R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
810 EP
WARNING:
Read and follow all Safety Rules and Operating Instructions be-
fore using this product. Read instructions carefully before assem-
bling. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. Antes de ensamblar el producto lea
cuidadosamente el instructivo. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Bien lire les
instructions avant d’assembler l’outil. Tout défaut de le faire pour-
rait entraîner des blessures graves.
Poulan
1030 Stevens Creek Road
Augusta, GA 30907
Poulan
5855 Terry Fox Way
Mississauga, Ontario L5V 3E4
545117550
8/8/06
hands. Avoid dangerous situations. Do not
use in the presence of flammable liquids or
gases to avoid creating a fire or explosion
and/or causing damage to unit. Do not abuse
cord. Never carry the unit by the extension
cord or yank extension cord to disconnect
unit. To unplug, grasp the plug, not the cord.
Do not use cord as a handle, close a door on
cord, or pull cord around sharp edges or cor-
ners. Turn off all controls before unplugging.
Do not expose cords to heat, oil, or water. Do
not use with damaged cord or plug. If unit is
not working as it should, has been dropped,
damaged, left outdoors, or dropped into wa-
ter, return it to your authorized service dealer
for repair. Unplug the unit from the power
source when not in use, before servicing, and
when changing accessories and/or attach-
ments. Do not put any object into openings.
Do not use with any opening blocked; keep
freeof dust, lint, hair and anything that may re-
duce air flow.
Safety Hat
Hearing
Protectio
e
tection
Snug
Fitting
Clothing
Heavy Duty
Gloves
Safety
Shoes
Chaps
S Keep all parts of your body away from the
chain when unit is running.
S Keep children, bystanders, and animals a
minimum of 50 feet (15 meters) away from
the work area. Do not allow other people or
animals to be near when starting or operat-
ing the unit. Do not let visitors contact unit or
extension cord.
S Use a voltage supply as shown on unit.
S Avoid dangerous environments. Do not use
in unventilated areas or where dust or ex-
plosive vapors can build up.
HA
S To reduce the risk of electrical shock, this
equipment has a polarized plug (one blade
is wider than the other) and will require the
use of a polarized extension cord. The ap-
pliance plug will fit into a polarized exten-
sion cord only one way. If the plug does not
fit fully into the extension cord, reverse the
plug. If the plug still does not fit, obtain a
correct polarized extension cord. A polar-
ized extension cord will require the use of a
polarized wall outlet. This plug will fit intothe
polarized wall outlet only one way. If plug
does not fit fully into the wall outlet, reverse
the plug. If it still does not fit, contact a quali-
fied electrician to install the proper wall out-
let. Do not change the equipment plug, ex-
tension cord receptacle, or extension cord
plug in any way.
50 feet
(15 meters)
DANGER: Do not
use near electrical
wires or power lines.
Keep pruner at least
30 feet (10 meters)
away from all power
lines.
S Do not handle or operate this unit when you
are fatigued, ill, or upset, or if you have taken
alcohol, drugs, or medication. You must be in
good physical condition and mentally alert. If
you have any condition that might be aggra-
vated by strenuous work, check with doctor
before operating this unit.
S Carefully plan your operation in advance.
Do not start cutting until you have a clear
work area, secure footing, and a planned
retreat path. Cluttered areas invite injuries.
If situations occur which are not covered in
this manual, use care and good judgment. If
you needassistance, contact your authorized
service dealer or call 1-800-554-6723.
S To reduce risk of electrical shock, use exten-
sion cords specifically marked as suitable for
outdoor appliances having electrical rating not
less than the rating of unit. Cord must be
marked with suffix “W--A” (in Canada “W”).
Make sure your extension cord is in good
condition. Inspect extension cord before use
and replace if damaged. Do not use a dam-
aged cord. Cord insulation must be intact with
no cracks or deterioration. Plug connectors
must be undamaged. The extension cord
used to reach the power source must be
heavy enough to carry current from the power
source the full length of the extension cord to
the unit. An undersized extension cord will
cause a drop in line voltage resulting in loss of
power and overheating. If in doubt, use the
next heavier gauge. The lower the gauge
number, the heavier the cord (see SELECT
AN EXTENSION CORD in the OPERATION
section).
ELECTRICAL SAFETY
(applies to all attachments)
WARNING:
Avoid a dangerous environment. To reduce
the risk of electrical shock, do not use in rain,
in damp or wet locations, or around swimming
pools, hot tubs, etc. Do not expose to snow,
rain, or water to avoid the possibility of electri-
cal shock. Do not use on wet surfaces. Do not
handle extension cord plug or unit with wet
S Do not use multiple cords.
S Keep the extension cord clear of operator
and obstacles at all times. Position cord so
that it will not be caught on branches.
3
S Tie cord to cord retainer and connect to re-
cessed plug as shownin this manual to pre-
vent damage to unit and/or extension cord
and to reduce the possibility of the exten-
sioncorddisconnecting fromthe unit during
operation. SeeATTACH THE EXTENSION
CORD TO YOUR TRIMMER in the OP-
ERATION section.
S Do not attempt to repair unit. Inspect the insu-
lation and connectors on the powerhead and
extension cord before each use. If there is
any damage, do not use until damage is re-
paired by your authorized service dealer.
S Do not use the unit if the switch does not
turn the unit on and off properly. Repairs to
the switch must be made by your autho-
rized service dealer.
S Avoid unintentional starting of the unit. Nev-
er carry unit with your finger on the switch.
