R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
1420
1630
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Poulan
7349 Statesville Road
Charlotte, NC 28269
Poulan
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
115259626 Rev. 2 4/15/10 BRW
S Keep the handles dry and clean and
free from oil and grease.
the plug does not fit fully into the exten-
sion cord, reverse the plug. If the plug
still does not fit, obtain a correct polar-
ized extension cord. A polarized exten-
sion cord will require the use of a polar-
ized wall outlet. This plug will fit into the
polarized wall outlet only one way. If
plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not
fit, contact a qualified electrician to install
the proper wall outlet. Do not change the
equipment plug, extension cord recep-
tacle, or extension cord plug in any way.
S To reduce risk of electrical shock, use
extension cords specifically marked as
suitable for outdoor appliances. The
electrical rating of the cord must not be
less than the rating of the unit. The cord
must be marked with suffix “W--A” (in
Canada, “W”). Use a polarized cord.
Make sure your extension cord is in
good condition. Inspect extension cord
before use and replace if damaged. Do
not use a damaged cord. Cord insula-
tion must be intact with no cracks or de-
terioration. Plug connectors must be
undamaged. An undersized extension
cord will cause a drop in line voltage re-
sulting in loss of power and overheating.
If in doubt, use the next heavier gauge.
The lower the gauge number, the heavi-
er the cord (see SELECT AN EXTENSION
CORD in the OPERATION section). Do
not use multiple cords.
S Keep oil cap and fasteners securely
tightened.
S Nonconforming replacement compo-
nents or the removal of safety devices
may cause damage to the unit and pos-
sible injury to the operator or bystand-
ers. Use only Poulan accessories and
replacement parts as recommended.
Never modify your saw.
S Maintain chain saw with care.
S Keep unit sharp and clean for better
and safer performance.
S Follow instructions for lubricating and
changing accessories.
S Unplug the chain saw from the power
source when not in use, before servic-
ing, and when changing accessories
and attachments, such as saw chain
and guard.
S Check for damaged parts. Before fur-
ther use of the chain saw, a guard or
other part that is damaged should be
carefully checked to determine that it will
operate properly and perform its in-
tended function. Check for alignment of
moving parts, binding of moving parts,
breakage of parts, mounting and any
other conditions that may affect its op-
eration. A guard or other part that is
damaged should be properly repaired
or replaced by an authorized service
dealerunless otherwise indicated else-
where in the instruction manual.
S Do not abuse cord. Never carry the
unit by the extension cord or yank ex-
tension cord to disconnect unit.
S When not in use, chain saws should
be stored in a dry, high or locked-up
place out of the reach of children.
S When storing saw, unplug and use a
bar sheath or carrying case.
S Secure extension cord to power cord
to prevent disconnection from unit.
S Do not use the unit if the switch does
not turn the unit on and off properly, or
if the lock--out does not work. Repairs
to the switch must be made by an
authorized service dealer.
S Keep extension cord clear of operator
and obstacles at all times. Position
cord so that it will not be caught on
branches. Do not expose cords to
heat, oil, water, or sharp edges.
S To avoid the possibility of electric shock,
avoid body contact with any grounded
conductor, such as metal fences or
pipes.
S Ground Fault Circuit Interrupter
(GFCI) protection should be provided
on circuit or outlet to be used. Recep-
tacles are available having built-in
GFCI protection and may be used for
this measure of safety. Inspect chain
saw cords periodically and if dam-
aged, have repaired by an authorized
service dealer.
ELECTRICAL SAFETY
WARNING: Avoid a dangerous en-
vironment. To reduce the risk of electrical
shock, do not use in rain, in damp or wet
locations, or around swimming pools, hot
tubs, etc. Do not expose to snow, rain, or
water to avoid the possibility of electrical
shock. Do not handle extension cord or
plug with wet hands.
S Use a voltage supply as shown on the
nameplate of the unit.
S Avoid dangerous situations. Do not use
in the presence of flammable liquids or
gases to avoid creating a fire or explo-
sion and/or causing damage to unit.
S To reduce the risk of electrical shock,
this appliance has a polarized plug (one
blade is wider than the other) and will re-
quire the use of a polarized extension
cord. The appliance plug will fit into a po-
larized extension cord only one way. If
3
GUARD AGAINST KICKBACK
Follow all safety rules to help avoid kick-
back and other forces which can result in
serious injury.
S Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
S Never let the moving chain contact
any object at the tip of the guide bar.
S Keep working area free from obstruc-
tions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate
or avoid any obstruction that your saw
chain could hit while cutting.
S When cutting a branch, do not let the
guide bar contact another branch or
other objects around it.
Kickback Path
Avoid Obstructions
S Keep saw chain sharp and properly
tensioned. A loose or dull chain can in-
crease the chance of kickback. Follow
manufacturer’s chain sharpening and
maintenance instructions. Check ten-
sion at regular intervals, but never with
engine running. Make sure bar mount-
ing nuts are securely tightened.
