Owner's Manual
®
STOP
DETHATCHER FOR SWEEPERS
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
Model No. 486.242182
CAUTION:
• Safety
Before using this product, read
this manual and follow all Safety
Rules and
• Assembly
• Operation
• Maintenance
• Parts
Operating Instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
FORM NO. 41505 rev. (06/07/10)
PRINTED IN U.S.A.
HARDWARE PACKAGE CONTENTS
14
8
5
6
7
15
16
9
17
13
12
11
10
19
18
20
NOT SHOWN FULL SIZE
26
21
24
27
25
22
23
REF. PART NO. QTY.
DESCRIPTION
REF. PART NO. QTY.
DESCRIPTION
5
6
7
8
9
10
11
12
13
14
15
16
46526
47025
43085
48813
48811
3
2
7
2
1
2
2
Hex Bolt, 1/2-13 x 3-1/2"
Hex Bolt, 5/16-18 x 3-1/2"
Hex Bolt, 5/16-18 x 1-1/2"
U-Bolt, 1/4-20
Transport Hook
Washer, 5/16"
17
18
19
20
21
22
23
24
25
26
27
48115
48812
43003
43015
44481
48917
25054
46499
741-0248
42212
46853
3
2
4
4
2
2
2
2
4
1
2
Jam Nut, Nylock 1/2-13
Clevis Pin, 5/16" x 1-3/8"
Lock Washer, 3/8"
Hex Nut, 3/8-16
Vinyl Cap
Clamp
Bracket, U-Bolt Clamp
Spacer
43081
R19171616
43070
Washer, 1/2"
14 Washer, 3/8"
43055
47189
47810
43019
2
4
9
1
Hair Cotter Pin, 3/32"
Flange Bearing
Double Transport Hook
U-Bolt, 3/8
Nylock Nut, 1/4-20
Nylock Nut, 5/16-18
Jam Nut, Plain 1/2-13
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
3
ASSEMBLY
CARTON CONTENTS
NOTE: On sweepers smaller than 42", use only five spring
tines.
1. Spring Tines (7)
2. Frame Assembly
3. Gauge Wheel
•
Assemble a vinyl cap onto each end of the frame tube.
See figure 1.
4. Mount Brackets (2)
5/16" x 1-1/2"
HEX BOLT
VINYL CAP
3/8" WASHER
1
5/16" NYLOCK NUT
VINYL CAP
2
4
FIGURE 1
3
•
•
Assemble a 1/2" washer, the wheel, another 1/2"
washer and the 1/2" plain jam nut onto the
1/2" x 3-1/2" hex bolt. See figure 2.
Insert the bolt through the welded bracket and
assemble the 1/2" nylock jam nut onto the bolt. Adjust
the nuts so that there is no end play in the wheel and
then tighten the nuts securely against the welded
bracket. Make sure the wheel still turns freely. See
figure 2.
TOOLS REQUIRED FOR ASSEMBLY
(1)
(2)
(2)
(1)
7/16" Wrench
1/2" Wrenches
3/4" or Adjustable Wrenches
Knife
Use this hole for
42" & 46" sweepers
Use this hole for
smaller sweepers
REMOVAL OF PARTS FROM CARTON
•
Remove all parts and hardware packages from the
carton. Lay out all parts and hardware and identify
using the illustrations on pages 3 and 4.
Turn the frame assembly as shown in figure 1.
Assemble seven spring tines to the top of the frame
tube. Use a 5/16" x 1-1/2" hex bolt, two 3/8" flat
washers and a 5/16" nylock nut for each spring tine.
Place one 3/8" flat washer on top of the frame tube
and the second 3/8" flat washer on top of the spring
tine. See figure 1.
1/2" NYLOCK
JAM NUT
1/2" JAM NUT
1/2" WASHER
•
•
1/2" WASHER
1/2" x 3-1/2"
HEX BOLT
FIGURE 2
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
4
SWEEPERS WITH TWO HITCH TUBES
If you have a 30" sweeper, skip to figure 6.
Skip to page 6 for sweepers with single hitch tubes.
•
Make sure the sweeper height adjustment handle is
still set to about the middle of it's adjustment range.
Center the dethatcher with the sweeper.
Assemble the keeper brackets (bend to the inside)
to the sweeper's hitch tube, outside of the conduit
clamps. Use a u-bolt and two 1/4" nylock nuts per
bracket. Position the keeper brackets against the sides
of the conduit clamps, approximately perpendicular
to the ground. Tighten the nuts without bending the
keeper brackets. See figure 5.
•
•
•
Assemble a conduit clamp onto each end of the
sweeper height adjustment tube so that the straight
part of the clamp is on top of the tube.
Remove the hitch brackets from the sweeper's hitch
tubes. Slide the transport hook onto the L.H. hitch
tube as shown in figure 3.
•
•
Reassemble the hitch brackets and bolts to the hitch
tubes. Refer to your sweeper owner's manual.
KEEPER BRACKET
U-BOLT
TRANSPORT
HOOK
HEIGHT ADJ.
TUBE
CONDUIT
CLAMP
FIGURE 3
1/4" NYLOCK NUT
•
Connect the sweeper to the tractor. Set the sweeper
height adjustment handle to about the middle of it's
adjustment range.
FIGURE 5
•
•
Place the dethatcher in front of the sweeper housing,
underneath the hitch tubes.
Connect the dethatcher to the conduit clamps using
two 5/16" x 1-3/8" clevis pins, 5/16" washers and
3/32" hair cotter pins. See figure 4.
•
Lift the front of the dethatcher and secure it in
transport position using the transport hook. See
figure 6.
