Cateye Bicycle Accessories CC CD200N User Manual

• Pay attention to the road or trail! Do not be distracted by the  
computer.  
• Be sure to securely mount the magnet, the sensor, and the  
bracket on your bicycle. Periodically check to insure they are  
mounted securely and the screws have not come loose.  
• Keep batteries out of reach of small children. Dispose of batter-  
ies according to local regulations.  
CAT EYE ASTRALE 8  
CYCLOCOMPUTER CC-CD200N  
E: Owner’s Manual  
®
Warning  
• Avoid unnecessary prolonged exposure to the sun.  
• Never attempt to disassemble the computer head.  
• Don’t use thinner, benzene or alcohol to wipe the surface of the  
computer. They may damage the surface of computer.  
Important  
Note  
ASTRALE8  
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending  
Copyright © 2002/2003 CAT EYE Co. Ltd.  
Mount The Bracket  
3 Secure the cord by fastening it to the frame with zip ties at regular intervals.  
CCMCD2N-030531 066600252  
1
Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the  
screw. Slide the computer into the bracket until you hear the click sound. When you need to  
remove the computer, press the lever on the handlebar bracket and slide the computer  
forward.  
Please read these instructions carefully before installing or  
using the CAT EYE ASTRALE 8.  
Please keep this manual in a safe place for future reference.  
Note  
Allow enough wire clearance in the area marked with  
to insure you can turn  
the handlebars all the way from side to side without pulling the wire.  
Installation of the Computer on Your Bike  
The computer comes with the following parts:  
1
Lever  
3
2
3
8
Slide  
1
9
4
1
9
5
2
8
6
Basic Functions Test  
7
4 Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence  
1 Bracket  
2 Cord  
5 Sensor Rubber Pad  
6 Wheel Magnet  
7 Cadence Magnet  
8 Bracket Rubber Pad  
9 Nylon Ties (10)  
(Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly.  
When you receive a signal, tightly secure the sensor so it does not move.  
3 Speed Sensor  
(Long Cord)  
4 Cadence Sensor  
(Short Cord)  
Note  
When the computer does not indicate the speed/cadence, check the position of the  
magnet and the sensor.  
Rotate the crank arm  
Rotate the rear wheel.  
OK  
OK  
1
Mount the wheel magnet and speed sensor  
1 • Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the  
magnet faces the sensor.  
Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9.  
Computer Set-up  
You need to know  
your tire size or the  
roll out length of your  
tire in MM's.  
Note  
The nylon ties can only be used once, please install with care.  
!
(For first use or after replacing the battery)  
9
9
6
Contact Point  
Rear wheel  
spoke  
3
L mm  
The smooth edge of the zip  
tie should be on the outside  
Sensor Side  
Refer to the chart below for  
approximate tire lengths.  
Left chainstay  
Important Note  
L(mm)  
Tire size  
Mount the magnets 6 and the sensors 3 in the appropriate positions so that the  
center of each magnet 6 aligns with the marked sensor line when the rear wheel  
and crank arm are rotated. The magnet should be no more than 5mm from the sensor.  
12 x1.75  
14 x 1.50  
14 x 1.75  
16 x 1.50  
16 x 1.75  
18 x 1.50  
18 x 1.75  
20 x 1.75  
20 x 1-3/8  
22 x 1-3/8  
22 x 1-1/2  
24 x 1  
935  
1020  
1055  
1185  
1195  
1340  
1350  
1515  
1615  
1770  
1785  
1753  
SET Button  
AC Button  
START/STOP Button  
MODE Button  
Left chainstay  
3
Rear wheel spoke  
AC Button  
6
All Clear  
1 Push the AC button on the backside.  
Center  
3
* Push the AC button when using this  
system for the first time and every  
time the battery is replaced.  
24 x 3/4 Tubular 1785  
Adjust  
Marked Line  
6
24 x 1-1/8  
24 x 1-1/4  
24 x 1.75  
24 x 2.00  
24 x 2.125  
26 x 7/8  
1795  
1905  
1890  
1925  
1965  
1920  
1913  
1952  
1953  
1970  
2068  
2100  
2005  
2010  
2023  
2050  
2055  
2068  
2070  
2083  
2170  
2155  
2161  
2161  
2169  
2090  
2125  
2105  
2070  
2080  
2086  
2096  
2105  
2136  
2170  
2155  
2130  
2168  
2180  
2200  
Within 5 mm  
Measurement Selection  
2 Select the measurement unit, kilometer or mile, by pushing the  
MODE button. Fix it by pushing the SET button.  
Mount the cadence magnet and cadence sensor.  
• Mount the cadence magnet 7 on the left crank arm so that it faces the sensor.  
• Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9.  
26 x 1(59)  
26 x 1(65)  
26 x 1.25  
26 x 1-1/8  
26 x 1-3/8  
26 x 1-1/2  
26 x 1.40  
26 x 1.50  
26 x 1.75  
26 x 1.95  
26 x 2.00  
26 x 2.10  
26 x 2.125  
26 x 2.35  
26 x 3.00  
27 x 1  
27 x 1-1/8  
27 x 1-1/4  
27 x 1-3/8  
650 x 35A  
650 x 38A  
650 x 38B  
700 x 18C  
700 x 19C  
700 x 20C  
700 x 23C  
700 x 25C  
700 x 28C  
700 x 30C  
700 x 32C  
700C Tubular  
700 x 35C  
700 x 38C  
700 x 40C  
2
Kilometer  
Mile  
MODE  
9
SET  
9
Inward Side of  
Sensor Side  
7
The Crank Arm  
3
Left Chain Stay  
Set The Tire Circumference  
Set the tire circumference in mm.  
Refer to the chart shown on the right.  
Setting is fixed and completed by pushing the SET button.  
3
Important Note  
Note  
When the crank is spinning, the center of the magnet 7 should pass in front of the sensor  
4 marking line. The distance between the sensor and the magnet 7 should be within  
5mm. After adjusting the magnet and sensor, secure tightly with nylon ties.  
Increase the  
number  
Max. 2999 mm  
Left Chain Stay  
MODE  
4
SET  
Decrease  
the number  
Min. 10 mm  
7
Marked Line  
START/STOP  
Crank Arm  
4
Center  
Preparation Complete.  
7
(the screen will show the time measurement in this state)  
Adjust  
Within 5 mm  
Tire size is usually shown on  
the sidewall of tires.  
* The auto mode is ON in this state.  
 

Black Decker Coffee Grinder CBM205 User Manual
Blue Rhino Outdoor Fireplace WAF517A C User Manual
Bogen Stereo Amplifier WV250 User Manual
Britax Car Seat P222000 User Manual
Brother Sewing Machine N5V User Manual
Campbell Hausfeld Air Compressor Attach it to this manual or file it for safekeeping IN626701AV User Manual
Carrier Refrigerator 30GN040 420 User Manual
CDA Clothes Dryer CI920 User Manual
CFM Ventilation Hood 167193 User Manual
Chromalox Boiler PQ402 6 User Manual