SoundStation Premier®500D
SoundStation Premier®550D
Installation Instructions
and User's Guide
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, the following safety precautions should always be followed to reduce the
risk of fire, electric shock, and injury to persons.
M
M
Read and understand all instructions.
M
Never push objects of any kind into the
telephone equipment through housing slots
as they may touch hazardous voltage points
or short out parts that could result in a risk
of electric shock. Never spill liquid of any
kind on the telephone. If liquid is spilled,
however, refer servicing to proper service
personnel.
Follow all warnings and instructions marked
on the instrument.
M
M
Installation must be performed in accordance
with all national wiring rules.
The outlet to which this apparatus is connected
must be installed near the equipment,
and must always be readily accessible.
M
To reduce the risk of electric shock, do
not disassemble this telephone equipment.
Opening or removing covers may expose
you to hazardous voltages. Incorrect
reassembly can cause electric shock when
the equipment is subsequently used.
If your telephone equipment does not work
properly, refer to the section describing
how to get service. The support telephone
number can be found on the outside back
cover of this book.
M
This instrument can be hazardous if immersed
in water. To avoid the possibility of
electrical shock, do not use the telephone
equipment while you are in the bathtub
or shower, or when you are wet. If you
accidentally drop the equipment into water,
do not retrieve it until you have first
unplugged all cords. Do not reconnect the
telephone equipment until it has dried
thoroughly.
M
M
Never install telephone wiring during a
lightning storm.
M
Avoid using the telephone equipment during
electrical storms in your immediate area.
There is a remote risk of electric shock
from lightning. Urgent calls should be brief.
Even though protective measures may have
been installed to limit electrical surges
from entering your home or business, absolute
protection from lightning is impossible.
Never install telephone jacks in wet locations
unless the jack is specifically designed for
wet locations.
M
M
Never touch uninsulated telephone wires or
terminals unless the telephone line has been
disconnected from the network interface.
M
If you suspect a natural gas leak, report
it immediately, but use a telephone away
from the area in question. The telephone
equipment's electrical contacts could generate
a tiny spark. While unlikely, it is possible that
this spark could ignite heavy concentrations
of gas.
Always use caution when installing or
modifying telephone lines.
SAVE THESE INSTRUCTIONS
Table of Contents
®
®
Chapter 1
SoundStation Premier 500D
SoundStation Premier 550D ......................................1
Introduction .......................................................................................2
Checklist of Parts ..............................................................................2
System Compatibility ........................................................................3
To Ensure Better Performance ..........................................................3
Installing SoundStation Premier 500D/550D ....................................3
Using SoundStation Premier 500D/550D .........................................6
In Case of Difficulty ........................................................................10
Maintenance ....................................................................................11
Service .............................................................................................11
Chapter 2
Specifications and Warranty Information ...........13
SoundStation Premier 500/550D ....................................................14
Limited Warranty and Limitation of Liability ................................15
FCC Rules .......................................................................................17
Canadian Department of Communications Notice .........................17
EMC Class A ITE ...........................................................................17
CE Mark LVD and EMC Directive .................................................17
Chapter 1
SoundStation Premier® 500D
SoundStation Premier® 550D
with Extended Mic Option
1
Introduction
Thank you for purchasing SoundStation
Premier® 500D/550D. SoundStation
Premier® 500D/550D delivers the
award-winning full-duplex audioconfer-
encing technology from Polycom in a
“plug-n-play” design for direct connection
SoundStation Premier 500D/550D is
designed for you by Polycom—the World’s
number one provider of audioconferencing
products. From small companies to the
Fortune 500, from the smallest conference
rooms to the largest boardrooms, you will
to most NORTEL® Meridian® digital PBX find more Polycom conferencing products
telephone systems.
in more places than all of our competitors
combined.
