Poulan Lawn Mower Accessory 178478 User Manual

.  
.
t
t  
.  
t
t
t
.
t
f
t
r.  
e
in  
ta  
n
o
t
n
c
e
m
ce  
la  
p
e
r
ed  
d
n
e
m
m
co  
e
r
a
ly  
n
o
se  
U
d.  
e
g
a
m
a
d
r
o
d
e
k
c
a
cr  
n
e
h
w
ce  
la  
p
f
t
OWNER’S MANUAL  
Model No. LTB48A  
Product No. 964 77 62-00  
48 Inch Mower  
Grass Catcher  
• Assembly  
• Operation  
• Customer Responsibilities  
• Repair Parts  
178478 Rev. 4 11.20.03 rad  
Printed in U.S.A.  
 
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
Be sure the area is clear of other people before mowing.  
Stop machine if anyone enters the area.  
Look for this symbol to point out  
important safety precautions. It means  
CAUTION!!! BECOME ALERT!!! YOUR  
SAFETY IS INVOLVED.  
Never carry passengers or children even with the blades  
off.  
Do not mow in reverse unless absolutely necessary.Always  
look down and behind before and while backing.  
Never carry children. They may fall off and be seriously  
injured or interfere with safe machine operation.  
Keepchildrenoutofthemowingareaandunderthewatchful  
care of another responsible adult.  
CAUTION: Do not coast down a hill  
in neutral, you may lose control of  
the tractor.  
Be alert and turn machine off if children enter the area.  
Before and when backing, look behind and down for small  
children.  
Mow up and down slopes (15° Max), not across.  
Remove obstacles such as rocks, tree limbs, etc.  
Watchforholes,ruts,orbumps.Uneventerraincouldoverturn  
the machine. Tall grass can hide obstacles.  
Use slow speed. Choose a low gear so that you will not  
have to stop or shift while on the slope.  
Avoid starting or stopping on a slope. If tires lose traction,  
disengage the blades and proceed slowly straight down the  
slope.  
CAUTION:Towonlytheattachments  
that are recommended by and  
comply with specifications of  
the manufacturer of your tractor.  
Use common sense when towing.  
Operate only at the lowest possible  
speed when on a slope. Too heavy  
of a load, while on a slope, is  
dangerous. Tires can lose traction  
with the ground and cause you to  
lose control of your tractor.  
If machine stops while going uphill, disengage blades, shift  
into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
CAUTION: In order to prevent  
accidental starting when setting  
up,transporting,adjustingormaking  
repairs, always disconnect spark  
plug wire and place wire where it  
cannot contact spark plug.  
CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to  
give you the best possible dependability and performance.  
Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center/  
department. They have competent, well trained technicians and the proper tools to service or repair this unit.  
Please read and retain this manual.The instructions will enable you to assemble and maintain your Grass Catcher properly.  
Always observe the "SAFETY RULES".  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
CARTON CONTENTS.................................................... 4  
ASSEMBLY.................................................................5-7  
OPERATION .................................................................. 8  
CUSTOMER RESPONSIBILITIES................................. 9  
STORAGE...................................................................... 9  
REPAIR PARTS.......................................................10-11  
3
 
