All about the
Use & Care
of your Washer
TABLE OF CONTENTS
Important Safety Instructions........................... 2-4
Operating Instructions................................... 5-11
Care and Cleaning............................................ 12
Avoid Service................................................... 13
Warranty ......................................................... 14
Français........................................................... 15
Español ........................................................... 29
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, electrical shock, or injury to persons when using this washer, comply with the basic
warnings listed below. Failure to comply with these warnings could result in serious personal injuries.
You can be killed or seriously injured if you don’t follow these Important Safety Instructions:
PREVENT FIRE
PROTECT CHILDREN
•
Do not wash items that have been previously cleaned
in, soaked in, or spotted with gasoline, cleaning sol-
vents, kerosene, cooking oils, waxes, etc. Do not store
these items on or near the washer. These substances
give off vapors or chemical reactions that could ignite
or explode.
•
Do not allow children to play on or in the washer.
Close supervision of children is necessary when the
washer is used near children. As children grow, teach
them the proper, safe use of all appliances.
•
Destroy the carton, plastic bag and other packing
materials after the washer is unpacked. Children
might use them for play. Cartons covered with rugs,
bedspreads or plastic sheets can become airtight
chambers.
•
•
Do not put oily or greasy rags or clothing on top of the
washer. These substances give off vapors that could
ignite the materials.
Do not add gasoline, cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
•
•
•
Keep laundry products out of children’s reach. To
prevent personal injury, observe all warnings on
product labels.
Before the washer is removed from service or dis-
carded, remove the washer lid to prevent accidental
entrapment.
•
Under certain conditions, hydrogen gas may be pro-
duced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using the washer, turn on all hot water
faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen
gas. Hydrogen gas is flammable; do not smoke or use
an open flame during this time.
Failure to comply with these warnings could result in
serious personal injuries.
•
•
•
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other
appliance.
Failure to comply with these warnings could result in
fire, explosion, serious bodily injury and/or damage to
the rubber or plastic parts of the washer.
Do not continue to use the washer if you hear squeak-
ing, grinding, rubbing or other unusual noises. This
could be a sign of mechanical breakdown and lead to
fire or serious injury. Contact a qualified technician
immediately.
3
IMPORTANT SAFETY INSTRUCTIONS
PREVENT INJURY
PREVENT INJURY AND DAMAGE TO THE APPLIANCE
•
To prevent shock hazard and assure stability during
operation, the washer must be installed and electrically
grounded by a qualified service person in accordance
with local codes. Installation instructions are packed in
the washer for installer’s reference. Refer to INSTAL-
LATION INSTRUCTIONS for detailed grounding
procedures. If the washer is moved to a new location,
have it checked and reinstalled by a qualified service
person.
To prevent serious personal injury and damage to the
washer:
•
All repairs and servicing must be performed by an
authorized servicer unless specifically recommended
in this Use & Care Guide. Use only authorized factory
parts.
•
•
Do not tamper with controls.
Do not install or store the washer where it will be
exposed to the weather.
•
•
To prevent personal injury or damage to the washer,
the electrical power cord of the washer must be
plugged into a properly grounded and polarized
3-prong outlet. The third grounding prong must never
be removed. Never ground the washer to a gas pipe.
Do not use an extension cord or an adaptor plug.
•
•
•
Do not install on carpet. Install washer on a solid floor.
It may be necessary to reinforce the floor to prevent
vibration or movement.
Do not sit on, step on or stand on the washer. Do not
rest heavy loads on top. The washer is not meant to
support weight.
Follow package directions when using laundry
products. Incorrect usage can produce poisonous gas
- resulting in serious injury or death.
To reduce the risk of electric shock, disconnect this
appliance from the power supply before attempting
any user maintenance. Canceling a cycle or turning
the power off at the console does not disconnect this
appliance from the power supply.
•
•
Do not combine laundry products for use in same load
unless specified on the label.
Do not mix chlorine bleach with ammonia or acids
such as vinegar.
•
To prevent injury, do not reach into the washer while
parts are moving. Before loading, unloading or adding
items, press CANCEL button to stop the cycle. Allow
the wash tub to coast to a complete stop before
reaching inside.
WARNING
FIRE/ELECTRICAL SHOCK HAZARD
Avoid fire hazard or electrical shock. Do not use an
adaptor plug or extension cord or remove grounding
prong from electrical power cord. Failure to follow this
warning can cause serious injury, fire or death.