S Begin and continue cutting at full
speed. If the chain is moving at a slow-
er speed, there is greater chance of
kickback occurring.
Clear The Working Area
WARNING: Avoid kickback which
can result in serious injury. Kickback is
the backward, upward or sudden for-
ward motion of the guide bar occurring
when the saw chain near the upper tip of
the guide bar contacts any object such
as a log or branch, or when the wood
closes in and pinches the saw chain in
the cut. Contacting a foreign object in
the wood can also result in loss of chain
saw control.
S Rotational Kickback can occur when
the moving chain contacts an object at
the upper tip of the guide bar. Thiscon-
tact can cause the chain to dig into the
object, which stops the chain for an
instant. The result is a lightning fast,
reverse reaction which kicks the guide
bar up and back toward the operator.
S Pinch-Kickback can occur when the
the wood closes in and pinches the
moving saw chain in the cut along the
top of the guide bar and the saw chain
is suddenly stopped. This sudden
stopping of the chain results in a rever-
sal of the chain force used to cut wood
and causes the saw to move in the op-
posite direction of the chain rotation.
The saw is driven straight back toward
the operator.
S Use extreme caution when re-enter-
ing a cut.
S Do not attempt cuts starting with the tip
of the bar (plunge cuts).
S Watch for shifting logs or other objects
that could close a cut and pinch or fall
onto chain.
S Use the specified Reduced-Kickback
Guide Bar and Low Kickback Chain.
Avoid Pinch--Kickback:
S Be extremely aware of situations or ob-
structions that can cause material to
pinch the top of or otherwise stop the
chain.
S Do not cut more than one log at a time.
S Do not twist the saw as the bar is with-
drawn from an undercut when bucking.
Avoid Pull-In:
S Always begin cutting with the saw at
full speed and the saw housing
against wood.
S Use wedges made of plastic or wood.
Never use metal to hold the cut open.
S Pull-In can occur when the moving
chain contacts a foreign object in the
wood in the cut along the bottom of the
guide bar and the saw chain is sud-
denly stopped. This sudden stopping
pulls the saw forward and away from
the operator and could easily cause
the operator to lose control of the saw.
REDUCE THE CHANCE OF
MAINTAIN CONTROL
Never Reverse
Hand Positions
Keep a firm grip
with both hands,
left thumb under
handle
KICKBACK
The following precautions should be fol-
lowed to minimize kickback:
Correct Position
Correct Grip Incorrect Grip
4
S A good, firm grip on the saw with both
hands will help you maintain control.
Don’t let go. Grip the rear handle with
your right hand whether you are right or
left handed. Wrap the fingers of your left
hand over and around the front handle-
bar, and your left thumb under the front
handlebar. Keep your left arm straight
with the elbow locked.
Small Radius
Tip Guide Bar
Large Radius
Tip Guide Bar
S Low Kickback Chain has metkickback
performance requirements when
tested on the representative sample of
these chain saws specified in ANSI
B175.1.
S Position your left hand on the front
handlebar so it is in a straight line with
your right hand on the rear handle
when making bucking cuts. Stand
slightly to the left side of the saw to
keep your body from being in a direct
line with the cutting chain.
Low Kickback Chain
Contoured Depth Gauge
Elongated Guard Link
Deflects Kickback Force
And Allows Wood To
S Stand with your weight evenly bal-
anced on both feet.
S Do not overreach. You could be drawn
or thrown off balance and lose control.
S Do not cut above shoulder height. It is
difficult to maintain control of saw
above shoulder height.
Gradually Ride Into Cutter
WARNING: Computed Kickback
Angle (CKA) listed on your saw and listed
in the following CKA Table represents the
angle of kickback your bar and chain
combinations will have when tested in ac-
cordance with CSA and ANSI standards.
Computed angles represented in the CKA
column indicate total energy and angle
associated without a chain brake. When
purchasing replacements, considerations
should be given to the lower CKA values.
In all cases, lower CKA values representa
safer operating environment for the user.
S Tip contact in some cases may cause
a lightning fast REACTION, kicking the
guide bar up and back toward the op-
erator.
S Pinching the saw chain along the tip of
the guide bar may push the guide bar
rapidly back towards the operator.
S Either of these reactions may cause
you to lose control of the saw which
could result in serious injury. Do not
rely exclusively upon safety devices
built into your saw.
KICKBACK SAFETY FEATURES
WARNING: The following features
are included on your saw to help reduce
hazard of kickback; however, such fea-
tures will not totally eliminate this dan-
ger. Do not rely only on safety devices.
S Hand Guard: designed to reduce the
chance of your left hand contacting
the chain if your hand slips off the front
handlebar.