KNOWYOUR GRASS CATCHER  
READTHISOWNER'SMANUALANDSAFETYRULESBEFOREASSEMBLINGOROPERATINGYOURGRASSCATCHER.  
Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study  
the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to  
prevent injury to yourself and others. Save this manual for future reference.  
The operation of any tractor can result in foreign objects thrown into the eyes,  
which can result in severe eye damage. Always wear safety glasses or eye shields  
before starting your tractor and while mowing. We recommend a wide vision safety  
mask for over the spectacles or standard safety glasses.  
TOOLS REQUIRED FOR ASSEMBLY  
UNPACKING INSTRUCTIONS  
(1) 9/16" Wrench  
Remove all parts and packing materials from carton.  
Check carton contents against list. Be sure all parts  
are there.  
SHOULDER  
BOLTS  
SUPPORT  
ASSEMBLY  
CARTON CONTENTS:  
(3) Container Tops  
(3) Container Bottoms  
(1) Upper Chute  
(1) Support Assembly  
(1) Cover Assembly  
(2) Shoulder Bolts  
(1) Retainer Spring  
(1) Lower Chute  
PARTS IDENTIFICATION  
RETAINER  
SPRING  
COVER  
ASSEMBLY  
t
.
.  
.
t
DUMP BAG  
INDICATOR  
.
t
.
t
r.  
e
in  
ta  
n
o
t
n
c
e
m
t
ce  
la  
p
e
r
d
e
d
n
e
m
m
co  
e
r
a
ly  
n
o
se  
U
d.  
e
g
a
m
a
d
r
o
d
e
k
c
a
cr  
n
e
h
w
ce  
la  
CHUTE LATCH  
02079  
UPPER CHUTE  
GRASS  
CATCHER  
CONTAINERS  
LOWER CHUTE  
ATTACHING  
STRAPS  
LOWER CHUTE  
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the  
tractor, in the operator's position.  
CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR:  
Depress clutch/brake pedal fully and set parking brake.  
Place gearshift/motion control lever in "NEUTRAL" position.  
Place attachment clutch in "DISENGAGED" position.  
Turn ignition key "OFF" and remove key.  
Make sure the blade and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
4
 
ASSEMBLY  
MOUNTING COVER ASSEMBLY TO  
SUPPORT ASSEMBLY (See Fig. 2)  
NOTE: For ease of assembly, you may wish to obtain the  
assistance of another person for mounting coverassembly  
to tractor.  
BAGGER SUPPORT ASSEMBLY  
(See Figs. 1A & 1B)  
2
1
1. Remove and discard the upper bolt on both sides of  
the drawbar.Using the same holes, install the shoulder  
bolts supplied and tighten securely.  
1. Position cover assembly on ground behind tractor as  
shown.  
2. Liftandrotatecovertoaligncoverbracketswithsupport  
assembly tubes.  
3. Slide cover assembly down onto the support tubes.  
REMOVE AND DISCARD  
UPPER BOLTS AND INSTALL  
SHOULDER BOLTS SUPPLIED  
COVER  
ASSEMBLY  
1
253  
0
DRAWBAR  
FIG. 1A  
SUPPORT  
ASSEMBLY  
2. Align support assembly pin with hole in drawbar and  
hang assembly over the shoulder bolts.  
3. Besuresupportassemblyisseatedproperlyandsecure  
with retainer spring supplied.  
SHOULDER  
BOLTS  
SUPPORT  
ASSEMBLY  
RETAINER  
SPRING  
PIN  
FIG. 1B  
02532  
FIG. 2  
5
 