•
•
This washer is equipped with an electrical overload
protector. The washer motor will stop if it becomes
overheated.
Failure to comply with these warnings could result in
serious personal injuries.
Groundiing type
wall receptacle
WARNING
Do not, under
any circumsttances,
cut, remove,
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with other
household chemicals such as toilet cleaners, rust
removers, acid or products containing ammonia. These
mixtures can produce dangerous fumes which can cause
serious injury or death.
or bypass the
groundiing prong.
Power cord with
3-prong grounded plug
4
OPERATING INSTRUCTIONS
Washing Procedures
• Place delicate and small items such as bras, hosiery
and baby socks in a mesh bag.
WARNING
To reduce the risk of fire, electric shock or injury to
persons, read these IMPORTANT SAFETY INSTRUCTIONS
in this Use and Care Guide before operating your washer.
1
Sort laundry in
can be washed
(Mesh bag not included.)
Pretreat stains and heavy soil.
3
4
• See Stain Removal Guide in this guide for
T
safe, successful stain
removal instruc-
tions.
U
• Sort items
by recom-
mended cycle
and water
Add a measured
temperature.
amount of detergent to the wash tub before
adding the laundry load.
• Separate white, light and colorfast items from dark
and non-colorfast items.
• Separate items that shed lint from items that
attract lint. Casual, synthetic, knit, and corduroy
items will pick up lint from towels, rugs, and
bedspreads.
• Separate heavily soiled items from lightly soiled items.
• Separate lacy, sheer, loosely knit, or delicate items
from durable items.
• Do not machine wash items containing fiberglass.
Small particles of fiberglass left in the drum may
transfer to fabrics in other loads and cause skin
irritation and/or damage to fabrics.
For best results
Use a low-sudsing, high efficiency deter-
gent to prevent oversudsing. Look for this
symbol on the detergent label:
• Follow detergent manufacturer’s directions. The
amount required depends on type of detergent,
load size and soil level, and water hardness.
5
If desired, add liquid bleach to bleach dispenser.
• Before adding the wash load, add liquid bleach to
bleach dispenser located in left front corner under
the lid:
2
Prepare items for washing.
• Empty pockets.
• Brush off lint and dirt. Shake out rugs and beach
towels.
• Close zippers, fasten hooks, button buttons, tie
strings and sashes, and remove non-washable
trims and ornaments.
• Mend rips and tears to prevent further damage
during washing.
• Refer to bleach manufacturer’s directions for
quantity to add.
• Then add 1 cup (240 ml) water to flush the dis-
penser.
• Turn knit items inside out to prevent pilling.
• Do not use powdered bleach in the bleach dispens-
er. Add powdered bleach to the empty tub.
5
OPERATING INSTRUCTIONS
8
Select the appropriate cycle and settings for
the load.
Washing Procedures, continued
• See washer Operating Instructions on following
pages.
6
Add laundry load to washer.
• For best washing performance, dry load level should
not be higher than the upper row of holes in the
wash tub. Do not overload the washer.
9
Start the cycle.
• Close the washer lid. The washer will not operate
with the lid open.
• Turn the cycle selector knob or turn any option
knob to “wake” the washer. You will hear three
beeps to indicate washer is ready to operate.
• After making your selections, press START to
begin the cycle. You will hear one beep.
• To add a forgotten item to the wash tub, press the
pause button to pause the cycle. You will hear two
beeps. Lift the lid and add the item. Close the lid and
press START again, continuing the current cycle.
NOTE
Lifting the lid before the safety lock has engaged during
the final spin will also pause the cycle. After the lid is
lowered, press the START button to resume the cycle.
• Combine large and small items in a load. Load
large items first. Large items should not be more
than half the total wash load.
• When washing a single heavy item, add 1 or 2
towels to balance the load.
• To cancel a running cycle, press the CANCEL
button.
10 Remove items when the cycle is completed.
• For your safety, the lid is locked during the final spin
of the cycle. It will unlock at the cycle end after the
tub has come to a complete stop.
7
If desired, add liquid fabric softener to fabric
softener dispenser.
SAFETY LID LOCK
• Add liquid softener to the dispenser, following fabric
softener label directions. DO NOT use granular
detergent in this dispenser.