S Position of front and rear handlebars:
designed with distance between han-
dles and “in-line” with each other. The
spread and “in-line” position of the
hands provided by this design work to-
gether to give balance and resistance
in controlling the pivot of the saw back
toward the operator if kickback oc-
curs.
S Reduced-Kickback Guide Bar: de-
signed with a small radius tip which re-
duces the size of the kickback danger
zone on the bar tip. This type bar has
been demonstrated to significantly re-
duce the number and seriousness of
kickbacks when tested in accordance
with ANSI B175.1.
The following guide bar and chain com-
binations meet kickback requirements of
CSA Z62.1 & Z62.3 and ANSI B175.1
when used on saws listed in this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.
Computed kickback angle (CKA) Table
BAR
MODEL
CHAIN P/N
952051209
952051211
CKA
37_
37_
P/N
Length
14″
1420
1630
952044368
952044370
16″
5
SAFETY NOTICE: Exposure to vibra-
tions through prolonged use of hand
tools could cause blood vessel or nerve
damage in the fingers, hands, and joints
of people prone to circulation disorders
or abnormal swelling. Prolonged use in
cold weather has been linked to blood
vessel damage in otherwise healthy
people. If symptoms occur such as
numbness, pain, loss of strength,
change in skin color or texture, or loss of
feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration sys-
tem does not guarantee the avoidance
of these problems. Users who operate
power tools on a continual and regular
basis must closely monitor theirphysical
condition and the condition of this tool.
DOUBLE INSULATION
double insulation system only provides
added protection against injury resulting
from an internal electrical insulation fail-
ure.
WARNING: All electrical repairs to
this unit, including housing, switch, mo-
tor, etc., must be diagnosed and re-
paired by qualified service personnel.
Replacement parts for a double insu-
lated appliance must be identical to the
parts they replace. A double insulated
appliance is marked with the words
“double insulation” or “double insu-
lated”. The symbol
(square within a
square) may also be marked on the ap-
pliance. Failure to have the unit repaired
by authorized service personnel can
cause the double insulation construc-
tion to become ineffective and result in
serious injury.
CONSTRUCTION
STANDARDS: This product is listed by
Underwriters Laboratories, Inc. inaccor-
dance with UL Standard 1662 and CSA
Standards Z62.1 and Z62.3 and ANSI
B175.1.
This unit is double insulated to help pro-
tect against electric shock. Double insula-
tion construction consists of two separate
“layers” of electrical insulation instead of
grounding.
Tools built with this insulation system are
not intended to be grounded. No ground-
ing means is provided on this unit, nor
should a means of grounding be added to
this unit. As a result, the extension cord
used with this unit can be plugged into any
polarized 120 volt electrical outlet.
ANSI B175.1--2000 “American National
Standard for Powered Tools -- Safety Re-
quirements”
CSA Z62.3 “Chain Saw Kickback Occu-
pational Health and Safety”
CSA Z62.1 “Chain Saws -- Occupational
Health and Safety”
Safety precautions must be observed
when operating any electrical tool. The
SAVE THESE INSTRUCTIONS
ASSEMBLY
NOTE: If you need assistance or find
parts missing or damaged, please call
1-800-554-6723.
WARNING: Before using chain
saw, ensure all fasteners are secure.
CARTON CONTENTS
S Chain Saw (fully assembled)
S Bar Sheath
ASSEMBLY
Your saw is fully assembled; no as-
sembly is necessary.
Examine parts for damage. Do not use
damaged parts.
6
OPERATION
KNOW YOUR SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the
location of the various controls and adjustments. Save this manual for future refer-
ence.
Oiler Actuator/
Bar Oil Cap
Chain Adjustment
Screw
Bar Sprocket
Hole
Lock--out
Button
Chain
Bar
Trigger Switch
Power Cord
TRIGGER SWITCH
BAR OIL CAP/OILER ACTUATOR
The BAR OIL CAP is used to access the
bar oil tank and pressed to supply oil to
chain.
The TRIGGER SWITCH is used to turn on
the unit. Squeeze the trigger switch to
operate the unit after lock--out button
has been pushed in. Release the trigger
to turn the unit off.
CHAIN ADJUSTMENT SCREW
The CHAIN ADJUSTMENT SCREW is
used to adjust the chain tension.
POWER CORD
TRIGGER LOCK--OUT BUTTON
The TRIGGER LOCK--OUT BUTTON is a
control feature designed to prevent the
motor from being accidently started.
When the rear handle is gripped in a
normal cutting position, the trigger
lock--out button can be pushed in by
the thumb, permitting the index finger
to squeeze the trigger. It is not neces-
sary to maintain pressure on the trig-
ger lock--out button once the trigger
has been engaged.
The POWER CORD is used to connect
the chain saw to an approved extension
cord.
CHAIN TENSION
It is normal for a new chainto stretchdur-
ing first 15 minutes of operation. You
should check your chain tension fre-
quently. Readjust chain after every 15
minutes of operation. See CHECK CHAIN
TENSION under the MAINTENANCE sec-
tion.
