• MC-MP-DY4 Spa Pack •
The Quick Reference Card provides a quick overview of your spa's main
functions and the operations accessible with your digital control pad.
Starting Pump 1:
Turning the light on:
Press Pump 1 to turn Pump 1 on at low
speed. Pressing a second time turns Pump 1
to high speed. A third time turns Pump 1 off.
When at high speed, a built-in timer turns
pump off after 20 minutes and when at low
speed after 2 hours, unless it has been
manually deactivated.
Pressing Light key once turns light on at high
intensity. Pressing a second time turns light to
low intensity. A third time turns light off.
A built-in timer turns light off after 2 hours,
unless it has been manually deactivated.
the second press. If the LEDs remain off for
more than 5 sec., the color/
display sequence will reset and start back at
the beginning the next time the Light key is
pressed. Color/ display sequences are:
The "Light" icon is displayed when
light is on at high intensity. It flashes
when light is on at low intensity.
1• LEDs light up and slowly cycle through all
six colors. The slow cycle restarts at the
beginning and repeats.
The "Pump 1" icon lights up when
Pump 1 is on at high speed. It flashes
when Pump 1 is on at low speed.
2• LEDs light up and remain on in Aqua.
3• LEDs light up and remain on in Purple.
4• LEDs light up and remain on in Blue.
5• LEDs light up and remain on in Gold.
6• LEDs light up and remain on in Green.
7• LEDs light up and remain on in Red.
8• LEDs light up for 2 sec., flash off, then
flash on in the next color until all six colors
have been displayed. The flashing cycle
then repeats itself.
Fiber Box Option: If spa has an optional fiber
box only, pressing Light key turns fiber box
(motor & light) on. Pressing again turns fiber
box motor off but leaves light on. A third time
turns both motor and light off. A built-in timer
turns fiber box off after 2 hours, unless it has
been manually deactivated. The "Light" icon is
displayed when fiber box light is on. It flashes
when fiber box motor and light are on at the
same time.
Starting Pump 2:
Press Pump 2 once to turn Pump 2 on at low
speed. Pressing a second time turns Pump 2
to high speed. A third time turns pump off.
A built-in timer turns pump off after 20 mi-
nutes, unless manually deactivated first.
9• LEDs flash on/off quickly for a strobe light
effect. A built-in timer turns lights off after
2 hours unless manually deactivated first.
The "Pump 2" icon lights up when
Pump 2 is on at high speed. It flashes
when Pump 2 is on at low speed.
LED Light Option: If spa has an optional LED
light, Press Light key to turn LED lights on. To
advance to the next color/display setting, press
Light key twice. The LEDs will go off with the
first press, then back on in the next setting with
The "Light" icon is displayed
when light is on.
Starting the blower:
Press Blower to turn blower on at high speed.
Press a second time to turn blower to low
speed. A third time turns blower off. A built-in
timer turns blower off after 20 minutes, unless
manually deactivated first.
Time & temperature display:
Temperature display unit:
Press and hold Light key for 5 seconds to
display water temperature in either Fahrenheit
(˚F) or Celsius (˚C).
The display toggles every 5 seconds alternately
showing the hourly time and the current water
temperature.
The "Blower" icon lights up when
blower is on at high speed. It flashes
when blower is on at low speed.
The filter cycle is suspended if the water temperature raises more than 2˚F (1˚C) above Set
Point or if a pump has been started manually. The "Filter" icon will blink (on 0.5 second,
off 0.5 second, on 0.5 second, off 1.5 seconds).
Automatic water heater start:
When water temperature is 1˚F (0.5˚C)
lower than the Set Point, the heater will
automatically turn on until water tempera-
ture reaches Set Point plus 1˚F (0.5˚C).
Troubleshooting
The "Heater" icon lights up when the
heater is on. It flashes when there is a
request for more heat but the heater
has not yet started.
Pumps have started up for
one minute on several
occasions and "Filter Cycle"
icon is flashing.
Water temperature is
displayed.
3 flashing dots are dis-
played.
Setting water temperature:
Water temperature in the
spa has reached 112˚F
(44˚C).
A problem has been de-
tected.
Use Up or Down arrow key to regulate water
temperature. The temperature setting will be
displayed for 5 seconds to confirm your new
selection.
Not a bug but a feature!
Do not enter the water!
Check and open water
valves. Clean filters if nec-
essary. Check water level.
Add water if needed.
Our Smart Winter Mode
protects your system from
the cold by automatically
turning the pumps on for
one minute several times a
day to prevent water from
freezing in pipes.
Do not enter the water!
Allow water to cool down.
The system will reset au-
tomatically when water
reaches 109˚F (43˚C).
The "Set Point" symbol indicates the
desired temperature, NOT the current
water temperature!
Water temperature can be adjusted by 1˚ in-
crements from 59 to 104˚F (15 to 40˚C).
Shut power off and power
your spa up again to reset
the system.
Call your dealer or service
supplier if problem persists.
Inverted display:
The display is flashing.
Call your dealer or service
supplier if problem persists.