HEIGHT ADJUSTMENT
MIDDLE SETTING
TRANSPORT HOOK
5/16" x 1-3/8"
CLEVIS PIN
5/16" WASHER
3/32" HAIR
COTTER PIN
FIGURE 6
FIGURE 4
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
5
SWEEPERS WITH A SINGLE HITCH TUBE
•
Assemble one 5/16 x 3-1/2" hex bolt and 5/16" nylock
nut to the bottom hole of each mount bracket.
NOTE: The dethatcher attaches to the sweeper's offset
tube. This prevents you from offsetting the sweeper.
•
Assemble the four bearings to the two spacers and
then slide each through a clamp.
5/16" NYLOCK NUT
CLAMP
BEARING
BEARING
5/16 x 3-1/2"
HEX BOLT
SPACER
FIGURE 7
FIGURE 9
•
Fasten each clamp to the spring mount frame
assembly using one 5/16 x 1-3/8" clevis pin, 5/16"
washer, and 3/32" hair cotter pin.
•
Attach each of the bearing, spacer, and clamp
assemblies to a mount bracket using a 1/2 x 3-1/2" hex
bolt and 1/2" nylock jam nut.
5/16 x 1-3/8"
CLEVIS PIN
1/2" NYLOCK
JAM NUT
5/16" WASHER
1/2 x 3-1/2"
HEX BOLT
3/32" HAIR
COTTER PIN
FIGURE 10
FIGURE 8
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
6
•
Secure the two mount brackets to the drawbar offset
tube of the sweeper using two 3/8" U-bolts, four 3/8"
lock washers and four 3/8" hex nuts. Do not tighten
yet.
3/8" U-BOLT
3/8" LOCK WASHER
3/8" HEX NUT
FIGURE 11
•
•
Center the dethatcher on the front of the sweeper
housing.
Place the double transport hook onto the sweeper hitch
tube. Lift up the front of the dethatcher and slide it into
the double hooks to secure it in the transport position.
Tighten the U-bolts and nuts assembled in figure 11.
•
DOUBLE TRANSPORT HOOK
FIGURE 12
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
7
OPERATION
USING THE DETHATCHER
HOW TO USE YOUR DETHATCHER
Regular removal of thatch is critical to the maintenance
of a healthy lawn. Thatch is layer of stems, clippings,
runners, roots and leaves that have not decayed.
Excessive thatch prevents air, water and fertilizer from
reaching the roots. The dethatcher will effectively dislodge
RAISING/LOWERING THE DETHATCHER
•
To raise the dethatcher for transport, lift up on the
front of the dethatcher and secure it with the transport
hook. Lower the dethatcher by releasing the transport
hook.
excessive thatch from your lawn.
•
Start with the tractor in low gear. Vary the forward
speed to determine the best speed for maximum
dethatcher performance.
SETTING THE OPERATING POSITION
•
The operating height of the dethatcher is controlled
by the gauge wheel at the front of the dethatcher
and is not adjustable. The correct wheel position
was determined in figure 2 when you assembled the
wheel.
•
•
Use a crisscross pattern to achieve the most even
removal of thatch.
On slopes, always operate in an up and down
direction only.
•
Set the sweeper to the desired operating height. (The
best height is usually with the brushes set about 1/2"
down into the grass.) Refer to your sweeper owner's
manual.
•
•
Avoid extremely sharp turns.
Avoid towing the dethatcher across sudden steep
dips in the ground while dethatching. Loss of ground
contact with the gauge wheel could cause the
dethatcher to be pulled back underneath the sweeper.
MAINTENANCE / STORAGE
CUSTOMER RESPONSIBILITIES
•
Read and follow the maintenance schedule and the maintenance procedures listed in this section.
MAINTENANCE SCHEDULE
Fill in dates as you
complete regular service.
Service Dates
Check for loose fasteners
Check for worn or damaged parts
Cleaning
X
X
X
X
X
•
•
Before each use, check all nuts and bolts for
tightness.
•
•
If rust appears on the spring tines, sand lightly and
coat with enamel paint.
Clean after each use to help prevent rust.
Always store in a dry area, and coat exposed metal
with light oil when not in use.
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
8
PARTS
REPAIR PARTS FOR MODEL 486.242182 DETHATCHER
4
27
5
7
6
12
17
15
18
2
19
20
10
22
12
25
26
25
24
21
13
18
1
15
10
22
17
8
16
23
14
11
13
11
3
9
21
5
REF. PART NO. QTY.
DESCRIPTION
REF. PART NO. QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
64650
46761
48098
27117
46526
47025
43085
48813
48811
43081
R19171616
43070
43055
47189
1
7
1
2
3
2
7
2
1
2
2
Spring Mount Frame Assem.
Spring Tine
Gauge Wheel
15
16
17
18
19
20
21
22
23
24
25
26
27
47810
43019
48115
48812
43003
43015
44481
48917
25054
46499
741-0248
42212
46853
41505
9
1
3
2
4
4
2
2
2
2
4
1
2
1
Nylock Nut, 5/16-18
Jam Nut, Plain 1/2-13
Jam Nut, Nylock 1/2-13
Clevis Pin, 5/16" x 1-3/8"
Lock Washer, 3/8"
Hex Nut, 3/8-16
Vinyl Cap
Clamp
Bracket, U-Bolt Clamp
Spacer
Mount Bracket
Hex Bolt, 1/2-13 x 3-1/2"
Hex Bolt, 5/16-18 x 3-1/2"
Hex Bolt, 5/16-18 x 1-1/2"
U-Bolt, 1/4-20
Transport Hook
Washer, 5/16"
Washer, 1/2"
Flange Bearing
Double Transport Hook
U-Bolt, 3/8
14 Washer, 3/8"
2
4
Hair Cotter Pin, 3/32"
Nylock Nut, 1/4-20
Owner's Manual
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
9
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
10
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
11
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
1-800-469-4663 (Canada)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
|