OPERATING INSTRUCTIONS
Use only a voltage supply as specified on
your unit.
ATTACH THE EXTENSION CORD TO
YOUR CHAIN SAW
To prevent disconnection from unit, se-
cure extension cord to power cord as
shown in the following illustration.
SELECT AN EXTENSION CORD
MINIMUM WIRE GAUGE
RECOMMENDATIONS
50 ft.
100 ft.
25 ft.
Volts
120
(15.24 m) (30.48 m)
(7.67 m)
14
A.W.G.*
16
A.W.G.*
16
A.W.G.*
Extension Cord
*American Wire Gauge
7
BEFORE STARTING SAW
each time it is pressed. For maximum
guide bar and chain life, we recommend
you use Poulan chain saw bar oil. If Pou-
lan bar oil is not available, you may use a
good grade SAE 30 oil until you are able
to obtain Poulan brand. The oil output is
manually metered during operation. Use
a funnel to fill the tank. Replace oil cap se-
curely. Check oil level after every 15 min-
utes of operation.
WARNING: Be sure to read the
electrical safety information in the SAFE-
TY RULES section of this manual before
you begin. If you do not understand the
electrical safety information do not at-
tempt to use your unit. Seek help from
someone that does understand the in-
formation or call the customer assis-
tance help line at 1-800-554-6723.
STOPPING YOUR SAW
GUIDE BAR AND CHAIN OIL
S Release the trigger switch.
The bar and chain require lubrication. The
manually--operated chain oiler provides
lubrication to the chain and guide bar. Be
sure to fill the bar oil tank before each cut-
ting session. The oiler activator/bar oil cap
must be used regularly and often enough
to maintain a thin film of oil on the bar and
chain while saw is cutting. It is recom-
mended that the oiler actuator/bar oil cap
be operated every ten (10) seconds and
held for approximately three (3) seconds
S If motor does not stop, disconnect the
extension cord. Discontinue use of
the unit until repaired by an authorized
service dealer.
STARTING YOUR SAW
1. Connect the saw to a power source
using the proper size extension cord
(see SELECT AN EXTENSION CORD).
2. Push in switch lock out button.
3. Squeeze and hold the trigger switch.
CUTTING METHODS
OPERATING TIPS
TREE FELLING TECHNIQUES
S Check chain tension before first use
and after 1 minute of operation. See
CHECK CHAIN TENSION in the MAINTE-
NANCE section.
WARNING: Check for broken or
dead branches which can fall while cutting
causing serious injury. Do not cut near
buildings or electrical wires if you do not
know the direction of tree fall, nor cut at
night since you will not be able to see well,
nor during bad weather such as rain,
snow, strong winds, etc. If the tree makes
contact with any utility line, the utility com-
plany should be notified immediately.
S Carefully plan your sawing operation in
advance.
S Cut wood only. Do not cut metal, plas-
tics, masonry, non-wood building ma-
terials, etc.
S Stop the saw if the chain strikes a for-
eign object. Inspect the saw and repair
parts as necessary.
S Keep the chain out of dirt and sand.
Even a small amount of dirt will quickly
dull a chain and increase the possibil-
ity of kickback.
S Clear the work area. You need a clear
area all around the tree so you can have
secure footing.
S Practice cutting a few small logs using
the following steps. This will help you
get the “feel” of using your saw before
you begin a major sawing operation.
S Squeeze the trigger switch and allow
unit to reach full speed before cutting.
S Begin cutting with the saw frame
against the log.
S The chain saw operator should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill af-
ter it is felled.
S Study the natural conditions that can
cause the tree to fall in a particular direc-
tion, such as:
S The wind direction and speed.
S The lean of the tree. The lean of a tree
might not be apparent due to uneven
or sloping terrain. Use a plumb or lev-
el to determine the direction of tree
lean.
S Weight and branches on one side.
S Surrounding trees and obstacles.
S Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator.
S Keep the motor at full speed the en-
tire time you are cutting.
S Release trigger switch as soon as cut
is completed, allowing motor to stop.
S Keep the cord away from the cutting
area. Position cord so it will not be
caught on branches and the like
during cutting.
S To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
S Stop motor before setting saw down.
8
Hinge holds tree on stump and helps
control fall
S Make sure there is enough room for
the tree to fall. Maintain a distance of
2-1/2 tree lengths from the nearest per-
son or other objects. Motor noise can
drown out a warning call.
S Remove dirt, stones, loose bark, nails,
staples, and wire from the tree where
cuts are to be made.
Opening
of felling
cut
Closing of
notch
Plan a clear retreat path
NOTE: Before felling cut is complete, use
wedges to open the cut if necessary to
control the direction of fall. To avoid kick-
back and chain damage, use wood or
plastic wedges, but never steel or iron
wedges.