• Add water to bring liquid level to fill line on dis-
penser cap.
• DO NOT fill above the maximum fill line.
• Turn fabric softener option on.
• To open the lid during cycle final spin, press the
pause button to pause the cycle. You will hear two
beeps. Wait for the lid lock to release. Do not force
open the locked lid.
• Do not use bleach in this dispenser.
CAUTION
To avoid serious personal injury, do not operate washer
if safety lid lock is missing, damaged or operating
improperly.
NOTE
If a build-up of fabric softener occurs, clean with hot
water. See Care and Cleaning section for additional
information.
• Place washed items in automatic dryer, line dry, or
dry flat as directed by fabric care label. Excess wrin-
kling, color transfer or odors may develop in items
left in the washer after the cycle has ended.
Other Wash Products
• Water conditioner, detergent booster and enzyme
products may be added with the detergent.
For best results
Follow the fabric care label
instructions on items
to be dried.
IMPORTANT
Use of multi-product (detergent plus softener) sheets
or color-absorbing sheets NOT recommended. They
could disable your machine and result in unwarranted
repair costs.
6
OPERATING INSTRUCTIONS
This manual covers many models and not all cycles, options, or features listed are available on every model.
Console shown above for reference only. Your model may differ.
Cycle Selection
Turn the cycle selector in either direction to the cycle
desired.
normal
Use this load for light to normally soiled cottons,
towels, shirts, denims and mixed loads.
For best results
Follow the fabric care label
instructions on items
to be washed.
normal/heavy
Use this cycle for heavily soiled towels, shirts, denims
and mixed loads.
bedding
This cycle is designed for large items such as blankets,
sheets, mattress pads, duvet covers and similar items.
rinse & spin
Select rinse & spin for loads that need a cold water
rinse or to add fabric softener that may have been
omitted in a regular cycle.
Once a cycle is running, turning the selector knob to
another selection will not change the cycle. If cycle
selection change is attempted after the cycle starts, the
indicator lights will flash and a signal will beep, but the
original cycle will continue.
presoak
Use this cycle to soak heavily soiled and stained items
before washing. Any temperature may be selected,
but cold water is recommended with this cycle as
warmer water may set some stains. Use the amount
of detergent recommended for a normal wash cycle. If
desired, use a bleach or a soaking agent safe for the
fabric. The washer will drain at the end of the cycle.
NOTE
To change the cycle selection once the cycle has begun,
press the CANCEL button before selecting a new cycle.
casual
Use this cycle for poly blends with a permanent press
or no-iron finish.
NOTE
Follow presoak with a complete wash cycle suitable for
the load using a half dose of detergent.
delicates
Use this cycle for lightly soiled knits and delicates which
require gentle washing.
heavy duty
Use this cycle for heavily soiled, durable garments - ex.
towels, sports gear, or fabric tote bags. For best soil
and stain removal, use the hottest water safe for the
fabrics being washed.
7
OPERATING INSTRUCTIONS
Cycle Settings
Other Features
Load Size Sensing
For best results
Follow the fabric care label instructions
on items to be washed.
Water level is automatically calculated by the washer.
The washer will perform a dry load sensing procedure
to determine load size before adding water to the tub.
If your model has status lights, the “sensing” indicator
will be lit.
Select appropriate wash water temperature and options
most suitable for each load. Make selections according to
fiber content, colorfastness and soil level.
The settings can be changed before the cycle is started. If
changes are attempted after the cycle starts, the lights will
flash and a signal will beep, but the cycle will continue.
Status Lights
The following indicators may be lighted during the
cycle:
NOTE
To change the temperature once the cycle has begun,
press the pause button, make the new selection and
press START again.
• sensing
• add a garment
• wash
• final spin
• clean
Wash Water Temperature
Turn the temp knob until the desired wash water
temperature is selected. To protect your fabrics, the
temperature range from low to high settings may be
different depending on cycle selected. If an unavailable
temperature setting is selected by the user, the nearest
available temperature will be substituted.
Out of Balance Protection
Your model is equipped with special sensors and
software to prevent machine damage caused by
extreme cases of unbalanced loads at high spin speeds.
In the event that a load is lopsided and weight is
not evenly enough distributed before final spin, the
machine will pause the spinning phase and notify you
of an out of balance situation.
