Chief Manufacturing Indoor Furnishings XSM Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
XSM  
XTM  
FUSION EXTRA LARGE HEIGHT ADJUST  
FLAT PANEL MOUNTS  
XSM/XTM Series  
 
Installation Instructions  
XSM/XTM Series  
DIMENSIONS  
XSM  
MAX MOUNTING PATTERN IS 46" (1168.4 mm) WITHOUT REVERSING UPRIGHTS  
WITH REVERSING THE UPRIGHTS  
MAX MOUNTING PATTERN IS 48.4" (1229.4 mm)  
0
10.2  
45  
.40  
12.9  
.51  
1.77  
90  
3.54  
105  
4.13  
24.3  
MINIMUM UPRIG HT SPAC ING  
38.4  
1.51  
150  
5.91  
165  
6.50  
24"  
.96  
25.4  
1.00  
73.9  
2.91  
210  
8.27  
225  
8.86  
8.3  
.33  
270  
10.63  
285  
11.22  
51  
2
383.4  
15.10  
44.5  
1.75  
685.8  
27.00  
330  
12.99  
419.6  
16.52  
345  
13.58  
405  
RAILS CAN BE SLID LEFT  
15.94  
OR RIGHT FOR OFFSET  
25.4  
1.00  
465  
18.31  
525  
1232.7  
48.53  
20.67  
585  
23.03  
630  
24.80  
660  
25.98  
MEASUREMENTS IN: [MILLIMETERS]  
INCHES  
XTM  
WITH REVERSING THE UPRIGHTS  
MAX MOUNTING PATTERN IS 49.2" (1249.7 mm)  
10.2  
.40  
12.9  
.51  
0
45  
1.77  
12°  
MINIMUM UPRIG HT SPAC ING  
MAX TILT WILL VARY DEPENDING  
UPON SC REEN SIZE  
90  
3.54  
24"  
24.4  
.96  
25.4  
1.00  
105  
50.8  
2.00  
4.13  
74.1  
2.92  
150  
5.91  
165  
6.50  
210  
8.27  
25.4  
1.00  
8.3  
.33  
225  
8.86  
270  
10.63  
285  
11.22  
44.5  
1.75  
419.6  
16.52  
383.4  
15.10  
685.8  
27.00  
670.8  
26.41  
330  
12.99  
345  
13.58  
RAILS CAN BE SLID LEFT  
OR RIGHT FOR OFFSET  
405  
15.94  
465  
18.31  
525  
20.67  
1232.8  
48.54  
585  
23.03  
630  
24.80  
660  
25.98  
MEASUREMENTS IN: [MILLIMETERS]  
INCHES  
3
 
XSM/XTM Series  
Installation Instructions  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Potloodmerkteken  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
4
 
Installation Instructions  
XSM/XTM Series  
TOOLS REQUIRED FOR INSTALLATION  
#2  
7/32" (5.5mm) Wood Stud  
5/16" (7.9mm) Concrete  
PARTS  
B (1)  
C (1)  
A (1)  
[Included with  
XSM2XXX/XTM2XXX  
(XTM Only)  
J (1) [Used on XSMU/XTMU Models Only]  
Models Only]  
E (1)  
Custom  
XSM2XXX/  
XTM2XXX  
Hardware  
J2 (6)  
M6x25mm  
J1 (6)  
M6x16mm  
G (1)  
F (1)  
J3 (6)  
J4 (6)  
M8x20mm  
M8x30mm  
(XSM Only)  
J6 (6)  
J5 (4)  
M8x50mm  
M10x40mm  
H (4)  
K (1)  
J7 (6)  
M10x50mm  
J8 (6)  
M6  
J9 (6)  
M8  
L (1)  
K1 (4)  
5/16"  
K2 (4)  
5/16"  
J10 (6)  
1.00x.400x.75"  
J11 (6)  
.750x.323x.250"  
K3 (4)  
5/16" x 2-1/2"  
J12 (1)  
M5  
J13 (1)  
M6  
5
 