Direction of Fall
45_
S Be alert to signs that the tree is ready
to fall: cracking sounds, widening of
the felling cut, or movement in the up-
per branches.
FELLING LARGE TREES
(6 inches in diameter or larger)
S As tree starts to fall, stop saw, put it
down, and get away quickly on your
planned retreat path.
The notch method is used to fell large
trees. A notch is cut on the side of the
tree in the desired direction of fall. After a
felling cut is made on the opposite side
of tree, the tree will tend to fall in the
direction of the notch.
NOTE: If tree has large buttress roots,
remove them before making the notch. If
using saw to remove buttress roots,
keep saw chain from contacting ground
to prevent dulling of the chain.
NOTCH CUT AND FELLING TREE
S Make notch cut by cutting the top of
the notch first. Cut through 1/3 of the
diameter of the tree. Next complete
the notch by cutting the bottom. See il-
lustration. Once notch is cut, remove
the wedge of wood from the tree.
S DO NOT use your saw to cut down a par-
tially fallen tree. Be extremely cautious
with partially fallen trees that may be
poorly supported. When a tree doesn’t
fall completely, set saw aside and pull
down tree with a cable winch, block and
tackle, or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a
fallen tree to the desired log size.
WARNING: Do not stand on the
log being cut. Any portion can roll caus-
ing loss of footing and control. Do not
stand downhill of the log being cut.
IMPORTANT POINTS
S Cut only one log at a time.
Felling cut here
First cut
S Cut shattered wood very carefully;
sharp pieces of wood could be flung
toward operator.
S Use a sawhorse to cutsmall logs.Nev-
er allow another person to hold the log
while cutting and never hold the log
with your leg or foot.
Notch
Hinge
Second cut
S Do not cut in an area where logs, limbs,
and roots are tangled. Drag logs into a
clear area before cutting them by pulling
out exposed and cleared logs first.
BUCKING TECHNIQUES
S After removing the wood from the
notch, make the felling cut on the op-
posite side of the notch. This is done
by making a cut about two inches
higher than the center of the notch.
This will leave enough uncut wood be-
tween the felling cut and the notch to
form a hinge. This hinge will help pre-
vent the tree from falling in the wrong
direction.
WARNING: If saw becomes
pinched or hung in a log, don’t try to force it
out. You can lose control of the saw, re-
sulting in injury and/or damage to the saw.
Stop the saw; drive a wedge of plastic or
wood into cut until the saw can be re-
moved easily. Restart saw and carefully
9
reenter the cut. Do not use a metalwedge.
Do not attempt to restart your saw when it
is pinched or hung in a log.
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
nd
Use a wedge to remove pinched saw.
2
Cut
Using a log for support
st
1
Cut
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting begins on the top side of
the log with the bottom of the saw
against the log. When overcutting use
light downward pressure.
st
1
Cut
cutting
nd
2
Cut
nd
2
Cut
Using a support stand
Und
Undercutting involves cutting on the
underside of the log with top of saw
against the log. When undercutting use
light upward pressure. Hold saw firmly
and maintain control. The saw will tend
to push back toward you.
st
1
Cut
WARNING: Never turn saw upside
down to undercut. The saw cannot be
controlled in this position.
Always make your first cut on the com-
pression side of the log. The compres-
sion side of the log is where the pressure
of the log’s weight is concentrated.
First cut on compression side of log
st
1
Cut
nd
2
Cut
LIMBING AND PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the mov-
ing chain to contact any other branches
or objects at the nose of the guide bar
when limbing or pruning. Allowing such
contact can result in serious injury.
Second cut
Second cut
WARNING: Never climb into a tree
to limb or prune. Do not stand on lad-
ders, platforms, a log, or in any position
which can cause you to lose your bal-
ance or control of the saw.
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter of
the log.
S Roll the log over and finish with a sec-
ond overcut.
S Watch for logs with a compression
side. See illustration above for cutting
logs with a compression side.
BUCKING USING A LOG OR
SUPPORT STAND
S Remember your first cut is always on
the compression side of the log.(Refer
to the illustrations for your first and
second cut)
IMPORTANT POINTS
S Watch out for springpoles. Spring-
poles are small size limbs which can
whip toward you or pull you off bal-
ance. Use extreme caution when cut-
ting small size limbs.
S Be alert for springback from any
branches that are bent or under pres-
sure. Avoid being struck by the branch
or the saw when the tension in the
wood fibers is released.
S Frequently clear branches out of the
way to avoid tripping over them.
10
LIMBING
PRUNING
WARNING: Limit pruning to limbs
S Limb a tree only after it is cut down.
S Leave the larger limbs underneath the
felled tree to support the tree as you
work.
shoulder height or below. Do not cut if
branches are higher than your shoulder.
Get a professional to do the job.
S Make your first cut 1/3 of the way
through the bottom of thelimb. Thiscut
will make the limb sag so that it falls
easily on the second cut.