The water heater setting and its distance from the
washer, water usage in other parts of the home, and
seasonally low ground water temperature in some
geographic areas can affect water temperature.
What does the washer do? The washer will stop
spinning, the status indicator lights will blink and an
alarm will beep 3 times quickly every 30 seconds until
the condition is resolved.
hot
Use this setting for heavily soiled white or colorfast
cottons and blends.
What do you do? Lift the washer lid, redistribute the
unbalanced load, close the lid and press START to
resume the final spin of the current cycle.
warm
Use this setting for normally soiled white or colorfast
cottons or blends.
cool
Use this setting for normally soiled sheets, casual items
and washable woolens.
cold
Some warm water will automatically blend with cold tap
supply to achieve cold. Use this setting for lightly soiled
non-colorfast items, knits, delicates, and hand washables.
Cycle Options
fabric softener
If your model is equipped with an automatic fabric
softener dispenser, you must turn the fabric softener
switch to the “on” position for correct operation. See
Care and Cleaning for dispenser cleaning procedures.
8
OPERATING INSTRUCTIONS
Safe Stain Removal Procedures
To reduce the risk of fire or serious injury to persons or
WARNING
HARMFUL VAPOR HAZARD
property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain
removal products.
Do not use or mix liquid chlorine bleach with other
household chemicals such as toilet cleaners, rust
removers, acid or products containing ammonia. These
• Keep stain removal products in their original labeled
containers and out of children’s reach.
mixtures can produce dangerous fumes which can
cause serious injury or death.
• Thoroughly wash any utensils used.
• Do not combine stain removal products, especially
ammonia and chlorine bleach. Dangerous fumes can
result.
• Never wash items which have been previously
cleaned in, washed in, soaked in or spotted with
gasoline, dry cleaning solvents or other flammable
or explosive substances because they give off vapors
that could ignite or explode.
• Never use highly flammable solvents, such as gaso-
line, inside the home. Vapors can explode on contact
with flames or sparks.
For Successful Stain Removal:
• Remove stains promptly.
For best results
Follow the fabric care label instructions
on items to be washed.
• Determine the kind of stain, then follow the recom-
mended treatment in the stain removal chart on the
next page.
• To pretreat stains, use a prewash product, liquid
detergent, or a paste made from powder detergent
and water.
• Use cold water on unknown stains as hot water can
set stains.
• Consult care label instructions for treatments to avoid
on specific fabrics.
• Check for colorfastness by testing stain remover prod-
ucts on an inside seam.
• Rinse and wash items after stain removal.
9
OPERATING INSTRUCTIONS
Stain Removal Suggestions
STAIN
TREATMENT
Adhesive tape, chewing
gum, rubber cement
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with
prewash stain remover or nonflammable dry cleaning fluid.
Baby formula, dairy
products, egg
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more.
Wash.
Beverages (coffee, tea,
soda, juice, alcoholic
beverages)
Pretreat stain. Wash using cold water and bleach safe for fabric.
Blood
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing
enzymes. Wash using bleach safe for fabric.
Candle wax, crayon
Scrape off surface wax. Place stain face down between paper towels. Press with warm
iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain
with prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove
solvent. Wash using bleach safe for fabric.
Chocolate
Pretreat or soak in warm water using product containing enzymes. Wash using bleach
safe for fabric.
Collar or cuff soil,
cosmetics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white
fabric
Use packaged color remover. Wash using bleach safe for fabric.
Grass
Pretreat or soak in warm water using product containing enzymes. Wash using bleach
safe for fabric.
Grease, oil, tar (butter,
fats, salad dressing,
cooking oils, car grease,
motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy
stains and tar, apply nonflammable dry cleaning fluid to back of stain. Replace towels
under stain frequently. Rinse thoroughly. Wash using hottest water safe for fabric.
Ink
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain
remover, denatured alcohol or nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water
before washing. Badly mildewed fabrics may be permanently damaged.
Mud
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Mustard, tomato
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail pol-
ish remover to back of stain. Repeat, replacing paper towels frequently. Do not use on
acetate fabrics.
Paint, varnish
Perspiration
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it
cannot be removed. OIL BASED AND VARNISH: Use solvent recommended on can label.
Rinse thoroughly before washing.
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach
in hottest water safe for fabric.
Rust, brown or yellow
discoloration
Use rust remover safe for fabric. Do not use chlorine bleach because it may intensify
discoloration.