CONTAINER ASSEMBLY (See Fig. 3)  
CONTAINER MOUNTING (See Fig. 4)  
3
4
1. Place bottom half inside of top half, as shown.  
2. Place one foot inside bottom half and lift top half to  
meet bottom half.  
1. Install one container to left side first with warning to  
outside of unit. Install another container to center  
position and one in right position.  
NOTE:Rightcontainershouldalwaysoverlapleftcontainer  
at center supports.  
3. Press halves tightly together while lifting top to lock  
into place as shown.  
2. Close cover and lock latch handles over center support  
tubes.  
IMPORTANT:BEFORELOCKINGTHETABS,HOOKEDEDGES  
ONBOTHHALVESMUSTOVERLAPTOFORMSEALASSHOWN  
IN INSET.  
4. Repeat for other containers.  
CONTAINER  
BOTTOM HALF  
COVER LATCH  
HANDLES  
2089  
0
CONTAINER  
WARNING  
CONTAINER  
TOP HALF  
CENTER  
SUPPORT  
TUBES  
s  
r
n
e
i
h
w
r.  
e
e
c
l
a
i
n
p
l
t
a
n
o
c
Re  
.  
t
t
n
y
r
e
n
e
m
e
u
r
ce  
la  
b
fr  
p
a
g
r
e
c
e
m
in  
a  
k
ed  
d
en  
m
c
Ch  
s
.
n
r
s
o
o
t
i
o
c
o
n
a
e
u
r
a
ri  
w
ie  
l
y
o
t
n
m
e
d
.
e
n
d
s
r
a
U
a
e
r
d
a
e
g
a
e
t
w
r
no  
to  
m
t
da  
D
o
e
c
j
o
b
d
u
e
k
s
c
ra  
c
PRESS TOGETHER  
TO FORM SEAL  
is  
r
n
e
e
in  
ta  
e
n
c
h
CONTAINER  
WHILE LIFTING  
TOP HALF  
.Co  
ll la  
ta  
n
e
m
w
r.  
e
d
e
i
n
ta  
p
s
n
Re  
o
is y.  
tl  
t
n
c
y
q
rl  
e
n
e
e
p
u
ro  
e
lac  
p
b
is  
fr  
p
ag re  
r
e
c
e
m
in  
ta  
k
e
d
d
n
o
en  
c
Ch  
m
s
.
n
r
s
o
o
l
e
t
i
o
c
o
n
a
e
u
r
CONTAINER  
WARNING  
e
r
r
i
a
w
ie  
l
y
o
t
e
n
NG  
m
I
d
.
e
Us  
N
t
e
n
d
r
a
a
e
r
d
AR  
p
a
e
g
a
o
e
t
w
r
Wno  
to  
m
t
da  
D
o
e
c
j
o
b
d
u
e
k
s
c
ra  
c
TOP HALF  
CONTAINER  
HANDLE  
FIG. 4  
CONTAINER  
BOTTOM  
HALF  
LOCKING  
TAB  
FIG. 3  
ASSEMBLY CHECK: Squeeze sides of lower half of con-  
tainer and check that there is no gap between upper and  
lower halves. If a gap appears, unlock tabs to separate  
container halves and repeat instructions above.  
e
u
eq  
com  
r
e
m
e
rop  
g
f
y
r
p
a
is  
er ck nl  
b
a
n
o
ai  
he  
nt  
co ion  
r
.
C
s
e
.
U
d
e
ss rat  
le io  
g
ma  
a
n
d
u
ie  
d
.
r
t
e
a
c
e
d
w
r
or  
N
G
m
o
n
d
N
I
t
e
c
ke  
r
a
a
r
a
e
r
R
e
h
A t ope  
w
n
en tai  
con  
Wno  
t
a
c
t
o
ec  
w
o
j
ce  
D
ub  
ss epl  
yi  
ent  
m
e
rl  
e
n
.
R
a
tly pl  
re  
n
d
d
e
02097  
6
 
UPPER CHUTE (See Figs. 6A & 6B)  
LOWER CHUTE (See Fig. 5)  
5
6
1. Raise and hold deflector shield in upright position.  
2. Place slot in lower chute over tab on mower deck and  
position lower chute over deck opening as shown.  
1. Lower mower deck to its lowest cutting position.  
2. Assemble upper chute by inserting curved end into  
hole in back of cover.  
3. Hook rear latch into flange hole on back of mower  
deck.  
NOTE: Handle carefully so as not to damage dump bag  
indicator.  
4. Hook front latch into tab hole on front of mower deck.  
3. Push in and turn upper chute until it is in line with lower  
chute.  
4. Align the bosses on lower chute with alignment slots  
on upper chute and slide together.  
5. Secure with rubber latch by hooking hole in latch over  
latch pin.  
CAUTION: Do not remove deflector  
shield from mower. Raise and hold  
shield when attaching lower chute  
and allow it to rest on chute while in  
operation.  
DUMP BAG  
INDICATOR  
UPPER  
CHUTE  
HANDLE  
COVER  
DEFLECTOR  
SHIELD  
OPTIONAL FRONT  
GAUGE WHEEL  
TAB  
LOWER  
CHUTE  
FIG. 6A  
ALIGNMENT  
SLOT  
LATCH PIN  
RUBBER  
LATCH  
FRONT  
LATCH  
BOSSES  
FIG. 6B  
REAR LATCH  
LEVEL MOWER DECK  
7
Besuredeckisproperlyleveledforbestmowerperformance.  
See your tractors owner's manual for instructions.  
FIG. 5  
7
 