Be sure the switch is in the OFF position
and never touch the switch when connect-
ing extension cord.
S Avoid any body contact with any grounded
conductor, such as metal fences, or pipes,
to avoid the possibility of electric shock.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on circuit or
outlet to be used. Receptacles are avail-
able having built-in GFCI protection and
may be used for this measure of safety.
S Stop the motor immediately if you are ap-
proached.
DOUBLE INSULATION CONSTRUCTION
This unit is double insulated to help protect
against electric shock. Double insulation
constructionconsists of two separate“layers”
of electrical insulation instead of ground-
ing.Tools built with this insulation system are
not intended to be grounded. No grounding
means is provided on this unit, nor should a
means of grounding be addedto this unit. As a
result, the extension cord used with your unit
can be plugged into any standard 120 volt
electrical outlet. Safety precautions must be
observed when operating any electrical tool.
The double insulation system only provides
added protection against injury resulting from
an internal electrical insulation failure.
sult from one-handed operation. A pruner is
intended for two-handed use.
S Do not operate pruner from a ladder or in a
tree.
S Do not use apruner tocut downtrees or any
portion of the tree trunk.
S Only use for pruning limbs or branches
overhead not greater than 4 inches (10 cm)
in diameter.
S Never standunder the limb you are pruning.
Always position yourself out of the path of
falling debris.
S Do not cut smallbrush andsaplings withthe
pruner. Slender matter may catch in the
chain and be whipped toward you, pulling
you off balance.
S Make sure the chain will not make contact
with any object while starting the unit. Never
try to start the unit when the guide bar is in a
cut.
S Do not force pruner. It will do the job better and
safer at the rate for which it was intended.
S Do not put pressure onthe pruner at the end
of the cut. Applyingpressurecan cause you
to lose control when the cut is completed.
S Do not run the unit at high speed when not
pruning.
S Use the right tool, cut wood only. Don’t use
pruner for purpose not intended; for example,
don’t use pruner for cutting plastic, masonry,
non-wood building materials, etc.
S If you strike or become entangled with afor-
eign object, stop the unit immediately and
check for damage. Have any damage re-
paired by an authorized service dealer be-
fore attempting further operations.
S Do not operate a pruner that is damaged,
improperly adjusted, or not completely and
securely assembled. Always replace bar
and chain immediately if it becomes dam-
aged, broken or is otherwise removed.
S Always stop the unit when work is delayed
or when walking from one cutting locationto
another. Stop the motor and make sure
chain has stopped moving before setting
the unit down.
S Inspect cords periodically and if damaged,
have repaired by an authorized service
dealer.
S Use only in daylight or good artificial light.
WARNING:
KICKBACK
All electrical repairs to this unit, including
housing, switch, motor, etc., must be diag-
nosed and repaired by qualified service per-
sonnel. Replacement parts for a double insu-
lated appliance must berecommended by the
manufacturer. A double insulated applianceis
marked with the words “double insulation” or
“double insulated”. The symbol (square with-
WARNING: Avoid kickback which
can result in serious injury. Kickback is the
backward, upward or sudden forward motion
of the guide bar occurring when the chain
near the upper tip of the guide bar contacts
any object such as a log or branch, or when
the wood closes in and pinches the chain in
the cut. Contacting a foreign object in the
wood can also result in loss of control.
S Rotational Kickback can occur when the
moving chain contacts an object at the upper
tip of the guide bar. This contact can cause
the chain to dig into the object, which stops
the chain for an instant. The result is a light-
ning fast, reverse reaction which kicks the
guide bar up and back toward the operator.
in a square)
may also be marked on the
appliance. Failure to have theunit repairedby
qualified service personnel can cause the
double insulation construction to become in-
effective and result in serious injury.
OPERATE YOUR PRUNER SAFELY
S Do not operate a pruner with one hand. Seri-
ous injury to the operator, helpers, bystanders
or any combination of these persons may re-
4
S Pinch-Kickback can occur when the wood
closes in and pinches the moving chain in
the cut alongthetop of the guidebar and the
chain is suddenly stopped. This sudden
stopping of the chain results in a reversal of
the chain force used to cut wood and
causes the pruner to move in the opposite
direction of the chain rotation. The pruner is
driven straight back toward the operator.
S Pull-In can occur when the moving chain
contacts a foreign object in the wood in the cut
along the bottom of the guide bar and the
chain is suddenly stopped. This sudden stop-
ping pulls the pruner forward and away from
the operator and could easily cause the oper-
ator to lose control of the pruner.
S Keep a good, firm grip on the pruner with both
hands when the unit is running and don’t let
go. A firm grip will help you reduce kickback
and maintain control. Keep the fingers of your
left hand encircling and your left thumb under
the assist handle. Keep your right hand com-
pletely around the trigger handle whether your
are right handed or left handed.
S Stand with your weight evenly balanced on
both feet.
S Stand slightly to the left side of the pruner to
keep your body from being in a direct line with
the cutting chain.
KICKBACK SAFETY FEATURES
WARNING: The following features
are included on your pruner to help reducethe
hazard of kickback; however, such features
will not totally eliminate this danger. As a
pruner user, do not rely only on safety de-
vices. You must follow all safety precautions,
instructions, and maintenance in this manual
to help avoid kickback and other forces which
can result in serious injury.
S Reduced--Kickback Guide Bar, designed with
a small radius tip which reduces the size of
the kickback danger zone on the bar tip.
