Chauvet Automobile Accessories CH 222 User Manual

CH-222  
AbyssJr.  
USER MANUAL  
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A  
(800) 762-1084 (954) 929-1115  
FAX (954) 929-5560  
2005-07-22/17:40  
 
BEFORE YOU BEGIN  
What is included  
1 x AbyssJr. (CH-222)  
Power cord with plug  
EFP5 100w lamp  
Warranty Card & Manual  
Unpacking Instructions  
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that  
all parts are present, and have been received in good condition. Notify the shipper immediately and  
retain packing material for inspection if any parts appear damaged from shipping or the carton itself  
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture  
must be returned to the factory, it is important that the fixture be returned in the original factory box  
and packing.  
Power  
To determine the power requirements for a particular fixture, see the label affixed to the back plate of  
the fixture or refer to the fixtures specifications chart.  
A fixtures listed current rating is its average current draw under normal conditions.  
All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable  
resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%  
switch.  
Before applying power to a fixture, check that the source voltage matches the fixtures requirement.  
All fixtures must be connected to circuits with a suitable Earth Ground.  
Warning!  
Verify that the power requirement on your unit matches the line voltage applied. All  
fixtures must be connected to circuits with a suitable Earth Ground.  
Safety Instructions  
Please read these instructions carefully, which includes important  
information about the installation, usage and maintenance?  
Please keep this User Guide for future consultation. If you  
sell the unit to another user, be sure that they also receive  
this instruction booklet.  
Secure fixture to fastening device using a safety chain.  
Never carry the fixture solely by its head. Use its carrying  
handles.  
Maximum ambient temperature is Ta: 40°. Do not operate  
fixture at temperatures higher than this.  
In the event of serious operating problem, stop using the  
unit immediately. Never try to repair the unit by yourself.  
Repairs carried out by unskilled people can lead to  
damage or malfunction. Please contact the nearest  
authorized technical assistance center. Always use the  
same type spare parts.  
Dont connect the device to a dimmer pack.  
Make sure power cord is never crimped or damaged.  
Never disconnect power cord by pulling or tugging on the  
cord.  
Always make sure that you are connecting to the proper  
voltage and that the line voltage you are connecting to is  
not higher than that stated on decal or rear panel of the  
fixture.  
This product is intended for indoor use only!  
To prevent risk of fire or shock, do not expose fixture to  
rain or moisture. Make sure there are no flammable  
materials close to the unit while operating.  
The unit must be installed in a location with adequate  
ventilation, at least 50cm from adjacent surfaces. Be sure  
that no ventilation slots are blocked.  
Always disconnect from power source before servicing or  
replacing lamp or fuse and be sure to replace with same  
lamp source.  
Avoid direct eye exposure to lamp while it is on.  
Caution!  
There are no user serviceable parts inside the unit. Do not open the housing or  
attempt any repairs yourself. In the unlikely event your unit may require service,  
please contact CHAUVET.  
CH-222 User Manual  
3
2005-07-22/17:40  
 
         
INTRODUCTION  
The Abyss Jr. projects a wave simulation effect on a wall or any flat surface. It is a wonderful scenic  
effect that adds life and color to any venue.  
Features  
water undulation effect (wave effect)  
bright EFP5 100w MR-16 lamp  
fan cooled  
Product Overview  
Hanging  
Bracket  
Lamp access  
Power  
connector  
Figure 1 Product Overview  
CH-222 User Manual  
4
2005-07-22/17:40  
 
     
SETUP  
Lamp  
You will need to install a lamp prior to the initial operation of the fixture. An EFP 100W halogen lamp  
is included.  
Warning!  
When replacing the lamp, please wait 15 minutes after powering down to allow the  
unit to cool down! Always disconnect from main power prior to lamp replacement.  
Do not touch the envelope (glass area) of the bulb with  
Figure 2 CH-222 Lamp installation  
bare hands. If this happens, clean the lamp with alcohol  
and wipe it with a lint free cloth before installation.  
LAMP INSTALLATION  
1) Remove the four screws located on both sides of  
the fixture and remove fixture cover.  
2) If replacing the lamp, remove old lamp first.  
3) Reach in and slide the lamp out of the retaining  
Remove screws on both sides.  
cage.  
4) Detach the lamp from the lamp socket and  
replace.  
5) Replace fixture cover, align the screw holes and  
fasten the screws.  
6) No lamp alignment is necessary for this fixture  
since the lamp is already optimized inside the  
reflector.  
Lamp exposed  
Mounting  
ORIENTATION  
This fixture may be mounted in any position provided there is adequate room for ventilation.  
RIGGING  
Figure 3 - Hanging Clamp  
It is important never to obstruct the fan or vents pathway. Mount the  
fixture using, a suitable Cor Otype clamp. Adjust the angle of the  
fixture by loosening both knobs and tilting the fixture. After finding the  
desired position, retighten both knobs.  
When selecting installation location, take into consideration lamp  
replacement access and routine maintenance.  
Safety cables should always be used.  
Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature  
changes or restricted ventilation.  
Note!  
Clamps sold separately!  
CH-222 User Manual  
5
2005-07-22/17:40  
 