Shoe polish
LIQUID: Pretreat with a paste of powder detergent and water. PASTE: Scrape residue
from fabric. Pretreat with prewash stain remover or nonflammable dry cleaning fluid.
Rinse. Rub detergent into dampened area. Wash using bleach safe for fabric.
Tomato
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Urine, vomit, mucus,
feces
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
Wine
Pretreat or soak in cold water. Wash in hottest water and bleach safe for fabric
10
OPERATING INSTRUCTIONS
Common Washing Problems
Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing
results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
Blue stains
POSSIBLE CAUSES
SOLUTIONS
PREVENTIVE MEASURES
•
Undiluted liquid detergent
or fabric softener dispensed
directly onto fabric.
• If caused by detergent, mix 1 cup (240
ml) white vinegar with 1 quart (.95 L)
water in a plastic container. Soak item 1
hour. Rinse.
•
Add detergent to empty tub. Do
not pour on dry load.
•
Avoid overfilling fabric softener
compartment of dispenser.
•
If caused by fabric softener, rub stains
with bar soap. Wash.
Discoloration,
graying
• Not enough detergent.
• Wash water temperature
too low.
•
•
Rewash with correct amount of deter-
gent and hottest water safe for fabric.
Add bleach safe for fabric.
•
Sort items by soil level and color.
• Use correct amount of detergent,
hottest water and bleach safe
for fabric.
•
Incorrect sorting.
Greasy, oily
stains
• Not enough detergent.
• Treat with prewash stain remover or
liquid detergent.
• Use correct amount of detergent
and hottest water safe for fabric.
Do not pour liquid fabric softener
directly on fabric. See Operating
Your, step 5.
•
Undiluted liquid fabric
softener poured directly on
fabric.
• Increase detergent and water tempera-
ture. Rewash.
•
•
Rub fabric softener stains with bar soap.
Holes, tears, or
snags
• Incorrect use of chlorine
bleach.
•
May be irreversible if rips, tears and
seams cannot be mended.
•
•
Never pour chlorine bleach directly
on fabric.
Check condition of items before
washing. See Operating Your, steps
2 and 5.
•
Unfastened zippers, hooks,
buckles.
•
•
•
Rips, tears and broken threads.
Overloading the washer.
Degradation of fabric.
Lint
•
•
•
Incorrect sorting.
• Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
• See Washing Procedures, steps
1 and 2.
Tissues left in pocket.
Overloading the washer.
•
Do not overload washer.
• Not enough detergent.
•
Add nonprecipitating water conditioner to • Use correct temperature and
•
Undissolved detergent has left
a residue resembling lint.
Static cling is attracting lint.
Load washed too long.
wash water to remove detergent residue.
Add liquid fabric softener to final rinse.
Dry load in dryer.
amount of detergent, water and
wash time.
•
•
•
•
•
Remove lint with lint brush or roller.
Pilling
•
Pilling is normal with synthetic
and permanent press fabrics.
This is due to abrasion from
normal wear.
•
Use a lint brush or shaver to remove
pills.
•
Use fabric softener in the washer
(Fibers ball up
and cling to
fabric.)
to lubricate fibers.
• When ironing, use spray starch or
fabric finish on collars and cuffs.
Turn items inside out to reduce
abrasion.
•
Residue or
powder on dark
items;
•
•
Undissolved detergent.
• Rewash load.
• Increase water temperature using
hottest water safe for fabric.
Some granular detergents
can combine with hard water
minerals to form a residue.
Overloading the washer.
•
•
Do not overload washer.
Stiff, harsh
fabrics.
Use liquid detergent or use
nonprecipitating water conditioner
with powder detergent.
•
•
Wrinkling
Overloading the washer.
• Reduce load size.
•
Do not overload washer.
• Incorrect wash cycle for
wash load.
•
Rinse in cold water with liquid fabric
softener using the casual or delicate
cycle.
• Remove items from washer as
soon as cycle is completed.
•
Use liquid fabric softener.
Yellow buildup
of body soil on
synthetic fabrics
•
Agitation time too short.
• Soak in detergent booster or product
containing enzymes.
•
Select correct wash cycle.
• Wash water temperature
too low.
• Use correct amount of detergent.
• Wash synthetics frequently using
hot or warm water.