With SoundStation Premier® 500D/550D,
you can now connect directly to your
Meridian PBX wall jack with no need
for analog terminal adapters, analog
lines, or analog line cards to support
your conferencing system. Simply plug
SoundStation Premier 500D/550D into
your PBX at the wall, and you are up
and running in seconds.
And now we’ve designed SoundStation
Premier® 500D/550D for you, the Meridian
customer, with the same proven technology
and unparalleled audio quality that has
made SoundStation Premier the most
widely used conferencing product line
in the World.
Checklist of Parts
Your SoundStation Premier 500D/550D
audioconferencing system includes the
following items:
Console to Interface
Module Cable
SoundStation Premier®
500D/550D
RJ11 to RJ45
Network/Phone Cables
(Additional Adapters
Supplied In Some Countries)
User's Documents
Power Adapter
(Varies By Country)
500D/550D
Interface Module
Optional Extended
Microphones
(For 550D)
Optional Extended
Microphones Cables
If any of the above parts is missing,
please contact your Polycom
representative or authorized dealer.
(For 550D)
2
System Compatability
SoundStation Premier 500D/550D is
compatible with any digital voice port
on NORTEL® Meridian®, Meridian 1
(option 11 to 81), SL-1, or SL-100 PBX
with the exception of those supporting
Transfer - in the same manner as the
default M2616 Model 20, using key
number position 3 for Conference and key
number position 6 for Transfer. Contact
your PBX Administrator to confirm that
MBS (CENTREX®) phone sets. In addition the Conference and Transfer functions at
to the basic product functions, it supports
two special functions - Conference and
the port are assigned to these key number
positions.
To Ensure Better Performance
M Locate the SoundStation Premier
M Speak at normal conversation levels.
500D/550D console in a quiet
M Direct your voice toward the
environment, with soft furnishings—
such as carpets, curtains, and sound-
absorbing walls and ceilings.
SoundStation Premier 500D/
550D console.
M Do not move the SoundStation Premier
M Place the console at the center
500D/550D console during a call.
of a table or desk.
M Position extended microphones (option)
6 to 8 feet from the SoundStation
Premier 550D console.
M Keep papers and other objects
away from the console.
M Seat all participants the same distance
from the SoundStation Premier
500D/550D console.
M Participants should sit 3 to 6 feet
from a microphone.
Installing SoundStation Premier 500D/550D
Modular
Wall Jack
1. Insert the large end of one of the
network/phone cables into the
500D/550D Interface Module jack
marked with the Network
icon (
). Plug the other end into the
digital voice jack, as shown below.
500D/550D Interface Module
2. You have the option to install a
Meridian series telephone along with
your SoundStation Premier 500D/550D.
Meridian
Telephone
Replace the telephone cable with
the other network/phone cable. Plug
in the large end to the jack on
the 500D/550D Interface Module
500D/550D
indicated by the telephone icon (
and the other into the telephone.
),
Interface Module
3
Any digital phone supported by your
telephone network can be connected
to the phone jack on the 500D/550D
Interface Module.
3. Plug the long SoundStation Premier
cable into the jack on the 500D/550D
Interface Module labeled with the
SoundStation Premier ( )icon as
shown.
500D/550D
Interface Module
SoundStation Premier
500D/550D Console
4. Plug the other end into the slot under
the SoundStation Premier 500D/550D
Console as illustrated.
Then thread the cable through the
channels on the underside of the
console as shown at right.
5. The SoundStation Premier 550D
is designed for greater room
Extended
Microphone
SoundStation Premier
550D Console
coverage with extended microphones.
If using the optional extended
microphones, connect to SoundStation
Premier 550D as shown at right.
6. Plug the Power Adapter Cable into
the 500D/550D Interface Module jack
marked
then plug the Power
Electrical
Outlet
Adapter into the electrical outlet.
The first time the SoundStation Premier
500D/550D is powered up and
connected to the network through the
500D/550D Interface Module, it will
run a brief self-test and synchronize
itself with your telephone network.
During this time the LEDs will blink.