XSM/XTM Series  
Installation Instructions  
INSTALLATION  
Center of screen  
The XTM and XSM have been designed to be mounted directly  
onto either a wood stud or concrete wall. The XTM has brackets  
which allow the display to be tilted. The XSM has static brackets  
which keep the display in an upright position.  
7-1/2"  
Locate Mounting Site  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT! It is the installers  
responsibility to make certain the structure to which the  
mount is being attached is capable of supporting five times  
the weight of the XTM or XSM and all attached equipment not  
to exceed 250 lbs (113.4 kg).  
Vertical center  
of mount  
NOTE: Proceed to either the Installing to a Wood Stud Wall  
section or the Installing to a Concrete Wall section.  
Installing to a Wood Stud Wall  
CAUTION: MINIMUM HORIZONTAL DISTANCE  
BETWEEN WALL BRACKETS IS 24". Do not place mounting  
brackets closer together than 24". When attaching to a wall  
containing studs located 16" on center, space the uprights  
32" apart.  
Figure 1  
5. Using a level, mark the wall on each stud to attach the  
mount through the upper mounting slots. (See Figure 2)  
1. Determine the center of the display, and where it should be  
located on the wall.  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL CORDS OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surface is free  
of electrical wires and cables before drilling or installing  
fasteners.  
2. Locate the appropriate studs to the left and right of the  
selected location.  
NOTE: If the screen area lies over a stud, use that stud and an  
appropriate stud to either the left or right of it.  
3. Line up the notches on mount with center of screen marking  
to determine vertical center. (See Figure 1)  
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surface is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
4. Measure up 7-1/2" from the center point to mark location of  
the upper mounting slots.  
6. Drill one 7/32" pilot hole in each stud.  
7. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) to attach top of mount to wall. (See Figure 2)  
6
 
Installation Instructions  
XSM/XTM Series  
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surface is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
6
5
8
9
4
5
(K1) x 4  
6 10  
x4  
7
(K3) x 4  
10  
8
9
(K2) x 4  
Figure 2  
8. Mark the attachment points for the lower mounting slots,  
making sure the attachment points are located on the studs.  
(See Figure 2)  
(K3) x 4  
7 11  
(K2) x 4  
9. Drill 7/32" pilot holes at markings for lower mounting holes.  
(See Figure 2)  
10. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) to attach the mount to the wall through the  
lower mounting holes. (See Figure 2)  
Figure 3  
5. Drill one 5/16" pilot hole at each marking.  
11. Slide rails to approximate center of screen location.  
6. Install an anchor (K1) into each pilot hole using a hammer.  
Installing to a Concrete Wall  
7. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) to attach top of mount to anchors in wall.  
8. Mark the attachment points for the lower mounting slots.  
(See Figure 3)  
9. Drill one pilot hole at each marking for lower mounting  
holes. (See Figure 3)  
CAUTION: MINIMUM HORIZONTAL DISTANCE  
BETWEEN WALL BRACKETS IS 24". Do not place mounting  
brackets closer together than 24".  
1. Determine the center of the display, and where it should be  
located on the wall.  
10. Install an anchor (K1) into each pilot hole using a hammer.  
11. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) to attach the mount to the wall through the  
lower mounting holes. (See Figure 3)  
2. Line up the notches on mount with center of screen marking  
to determine vertical center. (See Figure 1)  
3. Measure up 7-1/2" from the center point to mark location of  
the upper mounting slots. (See Figure 1)  
12. Slide rails to approximate center of screen location.  
Attaching Interface Brackets to Display  
4. Using a level, mark the wall through both upper mounting  
slots. (See Figure 3)  
1. Align the center of the bracket with center of screen.  
(See Figure 4)  
NOTE: The diamond-shape hole in the bracket corresponds to  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL CORDS OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surface is free  
of electrical wires and cables before drilling or installing  
fasteners.  
the center of the mount.  
7
 
XSM/XTM Series  
Installation Instructions  
1
Knobs  
Center of bracket  
Figure 4  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Using screws of  
improper size may damage your display. Properly sized  
screws will easily and completely thread into display  
mounting holes. If spacers are required, be sure to use longer  
screws of the same diameter.  
2
Figure 5  
2. Select correct screws, spacers (if necessary) and washers  
from the hardware bag and attach brackets to back of  
screen. (See Figure 4)  
3. If necessary, the tilt interface bracket knobs may be  
switched to allow the interface brackets to be reversed.  
(See Figure 6)  
Switching Interface Brackets (Optional)  
a. Remove display from mount.  
b. Remove interface brackets from display.  
c. Hold the right interface bracket horizontally, tightly  
gripping it so that spacers do not move.  
d. Remove the knob, washer and screw.  
If an installation situation makes adjusting the location of  
interface brackets necessary, there are several options.  
1. The wall brackets may be adjusted side to side at the point  
of attachment. (See Figure 5)  
2. The location of the left and right interface brackets may be  
switched, with the knobs on the XTM interface brackets  
facing the inside of the mount. (See Figure 5)  
e. Replace the knob, washer and screw in the opposite  
order, with the knob on the inside of the bracket.  
f. Switch the right interface bracket to the left side of the  
wall mount.  
g. Repeat Steps 3c through 3f with the left interface  
bracket.  
8
 