OPERATION  
Avoid cutting wet grass or in the morning while the dew  
TIPS FOR IMPROVED BAGGING  
OPERATION:  
is still heavy. Grass clippings collected under these  
conditions tend to be sticky and adhere to the walls of  
the flow path causing clogging.  
Follow the mower operation instructions in your tractor  
owner's manual.  
Your bagger is equipped with a dump bag indicator.As  
the bags become full, the flow indicating ball will drop  
down in its slot, indicating that the bags are full or the  
chutes have become clogged. Care should be taken  
not to damage the parts and that the ball moves freely  
at the beginning of each use.  
When operating your grass catcher on a lawn where grass  
and leaf bagging equipment has not been used, you are  
picking up thatch and debris that has accumulated for long  
periods of time. The amount collected and the total time  
of operation may be greater than you will experience with  
regular use of your grass catcher.  
NOTE: To help prevent clogging of chutes, check/empty  
bags when ball begins to drop down in the slot.Experience  
will teach you the best time to empty the bags.  
Always run throttle at full speed when bagging.  
Select a gear low enough to give good mower cutting  
performance, good quality cut and good bagging  
performance.  
If the grass catcher fails to pick up cut grass or leaves,  
it is an indication that clogging has occurred in the  
system or that the grass catcher containers are full.  
a. Disengage blades, shift into neutral, engage the  
parking brake and stop the engine.  
NOTE: It may be necessary to overlap width of cut to suit  
your conditions.  
- Raise seat. Unlatch and raise cover.  
- Slide out containers and dispose of clippings .  
- Replace containers, close cover, and latch.  
b. Unlatch chutes and check for clogging  
- Remove all debris in chutes.  
If grass is extremely tall, it should be mowed twice.The  
first time relatively high, the second time to desired  
height.  
Use left hand side of mower for trimming.  
Plastic trash bags can be inserted inside grass catcher  
containers for ease of debris disposal. To remove the  
plastic trash bags when full:  
a. Disengage blades, shift into neutral, engage the  
parking brake and stop the engine.  
- Reassemble and latch chutes  
c. Checktoinsuredumpbagindicatorhasnotbecome  
clogged.  
b. Raise seat. Unlatch and raise cover.  
- The air passage hole must be clear of debris.  
Gentlyinsertasmalltwigorwireintopassageway  
to clear.  
c. Remove one container at a time by grasping  
container handles and pulling toward the rear, off  
of the tube rails.  
d. With the container resting on the ground, close  
and secure the top of the plastic lawn bag.  
CAUTION  
e. Tip the container on its side and slide the filled bag  
from the container.  
f. Install a new plastic lawn bag with the edges of the  
bag draped over upper lip of the container.  
g. Repeat for other containers.  
h. Reinstall containers making sure right container  
overlaps left container at center supports.  
• Do not operate mower with grass catcher  
partially installed.  
• Disengage blades and stop engine before  
leaving tractor seat to empty containers,  
unclogging chutes, etc.  
• Close cover before starting.  
j. Closecoverandsecurelatchesovercentersupport  
tubes.  
• Disengage mower when crossing driveways  
or gravel surfaces and other areas where  
thrown objects could be a hazard.  
• Do not attempt to vacuum up cans or other  
potentially hazardous projectiles.  
8
 