When the process is complete you
will hear a “bong” tone and the
LEDs will switch off. (This process
can take 20 seconds.)
Power
Adapter
500D/550D
Interface Module
4
7. Place the SoundStation Premier
500D/550D on a flat, stable
surface in the center of the room.
If using the extended hypercardiod
microphones with the 550D, for the
best coverage, position as shown in the
examples to the right.
8. Press ON/OFF to hear a dial tone.
green when the system is on.
Press ON/OFF to terminate any
conference call.
The microphone status LEDs on the
top of the console will show a steady
ON/OFF
9. Press ON/OFF again and while
the phone is off adjust the ringer
volume on the SoundStation Premier
500D/550D by pressing SHIFT
There are four settings: OFF, LOW,
MID, and HIGH. The levels will be
heard after each key press and shown
on the display. After 5 seconds the
display will return to its previous mode.
then VOL or VOL
.
RINGER VOL
VOL
10.To program your phone number, press
SHIFT then press the CONF key.
THIS PHONE #
CONF
Enter the phone number with area code,
using the key to enter a space.
*
When finished, press CONF again.
To retrieve the phone number at any
time during a phone call, press SHIFT
then press the CONF key. The phone
number will be displayed for 10
seconds, after which the display will
return to its previous mode. This display
will default to this number while the
conference phone is inactive.
You are now ready to use your
SoundStation Premier 500D/550D.
5
/
Using the SoundStation Premier 500D 550D System
To Place a Phone Call
If the system is not already on,
When you are ready to end a call,
press ON/OFF and dial the number.
The console display will go blank,
then show each number as it is being
dialed. (Remember, depending on your
PBX, you may need a special dialing
prefix to access outside lines.)
press ON/OFF again.
RINGER VOL
VOL
HOLD
C
B
E F
ON/OFF
THIS PHONE
#
HI
K L
N
O
CONF
TRANSFER
REDIAL
MUTE
SHIFT
U
V
Once the call is connected, a timer will
appear on the display showing how long
the call has been in process.
To Answer a Call
Press ON/OFF when you hear
the SoundStation Premier 500D/550D
Console’s tone.
To Adjust Tone Volume and Speaker Volume
When the phone is on and a dial
tone is heard, adjustment of the dial
tone volume can be made by pressing
There are 32 volume levels—stored
independently in the system’s
memory—for both dial tone
and speaker volume.
VOL or VOL
.
The display will show: TONE VOL.
After 5 seconds, the display will revert
to its previous mode.
RINGER VOL
VOL
HOLD
C
B
E F
ON/OFF
THIS PHONE
#
Once a call is connected, the speaker
volume can be made louder by pressing
VOL or softer by pressing
HI
K L
N
O
CONF
TRANSFER
REDIAL
MUTE
SHIFT
U
V
VOL. The display will show SPKR
VOL. After 5 seconds, the display will
revert to its previous mode.
To Place the Call On Hold
To place a phone call on HOLD at any
time, press SHIFT then press MUTE.
This shuts off the speaker and all
microphones. The display will show
HOLD and all LEDs will begin
blinking red.
RINGER VOL
VOL
C
B
E F
ON/OFF
THIS PHONE
#
HOLD
HI
K L
N
O
CONF
TRANSFER
REDIAL
MUTE
SHIFT
U
V
To take the call off HOLD,
press the MUTE key again.
6
To Transfer a Call
To TRANSFER a call, press SHIFT
then press REDIAL. At the dial tone,
dial the extension to which the call is
being transferred. Press REDIAL again to
complete the transfer, either when you
hear ringing or after talking privately with
the person to whom the call is being
transferred. To cancel a transfer attempt
press ON/OFF, instead of the second
REDIAL press, anytime during the attempt.
