Earthquake Sound Speaker MC6 User Manual

MARI NE  
The Sound That Will Move You.  
EARTHQUAKE MARINE SPEAKERS  
Owner’s Manual & Warranty  
M5  
2-WAY 5” COAXIAL SPEAKER  
M6  
2-WAY 6” COAXIAL SPEAKER  
MC5  
5” MATCHED COMPONENT SET  
MC6  
6” MATCHED COMPONENT SET  
The Sound That Will Move You.  
Earthquake Sound reserves the right to amend details of the specifications without notice.  
Copyright © Earthquake Sound Corporation  
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545 • Phone: 510-732-1000 Fax: 510-732-1095  
earthquakesound.com  
 
MC Crossover Dimensions  
M5 COAXIAL DIMENSIONS  
This diagram displays only the crossover.  
Mounting components vary in size.  
A
Grille tray outer  
diameter  
B
165.5mm • 6.51”  
A
A
Height  
.97" • 24.7mm  
1.64" • 41.8mm  
2.08" • 53mm  
.94" • 24mm  
B
C
D
E
Grille protrusion  
Mounting depth  
Magnet width  
Cut out hole  
21mm • .82”  
Ba  
B
Width  
Width  
a
C
C
62mm • 2.44”  
B
87mm • 3.42”  
D
Depth  
D
130.0mm • 5.11”  
B
E
A
MC, Tweeter Dimensions  
M6 COAXIAL DIMENSIONS  
This diagram displays only the raw tweeter.  
Mounting components vary in size.  
C
D
A
Grille tray outer  
diameter  
B
190.2mm • 7.48 ”  
26mm • 1.02”  
59mm • 2.32”  
90mm • 3.54”  
147mm • 5.78”  
A
Trim Ring Diameter  
2.15", 54.7mm  
1.79”, 45.6mm  
.925", 23.5mm  
.71”, 18.2tmm  
B
C
D
E
Grille protrusion  
Mounting depth  
Magnet width  
Cut out hole  
B
Cut Out Hole Diameter  
C
C
Total Depth  
B
A
D
Mounting Depth  
A
D
E
A
MC5 WOOFER DIMENSIONS  
A
Grille tray outer  
diameter  
B
MARINE MATCHED COMPONENT SPECIFICATIONS  
166.5mm • 6.55”  
MC5 (2-way)  
MC6 (2-way)  
Model  
B
C
Grille protrusion  
20mm • .78”  
Woofer  
• 5” UV treated poly injection cone body  
• 25mm (over 1”) ASV voice coil  
• Butyl rubber surround  
• 6.5” UV treated poly injection cone body  
• 30mm (almost 1.25”) ASV voice coil  
• Butyl rubber surround  
C
61mm • 2.40”  
Mounting depth  
Magnet width  
a Magnet width  
+ crossover  
Tweeter  
• 20mm • .78" PEI dome  
• 20mm • .78" PEI dome  
D
D
Crossover Networks • 2-way network  
• 2-way network  
• Completely sealed  
87mm • 3.42”  
+ 20mm • .78” for x-over  
• Completely sealed  
D
E
Frequency Response  
Rec. Amp power  
Sensitivity  
50Hz-22kHz  
45Hz-22kHz  
Da  
E
Cut out hole  
129.0mm • 5.07”  
75 watts RMS • 145 watts max  
89 dB @ 1W/1M  
85 watts RMS • 165 watts max  
89 dB @ 1W/1M  
A
Nominal Impedance  
4 ohm  
4 ohm  
MC6 WOOFER DIMENSIONS  
MARINE COAXIAL SPECIFICATIONS  
Model  
M5 (2-way)  
M6 (2-way)  
A
Grille tray outer  
diameter  
B
190.5mm • 7.5”  
Woofer  
• 5” UV treated poly injection cone body  
• Sealed motor structure  
• 6” UV treated poly injection cone body  
• Sealed motor structure  
B
C
Grille protrusion  
29.5mm • 1.16”  
59mm • 2.32”  
• 25mm (over 1”) VC  
• 25mm (over 1”) VC  
• Butyl rubber surround  
• Butyl rubber surround  
C
Tweeter  
• 20mm • .78" mylar dome  
50-130 Watts RMS  
65Hz - 20kHz (±3dB)  
89 dB @ 1W/1M  
4 ohm  
• 20mm • .78" mylar dome  
60-180 Watts RMS  
55Hz to 20kHz (±3dB)  
90 dB @ 1W/1M  
4 ohm  
Mounting depth  
Magnet width  
a Magnet width  
+ crossover  
Rec. Amp power  
Frequency Response  
Sensitivity  
D
D
90mm •3.54 ”  
+ 20mm • .78” for x-over  
D
E
Da  
E
Cut out hole  
147mm • 5.78”  
Nominal Impedance  
A
All specifications are subject to change without notice.  
4
EARTHQUAKE SOUND  
EARTHQUAKE SOUND • MARINE COMPONENT & COAXIAL SPECIFICATIONS  
5
 
CUSTOM SPEAKER INSTALLATION  
SURFACE MOUNT  
FLUSH MOUNT COMPLETE ASSEMBLY  
NOTE:  
GRILLE 4 S H E E T M E T A L  
SCREWS PER SPEAKER  
GRILLE TRAY  
Cut diameter: EQM-T=2.15” (54.7mm)  
Push assembled tweeter through cut out hole  
INSTALLATION APPLIES  
TO BOTH COMPONENT  
AND COAXIAL SPEAKERS  
Cup Mount  
First pre-wire  
your water craft  
if not using stock  
p l a c e m e n t .  
Mount cup in  
desired place.  
T h e n p u s h  
tweeter inside  
cup until you  
hear the snap.  
This indicates  
a secure fit.  
Fasten the panel  
clamp down from  
behind the panel.  
Panel  
Twist on nut  
until the  
tweeter is  
secured  
Panel Clamp  
FACTORY REPLACEMENT INSTALLATION  
NOTE:  
4
S H E E T M E T A L  
SPEAKER  
FACTORY CUTOUT  
MOUNTING CLIPS  
INSTALLATION APPLIES  
TO BOTH COMPONENT  
AND COAXIAL SPEAKERS  
SCREWS PER SPEAKER  
NOTE:  
COMPONENT SET WIRING DIAGRAM  
Hand tighten the screws  
in a crisscross pattern to  
avoid bending the speaker  
basket or stripping screws.  
WOOFER  
TWEETER  
AMPLIFIER  
CROSSOVER  
All specifications are subject to change without notice.  
6
EARTHQUAKE SOUND  
EARTHQUAKE SOUND • INSTALLATION  
7
 

CMS Products Coffeemaker 674 User Manual
Craftsman Blower 31679479 User Manual
Crate Amplifiers Stereo Amplifier GT80 User Manual
Crown Stove CSHB60 90XE User Manual
Cub Cadet Washer 59A40003727 User Manual
Curtis Flat Panel Television LCD1905A User Manual
Electro Voice Speaker System HP420 User Manual
Everpure Water System A 20 20 User Manual
Exido Scale 246 030 User Manual
Garland Charcoal Grill RBA Series User Manual