Reduced Kickback Symmetrical Guide Bar
REDUCE THE CHANCE OF
KICKBACK
S Recognize that kickback can happen. With
a basic understanding of kickback, you can
reduce the element of surprise which con-
tributes to accidents.
S Never let the moving chain contact any ob-
ject at the tip of the guide bar.
S Keep the working area free from obstructions
such as other trees, branches, rocks, stumps,
etc. Eliminate or avoid any obstruction that
your chain could hit while you are cutting.
When cutting a branch, do not let the guide
bar contact branch or other objects around it.
S Keep your chain sharp and properly ten-
sioned. A loose or dull chain can increase
the chance of kickback occurring. Follow
manufacturer’s chain sharpening and
maintenanceinstructions. Check tension at
regular intervals, but never with the motor
running. Make sure the bar clamp nut is se-
curely tightened after tensioning the chain.
S Begin and continue cutting at full speed. If
the chainis moving at aslower speed, there
is greater chance of kickback occurring.
S Cut one branch at a time.
Small Radius Tip
Symm
Lrge Radius Tip
S Low--Kickback Chain, designed with a con-
toured depth gauge and guard link which de-
flect kickback force and allow wood to gradu-
ally ride into the cutter. A low kickback chain
has met kickback performance requirements
when tested on the representative sample of
the chain saws specified in ANSI B175.1.
Contoured Depth Gauge
S Use extreme caution when re-entering a
previous cut.
S Do not attempt cuts starting with the tip of
the bar (plunge cuts).
S Watch for shifting of wood or other forces that
could close a cut and pinch or fall into chain.
S Use the Reduced--Kickback Guide Bar and
Low--Kickback Chain specified for your unit.
Elongated Guard Link
Deflects
kickback force
and allows wood
MAINTAIN CONTROL
Low---Kickback
to gradually ride
Chain
into cutter
Can Obstruct Material
Not a Low---Kickback Chain
MAINTAIN YOUR UNIT IN GOOD
WORKING ORDER
S Have all service performed by a qualified
service dealer with the exception of the
items listed in the maintenance section of
this manual.
S Maintain unit according to recommended
procedures.
S Make certain the chain stops moving when
trigger switch is released.
S Never modify your unit in any way.
5
S Keep the handles dry, clean, and free from
oil and grease.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
S Keep oil cap, screws, and fasteners se-
curely tightened.
WARNING: For each optional attach-
ment used, read entire instruction manual be-
fore use and follow all warnings and instruc-
tions in manual and on attachment.
NOTE: Use the assist handle included with
your unit (as shown below) when operating
the following attachments.
S Maintain unit with care.
S Keep chain sharp and clean for better and
safer performance.
S Follow instructions for lubricating and chang-
ing accessories.
S Check for damaged parts. Before further use
of the unit, a part that is damaged should be
carefully checked to determine that it will op-
erate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. Any part that is damaged
should be properly repaired or replaced by an
authorized service dealer unless otherwise
indicated elsewhere in the instruction manual.
S Use only recommended attachments and re-
placement parts to avoid creating a hazard
and/or voiding warranty.
Assist Handle
BLOWER SAFETY
WARNING: Never put hands or other
objects into blower housing to avoid serious
injury from rotating impeller.
WARNING: Inspect area before us-
ing the unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Inspect unit before each use for worn,
loose, missing or damaged parts. Do not
use until unit is in proper working order.
S Do not set unit on any surface except a clean,
hard area. Debris such as gravel, sand, dust,
grass, etc., could be picked up by the air in-
take and thrown out through discharge open-
ing, damaging unit, property, or causing seri-
ous injury to bystanders or operator.
S Never place objects inside the blower tubes
or blower outlet. Always direct the blowing
debris away from people, animals, glass,
and solid objects such as trees, automo-
biles, walls, etc. The force of air can cause
rocks, dirt, or sticks to be thrown or to rico-
chet which can hurt people or animals,
break glass, or cause other damage.
S Check air intake opening and blower tubes
frequently, always with unit stopped and
power source disconnected. Keep vents
and discharge tubes free of debris which
can accumulate and restrict proper air flow.
S Never place any object inair intake opening
as this could restrict proper air flow and
cause damage to the unit.
S When not in use, the unit should be stored in a
dry, high or locked-up place out of the reach of
children.
S When storing unit, unplug and use a bar
sheath.
TRANSPORTING AND STORAGE
S Stop the unit and disconnect the power
source when not in use.
S Carry the unit with motor stopped.
S Store unit indoors in a high, dry place out of
the reach of children. Store unit unplugged.
S Do not hang unit so that the trigger switch is
depressed.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of hand tools could
cause blood vessel or nerve damage in the
fingers, hands, and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, or joints, discontinue the use
of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who op-
erate power tools on a continual and regular
basis must monitor closely their physicalcon-
dition and the condition of this tool.
S Never douse or squirt the unit with water or
any other liquid. Clean unit and labels with a
damp sponge. Keep handles dry, clean,
and free from oil and grease.
S Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
S To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
RECOMMENDED ATTACHMENTS
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . PP1000E
Cultivator . . . . . . . . . . . . . . . . . PP2000T
Blower . . . . . . . . . . . . . . . . . . . PP3000B
CULTIVATOR SAFETY
WARNING: Use of any other attach-
ments besides those listed above and the at-
tachment provided with this unit might present a
risk of injury to the operator or bystanders. Only
those attachments listed above and the attach-
ment provided with this unit have been tested for
use with this powerhead.