Note: Since the conference phone is a
single line phone, all conferenced parties
will be transferred when this function is
used
RINGER VOL
B
K
U
E
ON/OFF
THIS PHONE
VOL
HOLD
#
H
N
CONF
TRANSFER
REDIAL
MUTE
SHIFT
While dialing, the extension will show
on the display. The display will revert
to its previous mode after the transfer is
completed or cancelled.
To Mute the Microphone
To shut off the microphones while
keeping the speaker on, press MUTE.
This shuts off all microphones including
extended microphones, if installed.
RINGER VOL
VOL
C
B
E F
ON/OFF
THIS PHONE
CONF
#
HOLD
HI
K L
N
O
MUTE
TRANSFER
REDIAL
U
V
SHIFT
The display will show MUTE and
the LEDs will turn from green to red.
To take the call off MUTE, press
MUTE again.
To Redial the Last Phone Number Called
Press REDIAL. The display on the main
keypad will show the last phone number
which you called or attempted to call.
RINGER VOL
VOL
C
B
E F
ON/OFF
THIS PHONE
CONF
#
HOLD
HI
K L
N
O
MUTE
SHIFT
The ON/OFF key does not have to be
pressed for REDIAL to initiate a call.
TRANSFER
REDIAL
U
V
Using an Optional Lapel Mic or Recording Device
Your 500D/550D Interface Module is
equipped with an RCA jack labeled
AUX I/O to accommodate either your
Polycom Lapel Microphone (available as
an accessory), or to record a conversation.
To record, plug one end of an RCA-type
connector into the jack on a tape recorder
labeled AUX IN and the other end into the
500D/550D Interface Module.
AUX I/O
7
To Establish a Conference
You may use your SoundStation Premier
500D/550D to establish a conference call
of two or more parties. Place your first
call and ask the party to hold while you
conference additional parties. Press the
CONF button. This places the first party
on hold while you dial the next number.
The display will show CONFERENCE,
then the number being dialed. The green
LED’s on the console will blink to indicate
that a conference attempt is in process.
If you successfully reach the second
party and wish to add that party to the
conference call, press CONF again. The
display will show CONFERENCE again
and the second party will be added to
the call. The display will change to call
duration and the LED’s will stop blinking.
If you reach voicemail or do not wish
to add the second party to the call, press
ON/OFF and that party will be dropped.
Repeat these steps to dial then add or drop
additional parties.
Conferencing features, including the
number of parties that can be conferenced
on a single call, vary by PBX system.
Check with your network administrator
if you are unsure about the conferencing
services provided.
CAUTION: Once added to the conference,
calls cannot be selectivey dropped without
terminating the conference call.
Take care to terminate unwanted
calls - busy tone, voicemail, a person
otherwise occupied - by pressing
ON/OFF before pressing CONF
to begin the next attempt. Far end
participants may hang up at any time.
Using the Meridian Phone
While the SoundStation Premier
500D/550D is not in use you may use
the Meridian phone (connected to the
500D/550D Interface Module) and it will
function as usual.
Calls Answered On the Meridian Phone
Incoming calls will ring on both the
Meridian phone and the SoundStation
blink red to indicate the mute condition
until the handset is returned to the cradle,
Premier 500D/550D. If you answer the call then return to the green steady state.
on the Meridian phone and want to speak
on the conference phone, simply press
ON/OFF on the conference phone and
hang up the handset. The LED's will
The call will be active on the conference
phone and all functions will be as defined
for calls initiated on the conference phone.
Conferences Established On the Meridian Phone
Conference calls already established
the handset. The LED's will blink red
on the Meridian phone can be easily moved to indicate the mute condition until
to the SoundStation Premier 500D/550D
by pressing the ON/OFF button on
the conference phone then replacing
the handset is returned to the cradle,
then return to the green steady state.
The 500D/550D will function as if the
8
conference call had originated on the
is established, and included or dropped,
conference phone. If the PBX limit has not will result in dropping all callers if you
been reached, new parties may be added
or dropped as described earlier. Caution:
attempting to move conferences before
the cycle is complete, i.e. before the call
subsequently push the ON/OFF button
on the conference phone.