Installation Instructions  
XSM/XTM Series  
Center Line (CL)  
3d  
3e  
Pull strap  
NEVER place both interface brackets to one  
side of the wall mount center line (CL)!  
Knobs to outside  
of brackets  
Figure 6  
Attaching Screen to Wall Mount  
1. Attach wall bracket caps (H) to top and bottom of both wall  
brackets. (See Figure 7)  
Both interface brackets must NEVER be located  
to one side of the wall brackets!  
Figure 8  
XTM Model  
NOTE: Proceed to Step 8 for XSM Model instructions.  
3. Hang top hook of interface brackets onto the top bar of the  
mount. (See Figure 9)  
(H) x 4  
NOTE: The screen initially installs into the "kickstand mode" to  
allow easy cable access.  
Figure 7  
4. Slide screen and bars to desired viewing position.  
5. Route cables between wall and bars.  
2. Adjust Velcro® pull strap (if necessary) so it does not  
extend beyond bottom of screen. (See Figure 8)  
NOTE: NEVER place both interface brackets to one side of the  
wall mount center line! (See Figure 8)  
CAUTION: PINCH POINTS! Keep fingers, hands and  
cables out of pinch point areas.  
NOTE: Do NOT allow both interface brackets to be located on  
same side of wall bracket. (See Figure 8)  
6. Pull downward on the pullstraps and swing inward toward  
wall, latching interface brackets to lower bar and locking  
bottom of screen to the mount. (See Figure 9)  
9
 
XSM/XTM Series  
Installation Instructions  
7. Proceed to Adjusting Roll/Height of Wall Brackets  
10. Move screen towards the wall by pulling display bottom  
away from wall and pushing the interface bracket tabs up  
one notch to the detent which you will be able to feel  
(approximately half way up).  
section.  
11. Push bottom of display toward the wall bracket so that lower  
latch on interface bracket surrounds lower bar of wall  
mount.  
(Screen not shown for clarity)  
Top  
Hook  
12. Raise interface brackets tabs all the way to secure the  
brackets onto the wall mount. (See Figure 10)  
3
Adjusting Roll/Height of Wall Brackets  
NOTE: The height adjust wall brackets allow adjustment of  
+ 1/2".  
1. Turn to right (tighten) to raise side of screen.  
(See Figure 11)  
2. Turn to left (loosen) to lower side of the screen.  
1
Raises screen  
Lowers screen  
2
(G)  
6
Pull straps  
Figure 9  
XSM Model  
(Screen not shown for clarity)  
8. Push interface bracket tab all the way down so that the  
lower mounting slot is blocked. (See Figure 10)  
Figure 11  
Locking XTM Mount (Optional)  
Latch  
closed  
1. Add optional security bracket (L) to the mount.  
(See Figure 12)  
2. Add padlock (not included) to complete security.  
(XTM Shown)  
Latch  
open  
(L)  
Interface  
bracket  
tab  
1
2
12  
8
10  
Figure 10  
9. Hang the top hook of interface brackets onto the top bar of  
the mount. The bottom of the screen will be away from the  
wall.  
Figure 12  
10  
 
Installation Instructions  
XSM/XTM Series  
Locking XSM Mount (Optional)  
Add padlock (not included) to interface bracket tab to lock the  
XSM mount. (See Figure 13)  
Add padlock  
Figure 13  
11  
 
XSM/XTM Series  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Chief Manufacturing, a products  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
division of Milestone AV Technologies  
8805-000259  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
¤2008 Milestone AV Technologies,  
a Duchossois Group Company  
11/08  
 

Bissell Vacuum Cleaner 66E1 User Manual
Black Decker Power Screwdriver 386230 User Manual
Black Decker Toaster T110B User Manual
Blanco Indoor Furnishings 513 690 User Manual
Blue Sea Systems Marine GPS System PN9112 User Manual
Bogen Speaker ASUG1DK User Manual
Campbell Hausfeld Nail Gun NB0030 User Manual
Carrier Appliance Trim Kit 320720 751 THRU 761 User Manual
Carrier Refrigerator Miracool User Manual
Chrysler Automobile 300SRT User Manual