DANGER: RISK OF CUT. KEEP
HANDS AND FEET AWAY FROM TINES AND
CUTTING AREA. Rotating tines can cause se-
rious injury. Do not attempt to clear away cut
material or hold material to be cut when the mo-
tor is running. Make sure powerhead is stopped
6
and disconnected from power source when re-
moving jammed material from the tines. Do not
grab or hold attachment by the tines.
WARNING: Rotating tines can cause
serious injury. Keep away from rotating tines.
Stop the unit and disconnect the power source
before unclogging tines or making repairs.
Handlebar
DANGER: RISK OF CUT. KEEP
HANDS AND FEET AWAY FROM BLADE
AND CUTTING AREA. Do not attempt to clear
away cut material when the blade is in motion.
Make sure powerhead is stopped anddiscon-
nected from power source when removing
jammed material from the cutting blade. Do not
grab or hold unit by the cutting blade.
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
WARNING: Inspect the area to be
cultivated before starting the unit. Removeall
debris and hard and sharp objects such as
rocks, vines, branches, rope, string, etc.
S Hold the unit firmly with both hands
S Keep firm footing and balance. Do not over-
reach or stand on unstable surfaces.
S Look behind and use care when backing up.
S Keep all parts of your body away from the
tines.
S Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others.
S Allow blade to stop before removing it from
the cut.
S Never operate the cultivator without the tine
guard in place and properly secured.
S Keep the tines and guard clear of debris. Al-
ways wear gloves when servicing or clean-
ing the tines. The tines become very sharp
from use.
S Avoid heavy contact with solid objects that
might stop the tines. If heavy contact oc-
curs, stop the motor and inspect the unit for
damage.
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not over-
reach or stand on unstable surfaces.
S Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
S Keep all parts of your body away from the
blade.
S After striking a foreign object, stop the unit,
disconnect the power source and inspect
the cultivator for damage. Repair before re-
starting.
S Disconnect attachment from the drive mo-
tor beforecleaningthetines with a hose and
water to remove any build--up. Oil the tines
to prevent rust.
S Keep blade guard in place and in good
working order.
S Do not run unit at high speed unless culti-
vating.
S Always keep the wheel in contact with the
ground.
EDGER SAFETY
S Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
S To reduce the risk of fire, do not allow exces-
sive grass, leaves, or grease to accumulate
on the attachment.
S Objects struck by the cutting member can
cause serious injuries to persons. The lawn
should always be carefully examined and
cleared of all objects prior to edging.
WARNING: Always use handlebar
when operating edger attachment. Attach
handlebar above arrow on safety label on the
upper shaft (motor end of unit). If your edger
attachment does not include a handlebar, a
handlebar accessory kit (#530071864) is
available from your authorized service dealer.
Instructions for assembling handlebar to your
unit are included in this kit.
SAVE THESE INSTRUCTIONS
7
S When using the trimmer attachment, keep
cutting line at proper length. Use only 0.080″
(2 mm) diameter Poulan brand line. Never
use wire, rope, string, etc.
WARNING: Use of any other attach-
ments not recommended in this manual may in-
crease the risk of injury to persons, fire, or elec-
trical shock. Use of attachments not covered
under the list of recommended attachments in
this manual have not been evaluated for use
with this powerhead by Underwriters Laborato-
ries (see RECOMMENDED ATTACHMENTS).
S Install required shield properly before using
the trimmer attachment. Use only specified
trimmer head and spool; make sure it is
properly installed and securely fastened.
S Cut from your right to your left. Cutting on
left side of the shield will throw debris away
from the operator.
S Store the unit so the line limiter blade (on
underside of shield) cannot cause injury.
VACUUM SAFETY
WARNING: This unit is not designed
for use with a brushcutter attachment.
LINE TRIMMER SAFETY
DANGER: Never use blades withline
trimmer attachment. Never use flailing de-
vices with any attachment. Use of any other
accessories with line trimmer attachment will
increase the risk of injury.
WARNING: Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Never place objects inside the vacuum
tube(s). Always direct the blowing debris
away frompeople, animals, glass, and solid
objects such as trees, automobiles, walls,
etc. The forceof air can cause rocks, dirt, or
sticks to be thrown or to ricochet which can
hurt people or animals, break glass, or
cause other damage.
S Never run unit without the proper equip-
ment attached. When using your unit as a
vacuum, always install vacuum tube(s).
S Check air intake opening or vacuum tube(s)
frequently, always with engine stopped and
unit disconnected from power source. Keep
vents and tubes free of debris which can ac-
cumulate and restrict proper air flow.
WARNING: Trimmer line throws ob-
jects violently. You and others can be blinded/in-
jured. Wear eye and leg protection. Keep body
parts clear of rotating line.
Eye Protection
50 ft.
(15 meters)
PRUNER SAFETY
(RECIPROCATING BLADE)
Boots
Keep children, bystanders, and animals 50 feet
(15 meters) away. Stop unit immediately if ap-
proached.
WARNING: The reciprocating blade
can cause severe injury. Inspect the unit be-
fore use. Do not operate unit with a bent,
cracked or dull blade.
WARNING: Inspect the area to be
trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
S Inspect unit before use. Replace damaged
parts. Make sure all handles, guards, and
fasteners are in place and securely fas-
tened. Parts that are damaged must be re-
paired or replaced by an authorized service
dealer. These include head parts that are
cracked, or chipped, guards, and any other
part that is damaged.