Mute Initiated By the Meridian Phone
If you have a Meridian phone connected
to the Interface Module, and your
When you lift the handset, all microphones
and the speaker on the console are muted.
The red LED’s will blink to indicate
the mute condition. When the handset
is returned to the cradle, the conference
call is resumed and the LED’s return
to a steady state.
SoundStation Premier 500D/550D
is in use, you may use your phone to
break away from the public conference
call to speak privately to the far end(s)
without disconnecting the conference call.
Using Extended Microphones With 550D
Your SoundStation Premier 550D may be
adaptable to a larger conference room with
the addition of Extended Microphones.
If not purchased with your SoundStation
Premier 550D, these are available as an
accessory from your Polycom Distributor.
MUTE
Red LED
To mute all microphones from the
extended microphone, press MUTE.
To resume two-way communications,
press MUTE again. The red LED will
return to green.
An ON/OFF switch is located on each
of the extended microphones.
By switching to the O position, the LED
MUTE light will turn red and only this
microphone will be shut off. Switching
to the 1 position will turn the
microphone back on.
9
In Case of Difficulty
No Dial Tone
M Check that all connections are
M Disconnect and reconnect all
cables in order as described in
the installation instructions.
correct and tight.
M Confirm that you are connected to
a Meridian digital voice jack.
The SoundStation Premier 500D/550D Console Does Not Ring
M Ringer volume is set at OFF.
Reset according to instructions.
Short Silences, Echoes, or Clipped Speech
M Do not move the SoundStation Premier
M The other party may be using
lower-quality equipment or a
500D/550D console while it is in use.
half-duplex conference bridge,
in which case there may be little
you can do to improve performance.
M Keep your hands away from
the console during calls.
M Keep papers, cups, coffee pots, etc.,
M Try calling again to see if another
away from the console.
line provides a better connection.
M At the beginning of a call, let someone
at each location speak in turn for a few
moments, to enable the system to adapt
to its environment.
Muffled or “In a Well” Reception
M Speak closer to the console so the
M Add more sound absorbency to the
microphones can pick up your speech.
room.
Excessive Noise
M Close conference room doors.
M Try calling again to see if another line
provides a better connection.
M Noisy equipment, such as a computer or
fan, may make it difficult for you to hear
the other party. Both parties should turn
off any noisy equipment.
Physical Damage
M If physical damage is severe enough
that the internal parts become visible,
disconnect the SoundStation Premier
500D/550D immediately. Do not
reconnect it to the network until the
equipment has been repaired.
10
Maintenance
Unplug all cords from the modular wall
jack before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Service
Unplug the telephone from the modular
wall jack and refer servicing to qualified
service personnel when any of these
conditions exist:
M If liquid has been spilled into the
M If the telephone equipment has been
dropped or the housing has been
damaged.
telephone equipment.
M If the telephone equipment has been
exposed to rain or water.
M If you note a distinct change in the
performance of the equipment.
M If the equipment does not operate
according to operating instructions.
Adjust only those controls described
in the operating instructions.
If you need more help, please contact
your Polycom representative or authorized
dealer.
Do not attempt to adjust any other
controls since doing so may result
in damage to the equipment and will
require extensive work by a qualified
technician to restore the telephone
equipment to normal operation.
11
Chapter 2
Specifications and
Warranty Information
13
Specifications
Audio Bandwidth
Extended Microphones
200 to 3500 Hz
Size:
4.125 in 3 in 1in
Weight: 0.25 lb (0.10 Kg)
Cabling: Two-wire RJ9, 8ft
Loudspeaker Volume
89 dBSPL
Environmental Requirements
Network Interface
NORTEL® Meridian®, Meridian 1
(option 11 to 81), SL-1, or SL-100 digital PBX
Temperature:5 °- 40° C operating
Humidity:
20% - 85% non-condensing
Recommended Room Conditions
SystemPower Requirements
Reverberation time: < 0.4 seconds
90-110 VAC, 60 Hz.