CUSTOMER RESPONSIBILITIES  
STORAGE  
GENERAL RECOMMENDATIONS  
When grass catcher is to be stored for a period of time,  
clean it thoroughly, remove all dirt, grass, leaves, etc.Store  
in a clean, dry place.  
Always observe safety rules when performing any main-  
tenance.  
Before each use check for loose fasteners.  
Clean unit thoroughly after each use.  
CAUTION: Donotleavegrassinbagger  
containers. Emptycontainersaftereach  
useandbeforestoring. Failuretodoso  
mayresultinspontaneouscombustion  
which could develop into a fire.  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
See BLADE CARE instructions in your tractor owner's  
manual.  
CAUTION:BEFOREPERFORMINGANY  
MAINTENANCE,SERVICEORADJUST-  
MENTS:  
Depress clutch brake pedal fully and  
set parking brake.  
Place gearshift/motion control lever in  
"NEUTRAL" position.  
Placeclutchcontrolin"DISENGAGED"  
position.  
Turn ignition key to "OFF" position.  
Make sure blades and all moving parts  
have completely stopped.  
Disconnect spark plug wire(s) from  
spark plug(s) and place wire where it  
cannot come in contact with plug.  
CAUTION: Grass catcher components  
are subject to wear, damage and  
deterioration, which could expose  
moving parts or allow objects to be  
thrown. Frequentlycheckcomponents  
and replace with manufacturer's  
recommended parts, when necessary.  
9
 
REPAIR PARTS/PIÈCES DE RECHANGE  
GRASS CATCHER - - MODEL NUMBER LTB48A / RAMASSE-HERBE - - NUMÉRO DE MODÈLE LTB48A  
PRODUCT NUMBER 964 77 62-00 / NUMÉRO DE PRODUIT 964 77 62-00  
3
5
20  
2
6
7
34  
4
8
10  
2
20  
12  
13  
9
20  
9
37  
11  
20  
38  
14  
39  
40  
18  
20  
15  
20  
16  
40  
2
2
15  
W A  
R N  
D
s
o
n o t  
20  
9
I
N
u b  
o p e r  
o t  
o
G
j
e c t  
c r  
a
a c  
e t  
k e  
m
w e  
r
o w  
d
a
e
r
r
a n d d a m a g e d .  
u
n l  
e s  
d
e t  
s
a
y
i e r  
s e  
o n l  
a
c o n t  
o
i
r
U
a
t
i n  
o
i
e
r
n
.
C
s i  
b a  
h e c  
p
r
g
r
e
12  
o p e r  
k
c o  
40  
m m e n d e d  
y l  
s i  
n s t e q u e n t  
r
f
a l  
d .  
e
l
e
r e p l  
l y  
C
.
R
a c  
o
n t  
p l a c e e m e n t  
a i  
n e r  
2
w
a i  
s i  
h
c o n t  
20  
e n  
n
e
. r  
14  
33  
16  
2
26  
35  
is  
r
e
e
e
in  
h
in  
ta  
w
t
a
n
e
n
o
c
n
r
o
c
.C  
d
.
e
e
32  
ll  
R
ta  
.
t
ly  
e
la  
s
p
t
n
n
la  
is  
e
p
e
r
ly  
q
r
e
e
fr  
d
e
n
p
ro  
u
me  
p
b
c
is  
r
g
d
e
e
a
in  
ta  
.
re  
n
n
ck  
o
o
a
n
c
ti  
l
y
n
h
o
s
C
c
s
le  
io  
mme  
n
e
u
ti  
a
r
r
e
e
d
G
r
w
d
N
I
mo  
o
N r te  
e
s
U
a
n
R pe  
a
31  
A t o  
r
.
a
d
Wno  
e
ge  
ma  
a
o
w
o
t
t
D
c
d
je  
r
b
o
u
a
d
s
e
k
c
cr  
is  
r
e
e
e
in  
h
in  
ta  
w
t
a
n
e
n
o
c
n
r
o
c
.C  
d
.
e
e
ll  
ta  
.
t
ly  
e
la  
s
p
t
n
n
la  
is  
e
p
e
r
R
e
ly  
q
r
e
e
fr  
d
e
d
n
p
ro  
u
m
c
is  
k
p
b
r
c
g
e
e
a
in  
ta  
n
n
o
o
n
mme  
c
h
o
s
C
c
s
.
le  
io  
n
e
ti  
re  
u
ti  
a
r
r
e
e
G
r
w
d
ge  
a
N
o
n
l
y
n
I
m
o
N r te  
d
e
s
a
R pe  
a
U
A t o  
r
.
d
a
Wno  
e
a
m
a
to  
o
w
t
Do  
c
d
je  
r
b
c
u
d
s
c
ke  
a
r
33  
31  
29  
28  
31  
29  
36  
30  
 