WARNING: Keep away from the
blade.The reciprocating blade is sharp. Do not
touch. To prevent serious injury, always stop en-
gine and ensure blade has stopped moving, dis-
connect unit from power source, and wear
gloves when changing or handling the blade.
WARNING: A coasting blade can
cause injury while it continues to move after the
engine is stopped. Maintain proper control of the
unit until the blade has completely stopped mov-
ing. Keep hands, face and feet at a distance
from all moving parts. Do not attempt to touch or
stop the blade when it is moving.
S Keep firm footing and balance. Do not over-
reach or use from unstable surfaces such as
ladders, trees, steep slopes, rooftops, etc.
S Keep all parts of your body away from cut-
ting head and spinning line.
S Keep the cutting head below waist level. Do
not raise handles above your waist. Cutting
head can come dangerously close to your
body.
S Use unit properly. Use only for trimming, edg-
ing, scalping, and mowing. Do not force unit.
It will do the job better and with less risk of in-
jury at the rate for which it was designed.
8
WARNING: For additional information,
refer to the safety section of the instruction
manual supplied with your pruner attachment.
HEDGE TRIMMER SAFETY
WARNING: Never lean over dis-
charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri-
ous injury or blindness.
WARNING: Inspect the area where
the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow -- be
alert for the possibility.
DANGER: RISK OF CUT; KEEP
HANDS AWAY FROM BLADE -- Blade moves
momentarily after the trigger is released. Do not
attempt to clear away cut material when the
blade is in motion. Make sure the unit is discon-
nected from the power source and the blade
has stopped moving before removing jammed
material from the cutting blade. Do not grab or
hold the unit by the cutting blade.
S Direct material discharge away from glass
enclosures, automobiles, etc.
S Do not run motor at high speed while not re-
moving snow.
S Be attentive when using the snowthrower,
and stay alert for holes in the terrain and
other hidden hazards.
Blades move
momentarily
after the
Allow blades to stop
before removing
them from the cut.
S Make sure the rotor will spin freely before at-
taching the snowthrower to the powerhead.
S If the rotor will not rotate freely due to frozen
ice, thaw the unit thoroughly before attempt-
ing to operate under power.
is
d.
S Keep the rotor clear of debris.
WARNING: Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
S Do not use a cutting blade that is bent,
warped, cracked, broken or damaged in any
other way. Have worn or damaged parts re-
placed by your authorized service dealer.
S Always keep unit in front of your body.
Keep all parts of your body away from the
cutting blade.
S Keep the cutting bladeand air vents clear of
debris.
SNOW THROWER SAFETY
S Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
S After striking a foreign object, stop the unit,
disconnect from the power source and in-
spect the snowthrower for damage and re-
pair if necessary before restarting unit.
S Never operate the snowthrower near glass
enclosures, automobiles and trucks.
S Never attempt to use the snowthrower on a
roof.
S Never operate the snowthrower near win-
dow wells, dropoffs, etc.
S Never discharge snow onto public roads or
near moving traffic.
S Clear snow from slopes by going up and
down; never across. Use caution when
changing directions. Never clear snow from
steep slopes.
WARNING: Keep hands and feet
away from the rotor when starting or running
the unit. Never attempt to clear the rotor with
the motor running. Stop the unit and discon-
nect from the power source before unclog-
ging snow or debris from discharge chute or
when adjusting vanes.
S Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
S Look behind and use care when backing
up. Exercise caution to avoidslipping or fal-
ling, especially when operating in reverse.
S Know how to stop quickly.
9
ASSEMBLY
1. Try on shoulder strapand adjust for fit and
balance before starting the unit or begin-
ning a cutting operation.
WARNING: If received assembled,
review all assembly steps to ensure your unit
is properly assembled and all fasteners are
secure.
2. Insert your right arm andhead throughthe
shoulder strap and allow it to rest on your
left shoulder. Make sure the danger sign
is centered on your back and the hook is
to the right side of your waist.
NOTE: A one-half twist is built in the shoul-
der strap to allow the strap to rest flat on the
shoulder.
3. Adjust the strap, allowing the hook to be
about 3 -- 6 inches (8 -- 15 cm) below the
waist.
4. Fasten the strap hook to the clamp lo-
cated between the trigger handle and the
assist handleand lift the tool to the operat-
ing position.
NOTE: It may be necessary to relocate the
shoulder strap clamp on the shaft for proper
balancing of unit.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
TOOLS REQUIRED
S Hex wrench
S Chain adjustment tool (bar tool)
INSTALLING PRUNER ATTACH-
MENT
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
TO RELOCATE SHOULDER STRAP
CLAMP:
LOOSEN
1. Loosen and remove both clamp screws.
2. Place the upper shoulder strap clamp
over the upper shaft.
3. Position the lower shoulder strap clamp
under the upper shaft and align the upper
and lower clamp screw holes.
TIGHTEN
Knob
2. Remove the shaft cap from the pruner at-
tachment (if present).
houlder
amp
3. Position locking/release button of attach-
ment into guide recess of coupler.
4. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
POWERHEAD
END
5. Before using the unit, tighten the knob se-
curely by turning clockwise.
Coupler
Primary Hole
Guide Recess
ATTACHMENT
Lower Shoulder
END
Screws
Strap Clamp
4. Insert two screws into the screw holes.
5. Secure shoulder strap clamp by tighten-
ing screws with a hex wrench.