•
Wash in hottest water safe for fabric
using casual cycle.
• Not enough detergent.
•
•
Increase detergent.
Add bleach safe for fabric or treat with
color remover.
Yellow or brown
rust stains
• Iron or manganese in water
supply, water pipes, or water
heater.
• To restore discolored load of whites, use
rust remover safe for fabric.
Do not use chlorine bleach to remove
rust stains. It may intensify discolor-
ation.
•
•
Use nonprecipitating water
softener.
•
Before washing, run hot water for
a few minutes to clear lines.
Drain water heater occasionally.
For an ongoing problem, install
an iron filter in your water supply
system.
•
•
11
CARE AND CLEANING
Cleaning Instructions
INSIDE
• Remove items from the washer as soon as the cycle ends. Excess wrin-
kling, color transfer, and odors may develop in items left in the washer.
• Dry the washer top, the area around the lid opening, and the un-
derside of the lid. These areas should always be dry before the lid is
closed.
• Before cleaning the washer interior, unplug the electrical power cord to
avoid electrical shock hazards.
• When extremely soiled items have been washed, a dirty residue may
remain on the tub. Remove this by wiping the tub with a nonabrasive
household cleanser. Rinse thoroughly with water.
• The agitator or tub may become stained from fabric dye. Clean these
parts with a nonabrasive household cleanser. This prevents dye transfer
to future loads.
FABRIC SOFTENER DISPENSER
• Remove the fabric softener dispenser by grasping the dispenser cap
and lifting upward.
• Rinse the cup with a combination of ¾ cup liquid chlorine bleach and
1 gallon hot tap water to remove any buildup. Large amounts of fabric
softener residue may indicate improper dilution or more frequent
cleaning is required. Rinse well with tap water.
• Use a small brush to clean the recesses. Remove all residue.
• Replace the dispenser cup assembly by pressing it firmly into the
agitator.
OUTSIDE
• When washing is completed, wipe top and sides of washer with a damp
cloth. Turn water faucets off to prevent pressure build-up in the hoses.
• Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasive cleansers
• If the cabinet becomes stained, clean with diluted chlorine bleach (1
part bleach to 8 parts water). Rinse several times with clear water.
• Remove glue residue from tape or labels with a mixture of warm water
and mild detergent. Or, touch residue with the sticky side of tape.
• Before moving the washer, place a strip of cardboard or thin fiberboard
under the front leveling legs to prevent damage to the floor.
IMPORTANT
Do not store or place laundry products
on top of washer at any time. They can
damage the finish or controls.
Winterizing Instructions
IMPORTANT
If the washer is stored in an area where freezing can occur
or moved in freezing temperatures, follow these winterizing
instructions to prevent damage to the washer:
1
2
Turn off water supply faucets.
Follow WINTERIZING
INSTRUCTIONS for
cold weather storage
and care.
Disconnect hoses from water supply and drain water from
hoses.
3
4
Plug electrical cord into a properly grounded electrical outlet.
Add 4 gallons (15 L) nontoxic recreational vehicle (RV)
antifreeze to empty wash tub. Close lid.
5
6
Select the rinse & spin cycle. Start the cycle and let the
washer drain for 1 minute to drain out all the water. Not all
of the RV antifreeze will be expelled.
Stop the cycle, unplug electrical power cord, dry off tub
interior and close the lid.
7
8
Store washer in an upright position.
To remove antifreeze from washer after storage, run empty
washer through a complete cycle using detergent. Do not
add wash load.
12
AVOID SERVICE CHECKLIST
Before calling for service, review this list. It may save both time and expense. The list includes common occurrences
that are not the result of defective workmanship or materials in this washer.
OCCURRENCE
NOISE
POSSIBLE CAUSE
SOLUTION
Rattling and clanking
noise.
Foreign objects such as coins or safety pins may be
in tub or pump.
Stop washer and check drum. If noise continues after washer is
restarted, objects may be in pump. Call your authorized servicer.
Belt buckles and metal fasteners are hitting wash
tub.
To prevent unnecessary noise and damage to tub, fasten
fasteners and turn items inside out.
Thumping sound.
Heavy wash loads may produce a thumping sound.
This is usually normal. If sound continues, washer is
probably out of balance.
Stop washer and redistribute wash load.
Squealing sound or hot
rubber odor.
Washer is overloaded.
