Samsung Cell Phone Accessories SNH 1010N User Manual

1. Smart phone requirements  
4. Enter required information and  
touch <Register> to finish  
subscribing for Samsung  
Hardware / Operating System  
Requirements  
- iOS 4.3.5/5.0  
OS  
Smartcam membership.  
CPU  
- 600MHz or higher  
ID : Your ID, use alphanumeric  
characters and “.” (full stop)  
and allows 8-14 characters.  
- 128MB or more (recommended),  
RAM : 50MB (Minimum)  
RAM  
- Wi-Fi or 3G wireless communication-  
enabled smart phone  
User ID check : Checks  
Network  
whether the ID already exists.  
Video Codec  
- H.264  
PW : Password does not  
allow ‘-’ and ‘,’. Use 8-14  
alphanumeric characters.  
SmartCam  
mobile  
Recommended Smart Phones - iPhone 3Gs, 4  
Recommended Tablet PC  
- iPad 2  
Confirm Password : Checks whether your password is  
entered correctly.  
Name : Enter your name.  
for iPhone  
2. Subscription  
E-mail : This e-mail is used to recover your subscription if  
you forgot your password.  
SNH-1010N  
1. Run the downloaded application.  
Country : Enter your country of use.  
Register : Requests registration of your information.  
Download the application from the App Store and install it on  
your smart phone.  
2. Touch <Sign up here>.  
Search keywords for the application: “Samsung SmartCam”,  
Smartcam”, “SAMSUNG TECHWIN”, “TECHWIN”.  
3. Check to agree to the terms  
and conditions, and then touch  
<Next>.  
6. Live Video  
1. Touch the desired cameras  
Live Video  
Two-way Audio  
[
] or touch the <Live> icon.  
g
1. Tap on the Two-way Audio icon.  
2. The Mic icon will appear.  
2. Enter the <Private Key> for  
the camera selected. This is the  
same private key you created  
at the time you registered the  
camera. Check the <SAVE>  
option to save the private key.  
Within 20 seconds, it will start  
streaming.  
a
b
c
d
e
f
3. Press and hold the Mic icon and start talking. Press and  
hold for 2sec after finished talking to properly send the  
audio over the internet.  
4. You do not need to have 2-way Audio enabled to receive  
audio from the camera. The Mic setting in the camera must  
be set to 1 and above to have 2-way audio.  
No.  
Description  
Capture  
You can capture and save a still image from the video.  
Enables high quality video (640x480 resolution).  
a
b
HQ  
Video and audio playback depends on the policies of  
your service provider or the network connection status.  
`
`
When there are multiple users logged on to the camera, first person  
who tap the Talk icon will have the control.  
J
Flip  
Flips the video image.  
c
d
Condition  
Wi-Fi  
Audio Support  
Brightness Adjusts the screen brightness.  
O
Two-way  
Audio  
Enable 2-way audio between the camera and the  
phone.  
3G  
Depending on your network.  
e
f
g
Relay Mode  
X
`
The loading time may be longer depending on the policy of the  
service provider or the network connection status.  
Info  
Mic  
Displays current video and audio information.  
M
Relay mode  
Press and hold to talk. Let go to hear back from the  
camera.  
Depending on your network connection, peer to peer connection  
may not be available. When peer to peer connection is not  
available, the camera will connect in Relay Mode, which limits  
the viewing to 3 minutes initially and will prompt you to extend  
another 60 seconds up to three times.  
`
Relay mode is added feature where the video from the camera is  
transmitted to Samsung server then retransmitted to the user's  
computer.  
J
`
`
Audio is not supported in Relay Mode.  
samsungsmartcam.com", go to support page, and refer to  
“Troubleshooting” on it.  
7. Event List  
1. Tap on the <Event> icon to see  
the YouTube and Picasa event  
links.  
2. Tap on the <Delete All> to clear  
the event list.  
YouTube icon:  
Tap on the YouTube  
icon to play the YouTube  
video.  
Picasa icon:  
Tap on the Picasa icon  
to see picture.  
Audio  
Detection icon  
Motion Detection  
Icon  
Deleting Each Event  
2. The camera must have the  
Youtube and Picasa notification  
enabled to have the events listed  
in the Event list. The event list will  
be created after the event video  
and picture is created on your  
YouTube or Picasa account.  
1. Slide you finger right to left on  
the event you want to delete.  
`
Phone does not allow you to play the private videos automatically.  
To see the event videos on your phone, tap on the YouTube app and  
sign into your account(same YouTube account used for the Camera).  
While logged in to the YouTube, touch the YouTube icon to play the  
video automatically.  
M
Deleting All Events  
1. Tap on the <Edit> then Tap on  
the <Clear>.  
`
You will get a notification prompt  
when event is detected by the  
camera.  
M
2. Tap on <Delete> to delete the  
event.  
8. Camera Setup  
Touch the <Setup> icon to configure a camera to be monitored.  
3. Configure the notification.  
Time setting  
Push Notification : Notifies  
alarm events.  
1. Touch <Time setting>.  
2. Set the cameras clock.  
YouTube : Creates 30 seconds  
long footage and uploads onto  
the users YouTube account.  
Time Zone : Select your region.  
Summer Time : Check this  
option if you live in a country  
or region where DST(Daylight  
Saving Time) is applied.  
Picasa : Sends event images  
to the users Picasa account.  
4. Touch <Apply>.  
Network setting  
9. Auto Login Setup  
1. Touch the <Network setting>.  
General setting  
2. Configure the wireless network.  
1. Move to the <Setup> item.  
1. Touch <General setting>.  
Wi-Fi : Shows the list of  
available access points.  
2. Enable <Auto Login> to login  
automatically from the next  
application running.  
2. Configure the basic camera  
settings.  
-
: Connecting to the AP  
requires password.  
Camera Name : Camera name  
is used to easily identify the  
camera when you have more  
than one. i.e., Living room,  
Kitchen, Bedroom.  
-
: Connecting to the AP  
requires no password.  
Other WiFi Networks : Enter  
the SSID name and password  
to connect to the network.  
Event Alarm : Specify whether  
to trigger the alarm or not, and  
specify the sensitivity.  
If selected, it shows guide on SSID and networking  
procedures.  
The higher the sensitivity is, the  
subtler motion/audio events will be detected.  
10. Info.  
Night Vision : Set the IR lighting.  
Enable <Night Vision> for the camera to switch  
automatically to night vision mode.  
1. Move to the <Info.> item.  
2. Shows the information on  
Samsung Techwin Smartcam  
Application.  
vX.XX  
Audio : Adjust the volume of the built-in microphone and  
speaker of the camera as appropriate.  
XXXX.X.XX.  

Toshiba HDD2189 User Manual
Sony Xperia Tipo 1264 0774 User Manual
Seagate EE25 SERIES ST940814AM User Manual
Seagate CHEETAH ST3450802SS User Manual
Seagate Barracuda ST360019A User Manual
Samsung GT S3100 User Manual
Samsung FLEX MUXONENAND KFN8GH6Q4M User Manual
Samsung Cell Phone GT I9505 User Manual(1)
Philips SPD6000FO User Manual
Philips 170X7 User Manual