ADJUSTING THE ASSIST HANDLE
Locking/
Release
Button
Upper
Shaft
Lower
Attachment
WARNING: When adjusting the assist
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. Allattachments aredesigned
to be used in the primary hole.
handle during pruner use, be sure it remains be-
tween the coupler and the
lower arrow
(closest to coupler) on the safety label to ensure
proper balancing of unit. When adjusting the
assist handle during use of optional attach-
ments (or handlebar for edger attachment), it
must be repositioned between the trigger switch
For optional attachments, see the AS-
SEMBLY section of the applicable attach-
ment instruction manual.
SHOULDER STRAP ASSEMBLY
and the
upper arrow (closest to motor) on
the safety label.
WARNING: Proper shoulder strap
adjustments must be made with the motor
completely stopped before using unit.
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an up-
right position; retighten wing nut.
10
OPERATION
KNOW YOUR PRUNER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
ndle
Shoulder Strap Clamp
Motor Housing
Attachment Hanger
Chain
Recessed
Plug
Bar oil fill cap
Cord Retainer
Bar
Bar nut
Trigger Switch
RECESSED PLUG
COUPLER
The RECESSED PLUG is where you attach
your extension cord to the unit.
The COUPLER enables optional attach-
ments to be installed on the unit.
CHAIN TENSION
TRIGGER SWITCH
TheTRIGGER SWITCHis used toturn onthe
unit. Squeeze the trigger switchto operate the
unit. Release to stop.
It is normal for a new chain to stretch during
first 15 minutes of operation. You should
check your chain tension frequently. See
CHAIN TENSION in the SERVICE AND AD-
JUSTMENTS section.
OPERATING INSTRUCTIONS
Use only a voltage supply as specified on
your unit.
SELECT AN EXTENSION CORD
Cord Retainer
Extension Cord Gauge Chart
Length of Cord
Gauge
18 Gauge
16 Gauge
14 Gauge
25 Ft. (7.5 m)
50 Ft. (15 m)
100 Ft. (30 m)
Extension cords are available for this unit.
ATTACH THE EXTENSION
CORD TO YOUR PRUNER
Makea loop in your extensioncord andattach
the cord as shown. Ensure the plug and cord
are firmly and fully engaged.
Extension Cord
Recessed Plug on Unit
BEFORE STARTING PRUNER
Be sure to read the electrical safety informa-
tion in the safety rules section of this manual
before you begin. If you do not understandthe
electrical safety information do not attempt to
use your unit. Seek help from someone that
does understand the information or call the
customer
assistance
help
line
at
1-800-554-6723.
GUIDE BAR AND CHAIN OIL
The bar and chain require lubrication. The
chain oiler provides continuous lubrication to
thechainand guidebar. Lack of oil will quickly
ruin the bar and chain. Too little oil will cause
11
overheating shown by smoke coming from
the chain and/or discoloration of the bar. The
oil output is automatically metered during op-
eration. Always fill the bar oil tank before and
during use as needed (capacity = 4.6 fl. oz.).
Genuine Poulan bar and chain oil is recom-
mended to protect your unit against exces-
sive wear from heat and friction. Poulan oil
resists high temperature thinning.
Coupler
Primary Hole
Guide Recess
Locking/
Release
Button
Upper
Shaft
Attachment
If Poulan bar and chain oil is not available,
use a good grade SAE 30 oil.
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit.
S Never use waste oil for bar and chain lubri-
cation.
S Always stop the unit before removing the oil
cap.
INSTALLING ATTACHMENT
HANGER
WARNING: Always stop unit anddis-
connect from power source before removing
or installing attachments.
An attachment hanger is provided for storage
when attachment is not in use.
To install hanger on attachment:
REMOVING PRUNER ATTACHMENT
1. Remove the shaft cap from the attach-
ment (if present) and discard.
(OR OTHER OPTIONAL ATTACH-
MENTS)
2. Press and hold the locking/release button.
3. Push hanger onto the attachment until the
locking/release button snaps into the hole.
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
OPERATING POSITION
ALWAYS WEAR:
1. Loosen the coupler by turning the knob
counterclockwise.
Upper
Head
Shaft
Coupler
Protection
Eye
Protection
LOOSEN
Lower
Attachment
Long Pants
TIGHTEN
Knob
2. Press and hold the locking/release button.
Heavy Shoes
Locking/Release
Button
DANGER: Do not extend arms above
shoulders while pruning. Do not stand be-
neath branch being cut.
Coupler
Lower Attachment
Upper Shaft
WARNING: Always wear head, eye,
hearing, foot and body protection to reduce
the risk of injury when operating this unit.
When operating unit, clip shoulder strap onto
clamp, stand as shown and check for the fol-
lowing:
S Extend your left arm and hold assist handle
with your left hand.
S Hold trigger handlewith your right hand with
finger on trigger switch.
S Keep motor end below waist level.
S Keep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
S Maintain full weight of tool on your left
shoulder.
3. While securely holding the motor housing
and upper shaft, pull the attachment
straight out of the coupler.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the shaft cap from the attach-
ment (if present).
2. Position locking/release button of attach-
ment into guide recess of coupler.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
4. Before using the unit, tighten the knob se-
curely by turning clockwise.
12
Always release the trigger switch as soon as
the cut is completed, allowing the motor to
stop. Keep the cord away from the cutting
area. Position cord so it will not be caught on
branches and the like during cutting.
PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the moving
chain to contact any other branches or ob-
jects at the nose of the guide bar when prun-
ing. Allowing such contact can result in seri-
ous injury.
