T4262
Please keep this instruction sheet for future reference,
as it contains important information.
Adult supervision is required.
Never use near steps.
Choose areas for riding that are free of obstacles.
Learn to stop safely.
Use with caution as this product requires skill to operate safely to
avoid falls, collisions, and injuries to yourself (the rider) and others.
Maximum weight: 44 lbs. (20 kg).
For ages between 9 months and 3 years.
Requires three “AA” batteries (included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
fisher-price.com
Consumer
Information
Assembled Parts
CAUTION
Base
This package contains
small parts in an
unassembled state. Adult
assembly is required.
• Wipe this toy with a clean cloth
dampened with a mild soap and
water solution. Do not immerse
this toy.
• This toy has no consumer
serviceable parts.
• Do not take this toy apart. Do not
drop this toy on a hard surface.
• Periodically inspect this product
for wear or damage. Check all
nuts and bolts, and tighten as
needed. Replace worn or broken
parts immediately.
2 Rear Wheels
2 Handles
2 Front Wheels
ICES-003
This Class B digital apparatus
complies with Canadian ICES-003.
Operation is subject to the following
two conditions: (1) this device may
not cause harmful interference
and (2) this device must accept
any interference received,
Head
including interference that may
cause undesired operation.
NMB-003
Cet appareil numérique de
Front Axle
la classe B est conforme à la
norme NMB-003 du Canada.
L’utilisation de ce dispositif est
autorisée seulement aux conditions
suivantes: (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du
dispositif doit être prêt à accepter
tout brouillage radioélectrique
reçu, même si ce brouillage est
susceptible de compromettre le
fonctionnement du dispositif.
#8 x 3/4" (1,9 cm) Screw - 10
Shown Actual Size
Tighten and loosen all screws
with a Phillips screwdriver.
Do not over-tighten.
3
Assembly
Rear Wheels
Base
1
BOTTOM VIEW
• Place the base on a flat surface
so that the bottom faces you.
• Insert and “snap” the rear wheels
into the sockets in the base.
3
• Fit the front wheel assembly to
the base, as shown.
Hint: This may require some force.
• Pull up on the rear wheels to be
sure each is secure to the base.
• Insert four screws into the front
wheel assembly and tighten.
Front Wheels
Head
Front Axle
4
FRONT VIEW
• Turn the base assembly upright.
• Fit the head onto the
base assembly.
2
• Fit the front wheels to the front
axle, as shown.
• Insert a screw into each front
wheel and tighten.
4
Assembly
Rewarding Lights
and Music!
Screws
5
Screws
• Insert two screws into each side
of the head and tighten.
• Slide the power/volume switch
on the back of the dino's head
to ON with low volume or ON
Handles
with high volume
.
• Press the lights or roll the dino
along for music and fun sounds!
• When you are finished playing
with this toy, slide the power/
volume switch OFF
.
• Wipe this toy with a clean cloth
dampened with a mild soap and
water solution. Do not immerse
this toy.
• This toy has no consumer
serviceable parts.
• Do not take this toy apart. Do not
drop this toy on a hard surface.
• Periodically inspect this product
for wear or damage. Check all
nuts and bolts, and tighten as
needed. Replace worn or broken
parts immediately.
6
BACK VIEW
• Fit a handle into the socket on
each side of the head.
Hint: Turn each handle so that
each fits into the socket.
• Push both handles until the
"snap" together.
• Pull on each handle to be sure
they are secure in the sockets.
5
Battery Replacement
Battery Safety
Information
1,5V x 3
“AA” (LR6)
In exceptional circumstances,
batteries may leak fluids that can
cause a chemical burn injury or
ruin your product. To avoid
battery leakage:
• Do not mix old and new
batteries or batteries of different
types: alkaline, standard
(carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated
inside the battery compartment.
• Remove batteries during long
periods of non-use. Always
remove exhausted batteries from
the product. Dispose of batteries
safely. Do not dispose of this
product in a fire. The batteries
inside may explode or leak.
• Never short-circuit the
battery terminals.
• Use only batteries of the same or
equivalent type as recommended.
• Do not charge non-
rechargeable batteries.
• Remove rechargeable batteries
from the product before charging.
For best performance, we
recommend replacing the
batteries that came with three
"AA" (LR6) alkaline batteries.
• Locate the battery compartment
on the side of the dino.
• Loosen the screws in the battery
compartment door. Remove
the battery compartment door.
Remove the exhausted batteries
and dispose of them properly.
• Insert three, new "AA" (LR6)
alkaline batteries.
• Replace the battery compartment
door and tighten the screws.
• If this toy begins to operate
erratically, you may need to reset
the electronics. Slide the power/
volume switch off and then
back on.
• When lights or sounds from
this toy become faint or stop,
it’s time for an adult to change
the batteries!
• If removable, rechargeable
batteries are used, they are
only to be charged under
adult supervision.
• Protect the environment
by not disposing of this
product with household
waste (2002/96/EC).
Check your local authority
for recycling advice
and facilities.
6
Walker
To change to Walker mode, follow these steps:
Latch
Press
1
2
Slide
1
2
Bottom View
• Spread the seat halves until they
“click” in place. Turn the toy
over. It is now ready to be used
as a walker.
• Turn the toy over. Press and slide
the latch to an open position,
as shown.
7
To change to Ride-On mode, follow these steps:
Press
Latch
1
2
Top View
Bottom View
• While pressing the seat button,
close the seat halves. Turn
the toy over.
• Slide the latch to a closed
position. It should “click” into
place.Turn the toy over. It is now
ready to be used as a ride-on.
8
|