Do not overload washer. Stop washer and reduce load.
Vibrating noise.
Washer is not resting firmly on floor.
Move washer so it rests firmly on floor. Adjust leveling legs.
See INSTALLATION INSTRUCTIONS for details.
Foam shipping support has not been removed dur-
ing installation.
See INSTALLATION INSTRUCTIONS for removing foam ship-
ping support.
Wash load unevenly distributed in tub.
Stop washer and rearrange wash load.
OPERATING
Washer does not start.
Washer lid is open.
Close washer lid. The washer will not operate when the lid is
open.
Electrical power cord may not be plugged in or con- Make sure plug fits tightly in wall outlet.
nection may be loose.
House fuse blown, circuit breaker tripped, or a
power outage has occurred.
Reset circuit breaker or replace fuse. Do not increase fuse
capacity. If problem is a circuit overload, have it corrected by
a qualified electrician. If problem is a power outage, call local
electric company.
Water supply faucets are not turned on.
Turn on water supply faucets.
Motor is overheated. Washer motor will stop if it
becomes overheated.
Wait for the motor to cool down before attempting to restart.
Washer won’t spin.
Lid is not completely closed.
Close washer lid. The washer will not operate when the lid is
open.
Washer stopped during
Wash load unevenly distributed in tub and out of
Open washer lid, redistribute load. Close lid and press START to
resume final spin.
final spin. Status lights are balance condition has occurred.
blinking and washer beeps
3 times every 30 seconds.
Residue left in drum.
Heavily soiled items.
Wipe tub with a nonabrasive household cleanser, then rinse. Shake
or brush excess dirt and sand from items before washing
WATER
Wash load too wet after
spin.
Washer is overloaded.
Load is out of balance.
Drain hose is kinked.
Washer lid is open.
Do not overload washer. See Washing Procedures.
Rearrange load to allow proper spinning.
Straighten drain hose.
Water does not enter
washer or it enters
slowly.
Close washer lid. The washer will not operate when the lid is
open.
Water supply is not adequate in area.
Check another faucet in the house. Wait until water supply and
pressure increase.
Water supply faucets are not completely open.
Water is being used elsewhere in the house.
Fully open hot and cold faucets.
Water pressure must be at least 10 psi (69 kPa). Avoid running
water elsewhere while washer is filling.
Water inlet hoses are kinked.
Washer is overloaded.
Straighten hoses.
Water level does not
cover load.
Do not overload washer.
Warm or hot water is not Hot water heater is set too low or is a distance
Measure hot water temperature at nearby faucet with candy
or meat thermometer. Water temperature should be at least
120°F (50°C). Adjust water heater as necessary.
hot enough.
from washer.
Hot water is being used elsewhere in the house.
Avoid using hot water elsewhere before or during washer use.
There may not be enough hot water available for proper clean-
ing. If problem persists, your hot water system may be unable
to support more than 1 use at a time.
Water in washer does not Drain hose is kinked or clogged.
drain or drains slowly.
Clean and straighten the drain hose.
Water leaks.
Loose fill hose connection at faucet or washer.
Check and tighten hose connections. Ensure rubber sealing
washers are installed.
House drain pipes are clogged.
Unclog drain pipes. Contact plumber if necessary.
Incorrect wash and rinse
temperatures.
Hot and cold water hoses are connected to wrong
supply faucets.
Connect hot water hose to hot water faucet and cold water
hose to cold water faucet.
Water is entering washer Drain hose standpipe is incorrect height.
but tub does not fill.
Standpipe must be a minimum of 36” (90 cm) high to prevent
siphoning. See INSTALLATION INSTRUCTIONS.
Water is present in tub after Lid lock malfunction.
wash cycle is complete.
Do not bypass lid lock. Call your authorized servicer.
The drain and spin cycles Lid lock malfunction.
did not occur.
Do not bypass lid lock. Call your authorized servicer.
13
MAJOR APPLIANCE WARRANTY INFORMATION
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay
all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such
appliance is installed, used and maintained in accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary
household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a
part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other
cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage
expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux
parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse,
inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT
AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT
NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR
ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE
OTHER RIGHTS THAT VARY FROM STATE TO STATE.
IF YOU NEED SERVICE
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be
required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be
obtained by contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux
authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty
must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are
subject to change without notice.
USA
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
14
|