Second cut
Third cut
Collar
IMPORTANT POINTS
S
Work slowly, keeping both hands firmly
gripped on the pruner. Maintain secure
footing and balance.
First cut
Pruning technique
S
S
Plan cut carefully. Check directionbranch
will fall.
Watch out for springpoles. Springpoles are
small size limbs which can catch the chain
and whip toward you or pull you off balance.
Use extreme caution when cutting small
size limbs or slender material.
1. Make the first cut 6 inches (15 cm) from
the tree trunk on the bottom of the limb.
Use top of guide bar to make this cut. Cut
1/3 through the diameter of the limb.
NOTE: When making the second and third
cuts, rest the foot of the pruner against the
tree limb that is being cut to prevent whipping
of the branch.
S
S
Watch out for branches immediately be-
hind the branch being pruned. If the chain
hits the rear branch, damage to the unit
may occur.
Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the
pruner when the tension in the wood fi-
bers is released.
S
S
Keep a clear work area. Frequently clear
branches out of the way to avoid tripping
over them.
Long branches should be removed in
several pieces.
Foot
PRUNING TECHNIQUE
When ready to cut, squeeze trigger switch
and allow unit to reach full speed. Apply a light
cutting pressure. DO NOT use back and forth
sawing action.
2. Next, move 2 -- 4 inches (5 -- 10 cm) far-
ther out on the limb and make a second
cut all the way through the limb.
3. Then, make a final cut leaving a 1 -- 2 inch
(2.5 -- 5 cm) collar from the trunk of the
tree to avoid damage to the tree.
MAINTENANCE
S Oil tank -- Discontinue use of unit if oil tank
shows signs of damage or leaks.
WARNING: Disconnect unit from
power source before performing maintenance.
INSPECT AND CLEAN UNIT AND
LABELS
CHECK FOR LOOSE
FASTENERS AND PARTS
S
After each use, inspect complete unit for
loose or damaged parts. Clean the unit
and labels using a damp cloth.
S
S
S
Bar clamp nut
Chain
Bar adjusting screw
S
Wipe off unit with a clean dry cloth.
CHECK FOR DAMAGED OR
WORN PARTS
CHECK CHAIN TENSION
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Trigger switch -- Ensure trigger switch func-
tions properly by pressingand releasing the
trigger switch. Make sure motor starts and
stops.
WARNING: Wear protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving. Make
chain adjustments with lower end supported.
Chain tension is very important. Chains stretch
during use. This is especially true during the first
13
few times you use your pruner. Always check
chain tension each time you use your unit.
1. Use the screwdriver end of the chain ad-
justment tool (bar tool) to move chain
around guide bar to ensure kinks do not
exist. The chain should rotate freely.
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A dull chain
makes a sawdust powder and cuts slowly.
See CHAIN SHARPENING in the SERVICE
AND ADJUSTMENTS section.
BAR MAINTENANCE
Chain Adjustment T
If your pruner cuts to one side, has to be
forced through the cut, or been run with anim-
proper amount of bar lubrication it may be
necessary to service your bar. A worn bar will
damage your chain and make cutting difficult.
After each use, with unit disconnected from
power source, clean all sawdust from the
guide bar and sprocket hole.
ide
Bar
2. Loosen bar clamp nut until it is finger tight
against the bar clamp.
To maintain guide bar:
S Disconnect pruner from power source.
S Loosen and remove bar clamp nut and
chain brake. Remove bar and chain from
pruner.
S Clean the oil holes and bar groove after
each 5 hours of operation.
Adjusting Screw
Bar clamp nut
3. Turn adjusting screw clockwise until
chain solidly contacts bottom of guide bar
rail. Then, turn adjusting screw an addi-
tional 1/4 turn.
Remove Sawdust From
Guide Bar Groove
Adjusting Screw -- 1/4 Turn
Oil Holes
4. Using bar tool, roll chain around guide bar to
ensure all links are in bar groove.
S Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
5. Lift up tip of guide bar to check for sag.
Release tip of guide bar, then turn adjust-
ing screw 1/4 turn clockwise. Repeat until
sag does not exist.
S When rail top is uneven, use a flat file to re-
store square edges and sides.
6. While lifting tip of guide bar, tighten bar
clamp nut securely with the bar tool.
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
Replace guide bar when the groove is worn,
the guide bar is bent or cracked, or when
excess heating or burring of the rails occurs. If
replacement is necessary, use only the guide
bar specified for your pruner in the repair
parts list.
7. Use the screwdriver end of the bar tool to
move chain around guide bar.
8. If chain does not rotate, it is too tight. Slightly
loosen bar clamp nut and loosen chain by
turning the adjusting screw 1/4 turn counter-
clockwise. Retighten bar clamp nut.
LUBRICATION
Bar Oil
Fill Cap
9. If chain is too loose, it will sag below the
guide bar and needs to be tightened fol-
lowing above procedure.
WARNING: DO NOT operate the
pruner if the chain is loose. If the pruner is oper-
ated with a loose chain, the chain could jump off
the guide bar and result in serious injury.
S See GUIDE BAR AND CHAIN OIL under
the OPERATION section.
14
SERVICE AND ADJUSTMENTS
Depth Gauge
Cutters
WARNING: Disconnect unit from
power source before performing service or
making adjustments.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires special tools. We recommended you
refer chainsharpening to a professionalchain
sharpener.
Drive Links
CHAIN REPLACEMENT
WARNING: Wear protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving.