           
OPERATING INSTRUCTIONS  
The Abyss Jr. is a water ripple or undulation simulation effect that requires no additional connections  
or a controller to operate. It is especially functional when used to project on a light colored surface,  
preferably a pastel or white.  
Whether used in a mobile or permanent environment, you may find it useful to control this effect by  
means of a relay system for remote switching or to go with DMX control, use the latest in DMX  
compatible (Dimmer Relay Pack), all available from CHAUVET.  
A relay system will allow you to remotely trigger the AbyssJr. and any other non-dimmable effect  
light from a switch panel. Make sure to use a cable of at least 25 feet to provide ample distance  
between the control panel and the switch pack for most mobile lighting applications.  
If you would prefer to control it directly from your DMX lighting console then we suggest a DMX  
compatible (relay switch-pack). These devices are an extremely affordable solution to operating non-  
DMX lighting effects remotely.  
To learn more about these and other CHAUVET products visit us at www.chauvetlighting.com.  
CH-222 User Manual  
6
2005-07-22/17:40  
 
 
APPENDIX  
General Maintenance  
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage  
and environment are contributing factors in determining frequency. As a general rule, fixtures should  
be cleaned at least twice a month. Dust build up reduces light output performance and can cause  
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off  
fixture before conducting maintenance.  
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust  
collected on external vents and internal components. Clean all glass when the fixture is cold with a  
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply  
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical  
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil  
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or  
becomes dirty, clean the lamps with an alcohol wipe.  
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to  
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:  
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the units  
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean  
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.  
Returns Procedure  
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.  
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products  
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the  
fixture. Be prepared to provide the model number, serial number and a brief description of the cause  
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate  
packaging is the customers responsibility. CHAUVET reserves the right to use its own discretion to  
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe  
method to use.  
Claims  
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be  
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and  
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim  
for items such as missing component/part, damage not related to shipping, and concealed damage,  
must be made within seven (7) days of receiving merchandise.  
CH-222 User Manual  
7
2005-07-22/17:40  
 
       
Appendix  
General Troubleshooting  
Applies to  
Foggers  
& Snow  
Dimmers  
& Chaser  
Symptom  
Solution(s)  
Lights  
Controllers  
Auto shut off  
Check fan thermal switch reset  
Beam is very dim or not Clean optical system or replace lamp  
bright  
Check 220/110v switch for proper setting  
Breaker/Fuse keeps  
blowing  
Check total load placed on device  
Chase is too slow  
Check users manual for speed adjustment  
Device has no power  
Check for power on Mains.  
Check devices fuse. (internal and/or external)  
Fixture is on but there  
is no movement to the  
audio  
Make sure you have the correct audio mode on the control  
switches. If audio provided via ¼jack, make sure a live  
audio signal exists  
Adjust sound sensitivity knob  
Fluid indicator not  
working  
The filter tip on the end of the tube inserted into the fluid  
container must float freely in order to measure correctly,  
check to see if perhaps it is stuck  
Fogger or Snow output  
has dropped  
Clean with distilled water and vinegar  
Replace hose  
Lamps cuts off  
sporadically  
Possible bad lamp or fixture is overheating.  
Lamp may be at end of its life.  
Light will not come on  
after power failure  
Some discharge lamps require a cooling off period before  
the electronics in the fixture can kick start it again, wait 5 to  
10 minutes before powering up  
Motor movements are  
jerky or jumpy  
Possible bad motor driver or sensors  
Check polarity switch on controller  
Moves slow  
No flash  
No fog  
Check 220/110v switch for proper setting  
Re-install bulb, may have shifted in shipping  
Check fluid tank if empty  
Make sure green light is on (for power)  
No light output  
Check slip ring & brushes for contact  
Install bulb  
Call service technician  
Relay will not work  
Check reset switch  
Check cable connections  
Remote does not work  
Make sure connector is firmly connected to device  
Check for damages possibly incurred during shipping  
Unit wobbles when  
rotating  
CH-222 User Manual  
8
2005-07-22/17:40  
 
 
Appendix  
Technical Specifications  
WEIGHT & DIMENSIONS  
Length.............................................................................................................................178 mm (7 in)  
Width..........................................................................................................................159 mm (6.25 in)  
Height .............................................................................................................................102 mm (4 in)  
Weight.........................................................................................................................1.72 Kg (3.8 lbs)  
POWER  
Operating Range.........................................................................................120V 60 Hz or 230V 50 Hz  
European Version ......................................................................................................230V/240V 50Hz  
AC input.......................................................................................................... 3-prong IEC 60320 C14  
LAMPS  
EFP5..........................................................................................................................50 hr, 100W, 12v  
THERMAL  
Maximum ambient temperature......................................................................................... 40° (104° F)  
FUSE  
Main (115V AC)........................................................................................... 20mm Glass 2A Fast Blow  
Main (230V AC)........................................................................................... 20mm Glass 1A Fast Blow  
ORDERING INFORMATION  
AbyssJr................................................................................................................................ CH-222  
Fuse 2A ........................................................................................................................ P170FUSE002  
Fuse 1A ........................................................................................................................ P170FUSE001  
Technical Support  
Address:  
Service Dept.  
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)  
Support (Email):  
Telephone:  
Fax:  
(954) 929-1115 - (Press 4)  
(954) 929-5560 - (Attention: Service)  
Website:  
CH-222 User Manual  
9
2005-07-22/17:40  
 
   

Black Box Computer Hardware RM 415A User Manual
Black Decker Air Compressor 641915 00 User Manual
Braun Electric Shaver 5015 User Manual
Brinkmann Gas Grill 6430 User Manual
Broil King Oven 9956 54 User Manual
Brother Printer DCP J525W User Manual
Canon Webcam 3814B010 User Manual
Casablanca Fan Company Fan Casablanca 19th Century User Manual
Century Car Seat Deluxe Series User Manual
Chevrolet Automobile 2010 Equinox User Manual