Coleman Tent 2000002596 User Manual

TM  
ROCKWALL 12 TENT  
MODEL 2000002596  
Curved Ridge Pole in  
Curved Ridge Pole  
in sleeve  
Curved Ridge Pole  
in sleeve  
Fig. 6  
Before you begin  
sleeve with Red Marking  
Read all instructions before set up.  
• Select a level site clear of rocks, branches, and other hard or sharp  
objects, to install your tent.  
WARNING: Keep clear of overhead power lines.  
• Do not set up your tent under trees because of potential lightning strikes  
or falling tree limbs in inclement weather.  
Door  
• Secure with all stakes and guylines provided to prevent property damage  
or personal injury.  
• For best results in windy conditions, position narrow end of tent into  
the wind.  
• Enlist the help of at least one other person to assist you when it is time  
to assemble the tent.  
Long Leg Pole  
Short Leg Pole  
Short Leg Pole  
Front of Tent  
8. Rotate all six Leg Poles upright and insert pin on each web  
loop at the side locations as shown. (Fig. 7 & 7A)  
Pole Descriptions  
Fig. 7  
Pole  
Dia.  
Pole  
Pole  
Description  
Qty.  
Repair Kit Replacement Kit  
Long Leg Pole, steel  
(w/ red marking)  
2
4
19mm  
19mm  
N/A  
N/A  
5010000678  
5010000680  
Short Leg Pole, steel  
Curved Ridge Pole, steel  
(w/ red marking)  
1
2
19mm  
19mm  
N/A  
N/A  
5010000677  
5010000679  
Curved Ridge Pole, steel  
7A  
Vertical Door Pole, black,  
short w/rubber tips  
1
1
6.3mm 5010000543  
6.3mm 5010000543  
5010000545  
5010000545  
Door Pole, black,  
long w/rubber tips  
Pin  
Self-Rolling Window Spring Descriptions  
9. Stretch tent to finished size:  
• Push in button on Leg Pole while  
twisting lower Leg Pole section  
counterclockwise (Fig. 8);  
Color Code Description  
Qty.  
Length Replacement Part No.  
Fig. 8  
Green  
Orange  
1
10  
610mm  
670mm  
5010000627  
5010000628  
Upper  
• Pull up on top Leg Pole section until  
tent is taut;  
Leg Pole  
Section  
CAUTION: “Springs” may have sharp edges. Handle with care to avoid  
injury. Keep out of reach of children.  
• Twist the lower Leg Pole clockwise  
until the button locks into the center  
or lowest hole;  
Button  
Center Hole  
Lower Hole  
• Repeat on remaining Leg Poles.  
10. Locate Frame Clips on front and back of  
tent; then attach to Leg Poles as shown.  
(Fig. 9)  
To Set Up Tent  
1. Unfold tent and spread out on a clean, level surface with the door  
facing the desired direction.  
Lower  
Leg Pole  
Section  
11. Insert plastic stakes through  
web straps located at bottom  
of each Leg Poles; then drive  
in to secure. (Fig. 10)  
Fig. 1  
Curved Ridge Poles (3)  
Leg Poles,  
short (4)  
Leg Poles,  
long (2)  
Fig. 9  
Fig. 10  
2. Assemble six, steel, shock-corded, Leg Poles.  
(Fig. 1)  
3. Push down on steel button on tapered end  
and insert into end with four holes.  
NOTE: Make sure steel button locks into  
third hole on pole as shown. (Fig. 2)  
4. Assemble three, steel, shock-corded, curved  
Ridge Poles. (Fig. 1)  
Hinged, Rigid Door  
Button in  
third hole  
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);  
then insert through zippered vertical pole sleeve on hinged side of  
door. (Fig. 11)  
Fig. 2  
2. Insert end of Vertical Door Pole into bottom hinge plate, apply  
pressure to form a slight bow, then insert other tip of pole into top  
hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)  
3. Assemble Door Pole (longer black pole with plastic cap tips); then  
insert into zippered pole sleeve at top of door. (Fig. 14)  
4. Insert end of Door Pole into top hinge plate, apply pressure to form  
a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)  
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)  
5. Stretch four corners of tent until taut; then  
drive plastic stake web strap of each to  
secure. (Fig. 3)  
Fig. 3  
6. Insert Ridge Pole (with red marking) into center sleeve on top of tent  
with the red trim (Fig. 4 & 6). Insert the remaining curved Ridge Poles  
into the other two sleeves on top of tent.  
7. Insert curved end of Leg Pole (with red marking) into the ends of the  
Ridge Pole (with red dot). Insert curved end of remaining short Leg  
Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)  
Fig. 11  
Fig. 12  
Fig. 13  
Vertical Pole  
Sleeve  
Door Hinge  
Fig. 4  
Ridge Pole with  
Red Marking  
Curved  
Fig. 15  
Fig. 14  
Ridge Pole  
Curved End of  
Long Leg Pole  
with Red  
Marking  
Sleeve  
with Red  
Trim  
Top  
Door  
Pole  
Sleeve  
Hinge  
Sleeve  
with Red  
Trim  
Fig. 16  
Fig. 5  
(continued on other side)  
 

Cooper Lighting Indoor Furnishings UMB16 User Manual
Cooper Lighting Stud Sensor CPD 1200H User Manual
Curtis MP3 Player MP257 User Manual
Curtis Telephone T223 User Manual
Dell Server E11S User Manual
Desa Tech Indoor Fireplace CGFB32CC User Manual
D Link Network Router DVG G5402SP User Manual
Electro Voice Microphone PL70 N D User Manual
Electro Voice Portable Speaker DMC 2181A User Manual
Genesis Advanced Technologies Cordless Saw GJS450 User Manual