Press and hold Pump 2 for 5 seconds to invert
the display. Note that the ˚F or ˚C icon is not
displayed in reverse mode. Follow the same
procedure to return to default mode. If a
power-up occurs, the display always returns
to default mode.
A power failure has
occurred. Press any key
to reset the system, then
reprogram all desired
parameters.
Download from Www.SQomuaicnukaRls.ecfoemr.eAnllcMeaCnuaarlds Search And Download.
Temperature
unit
Step
Programming
7Sequence
Time of day
Step 2 Filter cycle start time
Step 1
Filter cycle duration
Step 3
Step 4
Step 5
Step 6
Step 7
Filter cycle frequency
Filter Cycle
icon
Heater
icon
Up & Down
arrows
Economy mode start time
Economy mode duration
Programming Mode
icon
Economy Mode
icon
Lock
icon
Storing settings in memory & returning to Normal mode
Digital control pad lockout
Step 1- Time of day
This function allows you to prevent unauthorized parameter
setting of the unit. This feature is especially helpful when young
children have access to the keypad.
Setting the time:
1- Enter Programming mode by holding
Prog. key pressed down for 2 seconds.
2- The display will show the current time.
3- Use Up and Down arrows to change
the hours.
10:25
11:43
am
There are two modes you can choose from: Full lock or Partial
lock. Full lock means that all keypad functions are locked. Partial
lock means that the basic functions of the spa will remain accessi-
ble (pumps, blower and light), but it will be impossible to change
the temperature Set Point, to override the Economy mode or
to enter the Programming mode.
pm
4- Prog. key a second time to select the
minutes.
5- Use Up and Down arrows to change
setting.
When control pad is locked, the "Lock" icon will be displayed.
Steps 2 & 3- Filter cycle start time & duration
Locking your digital control pad:
The system automatically performs two filter cycles per day, at
12-hour intervals. During the filter cycle, Pumps 1 & 2 and the
blower will run the first minute, then Pump 3 will run for one
minute. Pump 1 will then run at low speed for a programmed
number of hours. The "Filter Cycle" icon lights up when a filter
cycle is on.
1- Press and hold Pump 1 key for
5 seconds.
LocP
2- The display will show LocP, with "P"
representing Partial lock.
3- Release the key and the keypad will be
LocF
in Partial lock mode. Keep key pressed
down for 5 more seconds if you want
to be in Full lock mode. The "LocF"
message will then be displayed.
To program a filter cycle, you must enter: 1) the time you want
the cycle to start and 2) the duration of the cycle. If no filtering is
required, the duration should be set to "0". For continuous
filtering, the filter cycle duration should be set to "12:00".
When control pad is locked, all automatic functions of the system
run as usual. If a key is pressed down, a "LocP" or "LocF"
message will be displayed for 1 second. To unlock the keypad,
simply press and hold Pump 1 key again for 5 seconds.
Setting filter cycle start time:
1- Press Prog. key a third time.
2- The display will show FSxx, with "xx"
representing the starting hour.
3- Use Up and Down arrows to change
setting.
FS01
FS12
When control pad is unlocked, the "Ulock" icon will be displayed.
Economy mode
Setting filter cycle duration:
1- Press Prog. key a fourth time.
Press Econo key to switch from Normal mode to Economy
mode. To save energy, the Economy mode Set Point is 20˚F
(11˚C) below the Normal mode Set Point.
2- The display will show Fdxx, with "xx"
representing the duration in hours.
3- Use Up and Down arrows to change
setting.
Fd00
Fd12
The "Economy Mode" icon lights up when Economy
mode is on.
Step 4- Filter cycle frequency
There are 3 available Economy operating modes:
noEc:
Ec 1:
Ec 2:
No Economy mode
Economy mode always on
Economy mode on during a programmed
number of hours (see Steps 5 & 6*)
Setting filter cycle frequency:
1- Press Prog. key a fifth time.
2- The display will show FFxx, with "xx"
representing the frequency per day.
3- Use Up and Down arrows to change
setting.
FF01
Selecting the desired Economy mode:
FF04
1- Press and hold Econo key for
more than 2 seconds.
2- The display will show the current
mode (noEc, Ec 1 or Ec 2).
noEc
Ec 1
Steps 5 & 6- Economy mode start time & duration*
Setting Economy mode start time:
3- Keep key pressed down until the
desired mode is displayed.
1- Press Prog. key a sixth time.
After 5 seconds, the new setting will be programmed.
2- The display will show ESxx, with "xx"
representing the starting hour.
3- Use Up and Down arrows to change
setting.
ES10
ES08
Setting Economy mode duration:
Summary of control panel parameters
1- Press Prog. key a seventh time.
2- The display will show Edxx, with "xx"
representing the duration in hours.
3- Use Up and Down arrows to change
setting.
Ed01
FSxx Filter cycle start time
Fdxx Filter cycle duration
FFxx Filter cycle frequency
ESxx Economy mode start time
Edxx Economy mode duration
LocX Control pad lockout
Ed04
Step 7- Storing settings in memory
Press Prog. key an eighth time to store settings in the system's
non-volatile memory and to return to Normal mode.
E
Smart
Winter
TM
Mode
9919-100494-B
|