REPAIR PARTS/PIÈCES DE RECHANGE  
GRASS CATCHER - - MODEL NUMBER LTB48A / RAMASSE-HERBE - - NUMÉRO DE MODÈLE LTB48A  
PRODUCT NUMBER 964 77 62-00 / NUMÉRO DE PRODUIT 964 77 62-00  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
Nut, Crownlock #10-24  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
2
3
4
532069180  
532127533  
532139850  
Écrou auto-serrant #10-24  
Écran de couvercle  
Couvercle  
(Y compris 3, 37,38,39)  
Glissière supérieure  
18 532174345  
20 871161010  
26 532124670  
28 532179534  
29 532176997  
30 532165898  
31 532174083  
32 532176990  
33 532128600  
34 532127534  
35 532183286  
36 532129586  
37 532134637  
38 532130895  
39 532186601  
40 871141008  
- - 532178478  
Chute, Lower  
Glissière inférieure  
Vis #10-24 x 5/8  
Ressort de retenue  
Ensemble du support  
Screen, Cover  
Screw #10-24 x 5/8  
Spring, Retainer  
Support Assembly  
Cover Assembly  
(Includes 3, 37, 38, 39)  
Chute, Upper  
Screw, Special #10-14x1/2 Vis spéciale #10-14x1/2  
Dump Bag Indicator  
Screw, #10-24 x 1-1/8  
5
6
7
8
9
532176741  
818021008  
532140572  
532087175  
819061216  
Shoulder Bolt,Self Tapping Boulon autotaraudeuse  
Spring, Retainer  
Plug, Tubing End  
Bagger, Frame  
Pin, Hinge  
Gasket, Cover  
Container, Top  
Container, Bottom  
Seal, Cover  
Latch Handle, Cover  
Strip, Reinforcement  
Screw #10-24 x 1/2  
Owner's Manual  
Ressort de retenue  
Indicateur de sac plein  
Vis #10-24 x 1-1/8  
Capuchon d’extrémité de tuyau  
Cadre de ramasse-herbe  
Goupille de charnière  
Garniture de couvercle  
Bac à gazon supérieur  
Bac à gazon inférieur  
Sceau de couvercle  
Poignée de loquet de couvercle  
Bande  
Washer 3/16x3/4x16 Ga. Rondelle 3/16x3/4x16 Ja.  
10 532007206  
11 532060867  
12 810071000  
13 532109808  
14 532125004  
15 532130760  
16 532130759  
Spacer, Split  
Nut, Acorn #10-24  
Washer, lock  
Latch, Chute  
Nut, Weld  
Entretoise fendue  
Écrou borgne #10-24  
Rondelle frein  
Loquet de glissière  
Axe de loquet  
Latch, Hook  
Rubber, Latch  
Crochet de loquet  
Loquet de caoutchoc  
Vis #10-24 x 1/2  
Manuel de propriétaire  
02480  
 

Philips Bluetooth Headset SBT75 37 User Manual
Philips Car Stereo System MCM169 User Manual
Philips Cassette Player AQ 4150 User Manual
Philips CRT Television 14CE1201 User Manual
Philips Power Supply LR6PB4C User Manual
Pioneer CD Player DEH 2330R User Manual
Pitney Bowes Postal Equipment E500 User Manual
PMC Sierra Network Card PM5347 User Manual
Poulan Lawn Mower 160464 User Manual
PYLE Audio CD Player PLCDCS300 User Manual