Canon Camera Accessories 6310B002 User Manual

Nomenclature  
 
②  
③  
④  
Focus mode switch  
Focusing ring  
Lens mount index  
Contacts  
EF Lenses  
EF40mm f/2.8 STM  
Instructions  
Thank you for purchasing a Canon product.  
EF40mm f/2.8 STM is a compact, lightweight, low-profile high quality standard  
single focal point lens.  
About the AF frame selection  
❶  
❷  
❸  
High accuracy cross (+) detection can be used in the center AF frame and  
horizontal line detection can be used in the frames other than the center AF  
frame for the following cameras.  
“STM” stands for Stepping Motor.  
EOS-1Ds Mark III, EOS-1Ds Mark II, EOS-1Ds, EOS-1D Mark IV,  
EOS-1D Mark III, EOS-1D MaII N, EOS-1D Mark II, EOS-1D, EOS-1V,  
EOS-3  
Safety Precautions  
Do not look at the sun or a bright light source through the lens or  
camera. Doing so could result in loss of vision.  
Conventions used in this instn  
Looking at the sun directly through the lens is especially hazardous.  
Whether it is attached to the camera or not, do not leave the lens under  
the sun without the lens cap attached. This is to prevent the lens from  
concentrating the sun’s rays, which could cause a fire.  
Warning to pror cammalfunction or damage.  
Supptary n using the lens and taking pictures.  
Handling Cautions  
1. MouDetahing the Lens  
e youstruions for details on mounting and detaching the  
lens.  
If the lens is taken from a cold environment into a warm one,  
condensation may develop on the lens surface and internal parts. To  
prevent condensation in this case, first put the lens into an airtight plastic  
bag before taking it from a cold to warm environment. Then take out the lens  
after it has warmed gradually. Do the same when taking the lens from a warm  
environment into a cold one.  
After ing the lens, place the lens with the rear end up to prevent  
e lens surface and contacts from getting scratched.  
he contacts get soiled, scratched, or have fingerprints on them,  
orrosion or faulty connections can result. The camera and lens may not  
operate properly.  
Do not leave the lens in excessive heat such as in a car in direct sunlight.  
High temperatures can cause the lens to malfunction.  
If the contacts get soiled or have fingerprints on them, clean them with a  
soft cloth.  
Cautions during shooting  
This lens uses a stepping motor to drive the focusing lens (the lens that has  
the job of focusing the shot).  
1. Cautions when the power is off  
If you remove the lens, cover it with the dust cap. To attach it properly,  
align the lens mount index and the index of the dust cap, and turn  
❶  
clockwise . To remove it, reverse the order.  
Since the motor does not operate when the camera is off or has been  
turned by the auto power-off function, take note of the following points.  
• The focus cannot be adjusted in manual focus mode.  
2. Cautions when the lens is in sleep mode  
This lens has a sleep mode separate from the camera auto power-off  
function for saving power when the lens has not been operated for a period  
of time.  
2. Setting the Focus Mode  
To shoot in autofocus (AF) mode, set the focus mode switch to AF  
.
To shoot in manual focus (MF) mode, set the focus mode switch to MF, and turn  
the focusing ring to set the focus  
.
When the camera AF mode is ONE SHOT AF, focus manually by pressing  
the shutter button halfway and turning the focusing ring. (Full-time manual  
focus)  
Since the motor does not operate when the lens is in sleep mode, even if  
the camera is turned on, take note of the following points.  
• The focus cannot be adjusted in manual focus mode.  
To recover the lens from sleep mode, press the shutter button halfway.  
To retract the lens if extended, keep the lens attached to the camera, and  
then autofocus at infinity or turn the focusing ring.  
To shoot with this lens attached on an EOS-1D Mark IV, update the EOS-  
1D Mark IV firmware to version 1.1.1 or later. Updating to this firmware will  
optimize exposure accuracy.  
When using an EOS film camera, the action of the focus may slow down if  
the battery is low on power or when the ambient temperature is low.  
When turning the focusing ring suddenly, the focus adjustment may be  
delayed.  
The focus cannot be adjusted in MF mode while the camera is off.  
Do not touch the front rotating parts of the lens while autofocus is active.  
 

Black Decker Iron ICR07X User Manual
Blue Rhino Patio Heater 153100 User Manual
Bogen Car Amplifier HTA 125A User Manual
Broilmaster Grill Accessory DPA103 User Manual
Canon Camera Accessories 4411B002 User Manual
Canon Fax Machine FAX L400 User Manual
Casio Network Card Adaptor User Manual
Cateye Bicycle Accessories CC VL800 User Manual
CDA Freezer FW282 User Manual
CDA Refrigerator FW950 User Manual