Addonics Technologies Computer Accessories CRC4HESU User Manual

ADDONICS TECHNOLOGIES  
Model: CRC4HESU  
IMPORTANT  
There is no back door for the Cipher tower encrypted hard  
drives if the Cipher keys are lost or stolen.  
A switch located on the left hand side of the Ruby Cipher  
enclosure front panel must be placed to the “INT” position. This  
will secure the enclosure and provide power to the drive.  
Cipher key  
Check to make sure you have the  
correct version of the Cipher key. A  
sample key is shown  
Switch  
Black label AES-256 stands for  
Cipher 256-bit key.  
Cipher keyhole  
Power LED and  
Drive Access LED  
To ensure there is a spare key, your Cipher tower comes with  
4 pairs of Cipher keys. These cipher keys have all identical  
encryption code unless you requested then to be coded  
differently. One of these keys should be kept in a safe and  
secure location and can be sent back to Addonics for duplicating  
additional keys. If you are down to the last key, be sure to make  
a back up of all the data stored inside your Cipher tower prior to  
sending the last key to Addonics. Addonics is not responsible for  
key lost in the mail or retrieval of the data inside the encrypted  
hard drive.  
Note: It is recommended to fill up the tower with SATA drives  
from top to bottom. This is to help in identifying which drives  
connect to which ports for easier troubleshooting.  
II. Connecting the power cable and Cipher Tower to the  
computer  
a. Connect the power cord provided from the wall outlet to the  
back of the Cipher Tower.  
Keeping track of the hard drive  
b. A power switch is located on the front of the tower. Make  
sure the power is off on the switch (power LED light should  
be off)  
c. Connect the provided eSATA or USB2.0 cable from the back  
of the Cipher tower to the eSATA or USB2.0 on the  
computer. We recommend connecting the eSATA port for  
best performance if this port is available on your computer.  
If you are using the Cipher tower to encrypt multiple hard drives,  
it is important to label your hard drive if you are taking the drive  
out of the Cipher tower. The hard drive from the Cipher tower  
that is encrypted will look like a brand new drive when attach  
directly to the SATA controller of a computer. There will be no  
partition or any hint to indicate that the drive contains encrypted  
data. When the drive is partitioned, all the encrypted data will be  
lost.  
The same holds true if a hard drive already has data on it is  
installed into the Cipher tower. The computer detects the hard  
drive as a brand new drive or a drive that is unallocated. Once  
you proceed to partition the drive, the data that was on the hard  
drive will be erased and cannot be recovered.  
Power  
Switch  
I. Installing drives into the Cipher Tower  
Refer to Ruby Cipher enclosure hard drive installation guide  
(LED 4)  
HPM  
Health  
(LED 2)  
USB  
Status  
Power  
LED  
RAID  
setting  
button  
Open the front panel of the Cipher  
tower.  
USB port  
eSATA port  
RAID config  
rotary switch  
(LED 3)  
HPM  
Power  
(LED 1)  
eSATA  
Status  
Slide the enclosure into the drive bay.  
 

3M Pet Fence 39600 User Manual
AGFA Digital Camera DC 730i User Manual
Agilent Technologies Washer Dryer 10737L User Manual
Aiphone Intercom System JF 1FD User Manual
Airlink Network Card AP431W User Manual
Altinex Switch SW104 130 User Manual
AMX Stereo Receiver TVM RX03 User Manual
AVerMedia Technologies Network Card M039R User Manual
BC Speakers Speaker 12 PZ 32 User Manual
BC Speakers Speaker DE610 User Manual