Planet Technology Network Router WRT 416 User Manual

802.11g Wireless Broadband Router  
WRT-416  
Quick Installation Guide  
 
Package Content  
l 1 x WRT-416  
l 1 x Power Adapter  
l 1 x User’s Manual CD  
l 1 x Quick Installation Guide  
l 1 x External Antenna  
l 1 x Ethernet Cable  
If any of the above items are missing or damaged,  
contact your local dealer for support.  
Note  
 
Hardware Installation  
Before you proceed with the installation, it is necessary that you have  
enough information about the WRT-416.  
l Keep the wireless router as central in your work area as possible.  
Signal strength and speed fall off with distance.  
l Higher is often better. For instance, set it up on the top shelf of a  
bookcase rather than the bottom one, if possible.  
Prior to connecting the hardware, make sure to power off your Ethernet  
device and Wireless Router. Then follow the steps below to connect the  
related devices.  
Step 1: Connect your computer to the LAN port of WRT-416 by  
using RJ-45 cable. Attach one end of the Ethernet cable  
with RJ-45 connector to your hub, switch or a computer’s  
Ethernet port, and the other end to one of the LAN ports of  
your router.  
Step 2: Assemble the antenna to WRT-416. Try to place them  
to a position that can best cover your wireless network. The  
antenna’s position will enhance the receiving sensitivity.  
Step 3: Connect the power adapter. Connect the single DC output  
connector of the power adapter to the power jack on the side  
of the AP. Then plug the Power Adapter into an AC outlet.  
Step 4: Power on the following devices in this order: HUB or  
Switch, router, and PCs  
ONLY use the power adapter supplied with the WRT-416.  
Otherwise, the product may be damaged.  
If you want to reset your WRT-416 to default settings,  
press the Reset button 5 second. Then release the  
button and wait for 10 seconds for rebooting.  
 
Initial Configuration  
1.Open your web browser.  
into the address field of the web browser. Please also make sure your  
PC’s IP address is in the same IP range with WRT-416.  
If the router’s LAN port has been changed with new IP  
address, enter the new IP address instead.  
3.A User Name and Password dialog box will appear. Please enter your  
User Name and Password here. The User Name and Password are  
“admin” by default. Click “OK” to access the management page.  
 
4.Once you log in, the Configuration Wizard and Status page will pop  
up at the same time. Configuration Wizard will appear every time  
you enter WRT-416. If you do not want to display wizard by itself  
next time, select “don’t pop up” option and click “save. In the  
future, you can still have wizard appeared by clicking “Wizard” tab  
on upper right panel of WRT-416’s web page.  
Click “Start” to go to next step.  
in order to start the wizard, you will need to have the  
pop-up blocker DISABLED in your web browser.  
Note  
5.On this page, select your Internet connection type and then input the  
configurations needed to connect to your Internet Service Provider  
(ISP). Please obtain all necessary information from your ISP before  
go through this configuration. Click “Next” to proceed.  
 
6.On this page, you can set the Radio Band, Mode, SSID and Channel  
to your WRT-416. The SSID is to identify your wireless network. All  
the devices (AP and wireless client) on the same wireless network  
must be configured to the same SSID. You can leave the Radio Band  
and Channel settings to default. On the Mode Settings, the default  
is AP mode which allow your wireless client to connect each other  
and the wired Ethernet network. Please refer to the user’s manual  
for detial on other available modes.  
Click “Next” to proceed.  
7.You have finished all basic configurations for WRT-416. Please press  
“Exit” to close this window. The WRT-416 will perform reboot if major  
changes are made. After reboot completes, the WRT-416 is ready to  
use.  
 
Further Configuration  
If you want to configure more detail settings of WRT-416, please refer  
to the manual in the bundled CD. If you have any difficulty on resolving  
the problem while installing or using the WRT-416, please feel free to  
contact PLANET for support.  
 

Peavey Music Mixer Unity 1000 User Manual
Philips Car Stereo System MCM169 User Manual
Philips Hair Clippers HQC688 User Manual
Philips Projection Television 43PP9202 User Manual
Philips TV Cables SWA2541W 10 User Manual
Planet Technology Switch KVM 1600 User Manual
Polaroid Camcorder DVF 130 User Manual
Polaroid Digital Camera PDC 3035 User Manual
PVI Industries Water Heater PV 6323 User Manual
PYLE Audio Car Video System PLTK120 User Manual