6 will cover and
hide the tape.
In most modern buildings the ceiling joists are positioned on 16”
centers, providing a space between the studs of approximately 14
3/8”. The ATCLCR6 requires a mounting hole 8 1/8” in diameter.
Figure 3
Next, run your speaker wire to your speaker locations. UL-
rated CL3 speaker wire is recommended when running wire
inside your walls (such as Phoenix Gold Innovative Home
SS162W*). In many areas it may be required by code. When
running your speaker wire avoid running the speaker
20’
wire parallel to the 110V power lines to prevent picking up
hum and interference from the power service. If the speaker
wire needs to cross a 110V power line, place it at a right angle
to the 110V line to minimize any hum or interference.
Directional In-Ceiling
If you are uncomfortable with running the speaker wire yourself
in existing construction, it is recommended that you retain a
qualified custom home installation specialist or electrician.
14’
*Available in 3 convenient lengths: 50’ mini-spool
(M1650W), 100’ mini-spool (M16100W), and 250’ bulk spool
(SS162W/250).
Figure 1
easily done by rotating the speaker until the optimum angle is
achieved- typically a direct line of sight with the listener (Fig. 8).
Next, one at a time, turn each of the four screws (Fig. 9) that
operate the doglegs counter clockwise a few turns until you feel
the dogleg is loose from its resting position. Now turn the screw
clockwise until you feel the dogleg contact the ceiling surface.
Tighten all four of the mounting screws in the same manner
until the speaker is properly aligned and held securely to the
wall surface. Caution: Do not over tighten!
Aiming the Tweeter
Using your fingertips, place them carefully at the edges of the
tweeter housing. Apply gentle pressure to swivel the tweeter to
aim the axis toward the listening area. You can use a piece of
music with a solid center imaged vocalist to assist in correctly
aiming the tweeter. When the tweeters are properly aligned for
the listening area you will hear a coherent and stable center
image from your listening position.
Painting the Speaker
Figure 8
A paint shield is included in the ATCLCR6 speaker package.
Place the paint shield inside the frame to protect the speaker.
You can now safely paint the speaker frame to match your
ceiling surface if you desire.
When painting the grill caution should be taken to ensure that
paint does not clog or block the perforated openings in the grill.
This would prevent full operation from the speaker. We suggest
spray paint only for this application.
Removing the ATCLCR6 Speaker
1
Should it ever become necessary to remove the ATCLCR6
speaker from the ceiling, simply remove the grill and turn the
four mounting screws counter-clockwise until the doglegs lock
out of position in their resting seats.
Recommended Speaker Wire Gauges
2
The resistance of the speaker wire in your installation can
cause your speaker to perform at less than an optimum
quality level. Excess resistance, caused by using an undersized
speaker wire, can result in loss of detail and definition in the low
frequency region of your audio program, as well as a loss of
dynamic range.
To prevent this effect in your installation, we have recommended
speaker wire gauges that should not exceed 0.5 Ohms
resistance over the recommended length of wire run.
4
For the ATCLCR6 speaker, we suggest the following
minimum speaker wire gauge be used:
50’ or less – 16 Gauge 2-Cond. CL3 (PG model M1650W)
50’ – 100’ – 16 Gauge 2-Cond. CL3 (PG model M16100W)
3
ATCLCR6 Specifications
Speaker
6.5” Textured Poly Cone w/Butyl Surround
Tweeter
1” Parachute Silk Dome
55 Hz to 18 kHz
8 Ohm
Frequency Response
Impedance
Sensitivity
Recommended Amp Power
Outer Dimension
Mounting Depth
Cut Out Diameter
25 to 150 Watts Continuous
9 3/8” (237mm)
5” (127mm)
8 1/8” (206mm)
Two Year Limited Warranty
Phoenix Gold Innovative Home Audio, warrants this product against defects in materials and workmanship for a limited period of time.
For a period of two (2) years from date of original purchase, we will repair or replace the product, at our option, without charge for parts.
Customer must pay for all labor charges associated with the removal and re-installation of speakers for the limited period and all parts
and labor charges after the limited warranty period expires. The limited warranty period for factory refurbished products expires after
ninety (90) days from date of original purchase. This limited warranty applies only to purchases from authorized Phoenix Gold Retailers
or Distributors. This limited warranty is extended only to the original purchaser and is valid only to consumers in the United States.
Consumers are required to provide a copy of the original sales invoice from an authorized Phoenix Gold Innovative Home Audio Retailer
or Distributor when making a claim against this limited warranty. This limited warranty only covers failures due to defects in materials or
workmanship that occur during normal use. It does not cover failures resulting from accident, fire, flood, misuse, neglect, mis-handling,
mis-application, alteration, faulty installation, modification, service by anyone other than Phoenix Gold, or damage that is attributable to
Acts of God. It does not cover costs of transportation to Phoenix Gold or damage in transit. The customer should return their defective
product, freight prepaid and insured, to Phoenix Gold only after receiving a Return Authorization.
Repair or replacement under terms of this warranty does not extend the term of this warranty. Should a product prove to be defective in
workmanship or material, the consumer’s sole remedies will be repair or replacement as provided under the terms of this warranty. If the
defective product is discontinued Phoenix Gold may replace the product with an equivalent or superior product at its option. Any cost of
re-installation or repair of wall or ceiling surface is the sole responsibility of the customer and that cost shall not be the responsibility of
Phoenix Gold. Under no circumstances shall Phoenix Gold be liable for loss or damage, direct, consequential or incidental, arising out of
the use of or inability to use the product. There are no express warranties other than described above.
Phoenix Gold 9200 North Decatur Street Portland, Oregon 97203
Tel: 503.286.9300 Fax: 503.978.3381 Tech Support: 800.950.1449
8100.0354A
2007©
|