Noise level:
< 48 dBA
Console
Registration
Power: 20 VDC, 800 mA
UL, FCC, Industry Canada, CE
Size: 13.8 in 13 in 2.5 in
(35cm 33cm 6.4cm)
Weight:2.0 lbs (0.9 Kg)
Interface Module
Power: 20 VDC, 150 mA
Size: 3.125 in 7.75 in 1.875 in
(7.9cm 19.7cm 4.8cm)
Weight:0.75 lbs (0.34Kg)
Cable length to console:
25 ft (7.6m) to console
Cable length to telephone wall jack:
6 ft (1.8m)
RCA jack:
Line level to tape recorder
or Remote Lapel
Microphone
14
Limited Warranty and Limitation of Liability
Limited Warranty
Polycom warrants to the end user
warrants any replaced or repaired product
or part for ninety (90) days from shipment,
or the remainder of the initial warranty
period, whichever is longer.
(“Customer”) that this product will be
free from defects in workmanship and
materials, under normal use and service,
for three years from the date of purchase
from Polycom or its authorized reseller.
Products returned to Polycom must be
sent prepaid and packaged appropriately
for safe shipment, and it is recommended
that they be insured or sent by a method
that provides for tracking of the package.
Responsibility for loss or damage does not
transfer to Polycom until the returned item
is received by Polycom. The repaired or
replaced item will be shipped to Customer,
Polycom’s sole obligation under this
express warranty shall be, at Polycom’s
option and expense, to repair the defective
product or part, deliver to Customer an
equivalent product or part to replace the
defective item, or if neither of the two
foregoing options is reasonably available,
Polycom may, in its sole discretion, refund at Polycom’s expense, not later than thirty
to Customer the purchase price paid for
the defective product. All products that
are replaced will become the property of
Polycom. Replacement products or parts
may be new or reconditioned. Polycom
(30) days after Polycom receives the
defective product, and Polycom will retain
risk of loss or damage until the item is
delivered to Customer.
Exclusions
WARRANTY EXCLUSIVE. IF A POLYCOM
PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER’S
SOLE REMEDY FOR BREACH OF THAT
WARRANTY SHALL BE REPAIR,
REPLACEMENT, OR REFUND OF THE
PURCHASE PRICE PAID, AT POLYCOM’S
OPTION. TO THE FULL EXTENT
Polycom will not be liable under this
limited warranty if its testing
and examination disclose that the alleged
defect or malfunction in the product does
not exist or results from:
M Failure to follow Polycom’s installation,
ALLOWED BY LAW, THE FOREGOING
WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND ARE IN LIEU OF ALL
OTHER WARRANTIES, TERMS, OR
CONDITIONS, EXPRESS OR IMPLIED,
EITHER IN FACT OR BY OPERATION
OF LAW, STATUTORY OR OTHERWISE,
INCLUDING WARRANTIES, TERMS, OR
CONDITIONS OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE,
SATISFACTORY QUALITY,
CORRESPONDENCE WITH DESCRIPTION,
AND NON-INFRINGEMENT, ALL OF
WHICH ARE EXPRESSLY DISCLAIMED.
POLYCOM NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR IT ANY OTHER LIABILITY
IN CONNECTION WITH THE SALE,
INSTALLATION, MAINTENANCE OR USE
OF ITS PRODUCTS.
operation, or maintenance instructions.
M Unauthorized product modification
or alteration.
M Unauthorized use of common carrier
communication services accessed
through the product.
M Abuse, misuse, negligent acts or
omissions of Customer and persons
under Customer’s control; or
M Acts of third parties, acts of God,
accident, fire, lighting, power surges
or outages, or other hazards.