S Start at the base of the felled tree and
work toward the top, cutting branches
and limbs. Remove small limbs with
one cut.
S Keep the tree between you and the
chain.
S Remove larger branches with the cut-
ting techniques described in BUCKING
WITHOUT A SUPPORT.
S Always use an overcut to cut small
and freely hanging limbs. Undercut-
ting could cause limbs to fall and pinch
the saw.
S Next make a second cut all the way
through the limb.
S Finish the pruning operation by using
an overcut so that the stump of the
limb protrudes 1 to 2 inches from the
trunk of the tree.
Second cut
First cut
1/3 of way
3rd cut 1 to 2 in.
from trunk of tree
MAINTENANCE
CUSTOMER RESPONSIBILITIES
WARNING: Disconnect power source before performing maintenance.
Fill in dates as you complete
regular service
Before
Use
After
Use
Every
15 min.
Service
Dates
Check for damaged/worn parts
n
Check for loose fasteners/parts
Check chain tension
n
n
n
Check chain sharpness
Check guide bar
n
n
Check bar and chain oil level
Inspect and clean unit & labels
Clean guide bar groove
n
n
n
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to oper-
ator abuse or negligence. To receive full
value from the warranty, the operator
must maintain unit as instruct- ed in this
manual. Various adjustments will need
to be made periodically to properly
maintain your unit. Improper mainte-
nance may cause damage to the unit
and possible injury to the operator or by-
standers.
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for
replacement of damaged or worn parts.
NOTE: It is normal for a small amount of
oil to appear under the saw after motor
stops. Do not confuse this with a leaking
oil tank.
S Trigger Switch -- Ensure the trigger
switch functions properly by squeez-
ing and holding the trigger switch.
Make sure motor starts and stops.
11
S Oil Tank -- Discontinue use of chain
saw if oil tank shows signs of damage
or leaks.
S Power Cord -- Discontinue use if chain
saw power cord shows signs of dam-
age or wear.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Bar Mounting Nut
S Chain
S Bar Adjusting Screw
6. Continue turning the adjusting
screw until the tension is correct
(see step 4).
CHECK CHAIN TENSION
WARNING:
Wear protective
7. Tighten bar mounting nuts with a
wrench.
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
8. Recheck chain tension.
Chain tension is very important. Chain
stretches during use. This is especially
true during the first few times you use your
saw. Always check chain tension each
time you use your saw.
1. Unplug unit from the power source.
2. Use a screwdriver to move chain
around guide bar to ensure kinks do
not exist. The chain should rotate
freely.
WARNING: If the saw is operated
with a loose chain, the chain could jump
off the guide bar and result in serious in-
jury.
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A dull
chain makes a sawdust powder and
cuts slowly. See CHAIN SHARPENING in
the SERVICE AND ADJUSTMENTS section.
CHECK GUIDE BAR
Conditions which require guide bar
maintenance:
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
S Inadequate supply of oil to the bar and
chain.
Check the condition of the guide bar
each time the chain is sharpened. A
worn guide bar will damage the chain
and make cutting difficult.
NOTE: It is recommended that the saw
be turned upside down for chain
tensioning.
3. Loosen bar mounting nuts until they
are finger tight.
4. Turn the adjusting screw clockwise
until the chain solidly contacts bot-
tom of guide bar rail. Then, turn ad-
justing screw an additional 1/4 turn.
This is correct chain tension setting.
After each use, with unit disconnected
from power source, clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
S Disconnect the chain saw from the
power source.
Adjusting Screw -- 1/4 Turn
S Loosen and remove bar mounting
nuts. Remove bar, bar clamp plate
and chain from saw.
S Clean the oil holes and bar groove af-
ter each 5 hours of operation.
NOTE: To tighten the chain, turn the
adjusting screw clockwise; to loosen the
chain, turn the adjusting screw counter-
clockwise.
ve Sawdust From
de Bar Groove
Adjusting Screw
Oil Holes
S Burring of guide bar rails is a normal
process of rail wear. Remove these
burrs with a flat file.
S When rail top is uneven, use a flat file
to restore square edges and sides.
5. Check the tension by lifting the chain
from the guide bar. Remove some of
the stiffness in the chain by pulling
down on the chain several times.
12
S Check bar and chain oil before use
and every 15 minutes while operating
the saw. See GUIDE BAR AND CHAIN
OIL under the OPERATION section.
INSPECT AND CLEAN UNIT AND
LABELS
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
Replace the guide bar when the groove
is worn, the guide bar is bent or cracked,
or when excess heating or burring of the
rails occurs. If replacement is neces-
sary, use only the guide bar specified for
your saw in the repair parts list or on the
decal located on the chain saw.
S After each use, inspect complete unit
for loose or damaged parts. Clean the
unit and labels using a damp cloth with
a mild detergent.