It is normal for a new chain to stretch during the
first 15 minutes of operation. You should re-
check your chain tension frequently and adjust
the chain tension as required. See CHAIN TEN-
SION section.
Replace the old chain when it becomes worn or
damaged. Use only the Low-Kickback replace-
ment chain specified in the repair parts list.
8. Place chainover sprocket, fitting the drive
links in the sprocket.
9. Fit bottom of drive links between the teeth in
the sprocket in the nose of the guide bar.
10. Fit chain drive links into bar groove.
11. Pull guide bar forward until chain is snug
in guide bar groove. Ensure all drive links
are in the bar groove.
TO REPLACE CHAIN:
1. Disconnect pruner from power source.
2. Remove bar clamp nut.
3. Remove bar clamp.
4. Turn adjusting screw by hand counter-
clockwise until adjusting pin just touches
the stop.
12. Now, install bar clamp making sure the
adjusting pin is positioned in the lower
hole in the guide bar.
5. Slide guide bar behind sprocket until
guide bar stops against sprocket.
6. Remove the old chain.
7. Carefully remove new chain from pack-
age. Hold chain with the drive links as
shown.
Lower
Hole
Adjusting Pin
Cutter
Tip of
Bar
Drivelink
Guide Bar
13. Install bar clamp nut and finger tighten
only. Do not tighten any further at this
point. Proceed to the CHAIN ADJUST-
MENT section.
CHAIN ADJUSTMENT
See CHECK CHAIN TENSION in MAINTE-
NANCE section.
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
USER REPLACEABLE SERVICE PARTS
REPLACEMENT PART
PART NUMBER
Assist Handle
Bolt Carriage, 1/4-20
Wing Nut
Bar
Chain
Hex Nut
Oil Cap
Bar Adjusting Screw/Pin Kit
Handlebar Accessory Kit
530057546
530015786
530016152
530044908
952051549
530015917
530053072
530069110
530071864
15
STORAGE
SEASONAL STORAGE
WARNING: Perform the following
steps after each use.
Prepare your unit for storage at the end of the
season or if it will not be used for 30 days or
more.
S Stop the unit and disconnect the power
source when not in use.
If your unit is to be stored for a period of time:
S Clean it thoroughly before lengthy storage.
S Store in a clean dry area.
S Carry the unit with motor stopped.
S Allow motor to cool before storing or trans-
porting.
S Lightly oil external metal surfaces and guide
bar.
S Store unit and extension cord indoors in a
high, dry place out of the reach of children.
Store unit unplugged.
S Oil the chain and wrap it in heavy paper or
cloth.
S Store pruner with all guards in place and posi-
tion pruner so that any sharp object cannot
accidentally cause injury.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before per-
forming all of the recommendedremedies below except remedies that requireunit tobe
operating.
TROUBLE
CAUSE
REMEDY
1. Chain tension incorrect.
1. See “Check Chain Tension” in
Chain does
not move
when trigger
switch is
Maintenance section.
2. Guide bar rails pinched.
3. Trigger switch failure.
2. Repair or replace.
3. Contact an authorized service
dealer.
engaged.
4. Circuit breaker tripped/
fuse failure.
4. Reset circuit breaker or replace fuse.
Chain clatters
or cuts
roughly.
1. Chain tension incorrect.
1. See “Check Chain Tension” in
Maintenance Section.
2. Cutters damaged.
2. Contact an authorized service
dealer.
3. Chain worn.
3. Resharpen or replace chain.
4. See “Chain Sharpening” in
Service and Adjustments section.
4. Cutters dull, improperly
sharpened, or depth
gauges too high.
5. Sprocket worn.
5. Contact an authorized service
dealer.
Chain stops
during cut.
1. Chain cutter tops not
filed flat.
2. Guide bar burred or
bent; rails uneven.
1. See “Chain Sharpening” in
Service and Adjustments section.
2. Repair or replace guide bar.
Oil inadequate
for bar and
chain lubrica-
tion.
1. Oil tank empty.
1. Fill oil tank.
2. Oil outlet clogged.
2. Contact an authorized service
dealer.
3. Guide bar oil hole
blocked.
3. Remove bar and clean.
1. Cutters damaged on
one side.
1. See “Chain Sharpening” in
Service and Adjustments section.
2. See “Chain Sharpening” in
Service and Adjustments section.
3. Replace guide bar.
Chain cuts at
an angle.
2. Chain dull on one side.
3. Guide bar bent or worn.
16
LIMITED WARRANTY
Poulan warrants to the original purchaser
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of Poulan is to continuously im-
prove its products. Therefore, Poulan re-
serves the right to change, modify, or discon-
tinue models, designs, specifications, and
accessories of all products at any time with-
out notice or obligation to any purchaser.
that each new Poulan brand electric or cord-
less product is freefrom defects in material and
workmanship and agrees to repair or replace
under this warranty any defective Poulan brand
electric product within two (2) years from the
original date of purchase.
If your Poulan brand electric or cordless
product should fail withinthe limited warranty
period, return it, complete, prepaid, with proof
of purchase, to the dealer from whom it was
purchased for repair or replacement at the op-
tion of Poulan.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or the use of
accessories and/or attachments not specifically
recommended by Poulan for this electric prod-
uct. Additionally, this warranty does not cover
parts that will wear and require replacement with
reasonable use during the warranty period. This
warranty does not cover predelivery set--up or
normal adjustments explained in the instruction
manual.
17
|