15
Service Agreements
FOR INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS
OF REVENUE OR PROFITS, LOSS OF
BUSINESS, LOSS OF INFORMATION OR
DATA, OR OTHER FINANCIAL LOSS
ARISING OUT OF OR IN CONNECTION
WITH THE SALE, INSTALLATION,
MAINTENANCE, USE, PERFORMANCE,
FAILURE, OR INTERRUPTION OF ITS
PRODUCTS, EVEN IF POLYCOM OR ITS
AUTHORIZED RESELLER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY
TO REPAIR, REPLACEMENT, OR REFUND
OF THE PURCHASE PRICE PAID, AT
POLYCOM’S OPTION. THIS DISCLAIMER
OF LIABILITY FOR DAMAGES WILL
NOT BE AFFECTED IF ANY REMEDY
PROVIDED HEREIN SHALL FAIL OF ITS
ESSENTIAL PURPOSE.
For information on Polycom service
agreements, call Polycom’s Technical
Assistance Center (TAC) Monday through
Friday 6:00 AM to 6:00 PM Pacific
Time, excluding U.S. holidays, at
telephone number 1-800-POLYCOM
(1-800-765-9266). The e-mail address
If you purchased your product from a
Polycom Authorized Reseller, contact the
Authorized Reseller for information about
service agreements applicable to your
product.
LIMITATION OF LIABILITY. TO THE
FULL EXTENT ALLOWED BY LAW,
POLYCOM EXCLUDES FOR ITSELF
AND ITS SUPPLIERS ANY LIABILITY,
WHETHER BASED IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE),
Disclaimer
Some countries, states, or provinces do not limited in their application to you. When
allow the exclusion or limitation of implied the implied warranties are not allowed
warranties or the limitation of incidental or to be excluded in their entirety, they
consequential damages for certain products will be limited to the duration of the
supplied to consumers, or the limitation
of liability for personal injury, so the
above limitations and exclusions may be
applicable written warranty. This warranty
gives you specific legal rights which may
vary depending on local law.
Governing Laws
This Limited Warranty and Limitation of
Liability shall be governed by the laws of
the State of California, U.S.A., and by the
laws of the United States, excluding
their conflicts of laws principles. The
United Nations Convention on Contracts
for the International Sale of Goods is
hereby excluded in its entirety from
application to this Limited Warranty
and Limitation of Liability.
16
FCC Rules
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
is operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference
in which case the user will be required to
correct the interference at his own expense.
(1) This device may not cause harmful
interference, and
(2) This device must accept any
interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference when the equipment
In accordance with part 15 of the FCC
rules, the user is cautioned that any
changes or modifications not expressly
approved by Polycom Inc. could void the
user’s authority to operate the equipment.
Canadian Department of Communications Notice
This Class [A] digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe [A]
est conforme à la norme N M B-003 du
Canada.
EMC Class A ITE
WARNING
This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
CE Mark LVD and EMC Directive
This SoundStation Premier® 500/550D has of the Declaration of Conformity can be
been marked with the CE mark. This mark
indicates compliance with EEC Directives
89/336/EEC and 73/23/EEC. A full copy
obtained from Polycom Ltd, Whichford
House, Parkway Court, Oxford Business
Park South, Oxford, OX4 2JY, UK
17
Don’t forget to mail in your Owner Registration Card!
Polycom, Inc., 1565 Barber Lane, Milpitas, CA 95035 USA
© 2002 Polycom, Inc. All rights reserved. No part of the contents of this manual may be copied, reproduced, or transmitted
in any form or by any means, or translated into another language or format, in whole or part, without written consent from
Polycom, Inc. Do not remove (or allow anybody else to remove) any product identification, copyright or other notices.
Polycom®, the Polycom logo design, and SoundStation Premier® are registered trademarks,
of Polycom, Inc. in the U.S. and various other countries.
Other company and brand names may be trademarks of the respective
companies with which they are associated.
1725-07090-002 REV D
|