S Wipe off the unit and labels with a
clean dry cloth.
LUBRICATION
Bar Oil Fill Cap
SERVICE AND ADJUSTMENTS
CHAIN SHARPENING
NOTE: The chain has both left
and right hand cutters.
WARNING: Improper chain sharp-
ening techniques and/or depth gauge
maintenance will increase the chance of
kickback which can result in serious injury.
File Holder
File
90˚
Cutter
WARNING: Wear protective gloves
when handling chain. The chain is sharp
and can cut you even when it is not mov-
ing.
Conditions which indicate the need for
chain sharpening:
Depth Gauge
S
Align the 30˚ file holder marks
parallel with the bar and to the
center of the chain.
Cutter
S Reduction in size of wood chips. The
size of the wood chip will decrease as
the chain gets duller until it becomes
more like a powder than a chip. Note
that dead or rotted wood will not pro-
duce a good chip.
30˚
Cutter
Sharpen cutters on one side of the
chain first. File from the inside of
each cutter to the outside. Then,
turn the chain saw around and re-
peat the process for the other side
of the chain.
File Holder Line
S
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
Tools required:
S 5/32 inch (4 mm) diameter round file
and file holder
S Flat file
S
S
S
File on the forward stroke only. Use
2 or 3 strokes per cutting edge.
Keep all cutters the same length
when filing.
S Depth gauge tool
TO SHARPEN CHAIN:
1. Move ON/STOP switch to the STOP
position.
File enough to remove any dam-
age to cutting edges (side plate
and top plate of cutter).
2. Check chain for proper tension. Ad-
just chain tension if necessary. See
CHECK CHAIN TENSION section.
3. Sharpen cutters.
Remove Damage
All Cutters
Same Length
S
To sharpen the cutters, position
the file holder level (90˚) so that it
rests on the top edges of the cut-
ter and depth gauge.
Top Plate
Side Plate
13
S
File chain to meet the specifica-
tions as shown.
It is normal for a new chainto stretchdur-
ing the first 15 minutes of operation. You
should recheck your chain tension fre-
quently and adjust the chain tension as
required. See CHECK CHAIN TENSION
section.
80˚
60˚
Replace the old chain when it becomes
worn or damaged. Use only the Low
Kickback replacement chain specified
in the list of available replacement parts.
The chain must complywith kickback re-
quirements of ANSI B175.1 when tested
with this saw.
30˚
Hook Angle
0.025 inch
(0.65 mm)
Rounded
Corner
See an authorized service dealer to re-
place and sharpen individual cutters on
your chain.
Right
Squared Off
Corner
Too Much Hook Angle
TO REPLACE CHAIN:
1. Disconnect the chain saw from the
power source.
2. Turn the unit upside down on a flat
surface. Straighten out chain, then
lay it on a flat surface.
Wrong
WARNING: Maintain the proper
hook angle according to the manufactur-
er’s specifications for the chain you are
using. Improper hook angle will increase
the chance of kickback which can result in
serious injury.
Adjusting
Screw
4. Check and lower depth gauges.
Bar Nuts
File
Depth Gauge Tool
3. Remove bar mounting nuts, bar
clamp plate, and old chain.
Depth Gauge
4. Turn the adjusting screw counter-
clockwise to move the adjusting pin
almost as far as it will go to the rear.
Do not remove the adjusting screw
from the unit.
S
S
Place gauge tool on cutter.
If the depth gauge is higher than
the depth gauge tool, file it level to
the top of the depth gauge tool.
Maintain rounded front corner of
depth gauge with a flat file.
5. Hold chain with cutters facing as
shown.
S
NOTE: The very top of the depth
gauge should be flat with the front
half rounded off with a flat file.
Tip of
Bar
If you require further assistance or are un-
sure about performing this procedure,
contact your authorized service dealer or
call our customer assistance help line at
1--800--554--6723.
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
WARNING: Avoid accidental start-
ing. Always unplug saw from power
source before installing a bar and/or
chain.
Depth Gauge
Cutters
CHAIN REPLACEMENT
WARNING:
Wear protective
gloves when handling chain. The chain
is sharp and can cut you even when it is
not moving.
Drive Links
14
6. Slide the chain between the housing
and the sprocket. Place chain
around the sprocket and fit the drive
links into the guide bar groove and
then around guide bar nose.
CHAIN ADJUSTMENT
See CHECK CHAIN TENSION in the MAIN-
TENANCE section.
CUSTOMER SERVICEABLE PARTS
Sprocket
WARNING: Use of any other ac-
cessory or attachment might present a
risk of injury to the operator.
Bar
REPLACEMENT PART
PART NO.
Right Housing
Bar Mounting Nuts
Oil Cap
Guide Plate
Safety Lock Button
Bar Adjusting Screw
Bar Adjusting Pin
530015251
530029282
530029285
530025873
530015514
530023492
530015832
530015835
952055085
952051209
952051211
952044368
952044370
952030129
7. Hold the guide bar against the saw
frame and install the bar clampplate.
Be sure the tab on the bar clamp
plate is toward the rear of bar.
Adjusting Pin Slot
Tab
Spacer
Spacer Screw
Bar
Clamp
Plate
File (5/32″ dia.) Twin Pak
Xtra GUARD® Chain --14″
Xtra GUARD® Chain -- 16″
Lo--Kick® Guide Bar -- 14″
Lo--Kick® Guide Bar -- 16″
Bar & Chain Lubricant --1 qt.
Bar Nuts
8. Secure the guide bar and bar clamp
plate with the bar nuts; tighten finger
tight only.
CAUTION: If saw chain is installed
backwards, the saw will vibrate exces-
sively and will not cut wood.
Bar & Chain Lubricant --1 gal. 952030130
STORAGE
SEASONAL STORAGE
Prepare your unit for storage at the
end of the season or if it will not be
used for 30 days or more.
If your chain saw is to be stored for a
period of time:
WARNING: Perform the following
steps after each use:
S Allow the motor to cool before storing
or transporting.
S Store chain saw and extension cord in
a well ventilated area
S Clean it thoroughly before lengthy stor-
age.
S Store chain saw with all guards in
place and position chain saw so that
any sharp object cannot accidentally
cause injury.
S Store in a clean dry area.
S Lightly oil external metal surfaces and
guide bar.
S Store chain saw unplugged, well out of
the reach of children.
S Oil the chain and wrap it in heavy pa-
per or cloth.
S Use bar sheath to cover bar.
15
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source be-
fore performing all of the recommended remedies below except remedies
that require unit to be operating.
TROUBLE
CAUSE
REMEDY
Chain does 1. Chain tension incorrect.
not move
1. See “Check Chain Tension” in
Maintenance section.
2. Repair or replace.
3. Contact an authorized service
dealer.
4. Reset circuit breaker or replace
fuse.
when trigger 2. Guide bar rails pinched.
switch is
engaged.
3. Trigger switch failure.
4. Circuit breaker tripped/
fuse failure.
Chain clat-
ters or cuts
roughly.
1. Chain tension incorrect.
1. See “Check Chain Tension” in
Maintenance Section.
2. Cutters damaged.
2. Contact an authorized service
dealer.
3. Chain worn.
3. Resharpen or replace chain.
4. See “Chain Sharpening” in
Service and Adjustments section.
4. Cutters dull, improperly
sharpened, or depth
gauges too high.
5. Sprocket worn.
5. Contact an authorized service
dealer.
Chain stops 1. Chain cutter tops not
1. See “Chain Sharpening” in
Service and Adjustments section.
2. Repair or replace guide bar.
during cut.
filed flat.
2. Guide bar burred or
bent; rails uneven.
1. Fill oil tank.
Oil inade-
1. Oil tank empty.
2. Contact an authorized service
dealer.
quate for bar 2. Oil outlet clogged.
and chain
3. Remove bar and clean.
lubrication.
3. Guide bar oil hole
blocked.
Chain cuts
at an angle.
1. Cutters damaged on
one side.
1. See “Chain Sharpening” in
Service and Adjustments section.
2. Chain dull on one side. 2. See “Chain Sharpening” in
Service and Adjustments section.
3. Guide bar bent or worn. 3. Replace guide bar.
16
WARRANTY STATEMENT
Poulan, a division of Husqvarna Con-
In Canada, contact:
Poulan
sumer Outdoor Products N.A., Inc.,
warrants to the original consumer pur-
chaser that each new Poulan brand
electric or cordless product is free from
defects in material and workmanship
and agrees to repair or replace under
this warranty any defective Poulan
brand electric product within one (1)
year from the original date of pur-
chase.
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number
and date of purchase of your product and
the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC LE-
GAL RIGHTS, AND YOU MAY HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED, AND
THERE ARE NO OTHER EXPRESS WAR-
RANTIES EXCEPT THOSE EXPRESSLY
STIPULATED HEREIN.
If your Poulan brand electric or cordless
product should fail within the limited war-
ranty period, you may return it in com-
plete condition, prepaid, with proof of
purchase to the dealer from whom it was
purchased for repair or replacement at
the option of Poulan.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or alteration, or the use of
accessories and/or attachments not
specifically recommended by Poulan
for this product. This warranty does not
cover parts that will wear and require re-
placement with reasonable use during
the warranty period. This warranty does
not cover pre--delivery setup or normal
adjustments explained in the instruction
manual.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMI-
TATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the
meaning of that term as defined in the
Magnuson--Moss Act of 1975.
The policy of Poulan is to continuously
improve its products. Therefore, Poulan
reserves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice orobligation to any
purchaser.
Should you have any unanswered
questions regarding this warranty,
please contact:
Poulan, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554--6723
17
|