iLive MP3 Docking Station ITP180B User Manual

USER’S GUIDE  
V:1707-0201-10  
ITP180B  
Bar Speaker with Dock for iPhone/iPod  
For the most up-to-date version of this Users Guide, go to www.ilive.net  
 
FCC Warnings  
NOTE: This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equip-  
ment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or televi-  
sion reception, which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
Additional Warnings  
The apparatus shall not be exposed to dripping or splashing and  
that no objects filled with liquids, such as vases, shall be placed  
on apparatus.  
L’appareil ne doit pas être exposé aux écoulements ou aux écla-  
boussures et aucun objet ne contenant de liquide, tel qu’un vase,  
ne doit être placé sur l’objet.  
Main plug is used as disconnect device and it should remain  
readily operable during intended use. In order to disconnect the  
apparatus from the mains completely, the mains plug should be  
disconnected form the mains socket outlet completely.  
La prise du secteur ne doit pas être obstruée ou doit être facile-  
ment accessible pendant son utilisation. Pour être complètement  
déconnecté de l’alimentation d’entrée, la prise doit être débran-  
chée du secteur.  
Battery shall not be exposed to excessive heat such as sunshine,  
fire or the like.  
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à  
la lumière du soleil, au feu ou autres choses de semblable.  
Caution marking is located at the bottom of the apparatus.  
Les marquages sont inscrits en bas de l’appareil.  
The marking information is located at the bottom of apparatus.  
Les précautions d’emploi sont inscrites en bas de l’appareil.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | ITP180B  
3
 
BAR SPEAKER WITH DOCK FOR IPHONE/IPOD  
Features  
• Works with iPhone  
• Made for iPod  
• Video output  
• Audio/video input  
• 30” length  
• Line input (3.5mm)  
• FM radio  
• Remote control  
• Station memory presets (20 FM)  
• Last channel memory  
• Treble and bass controls  
• 2.1 channel stereo system  
• Preset EQ  
• Subwoofer output  
• Last user setting memory  
• 2 auxiliary audio inputs (RCA)  
• S-video output  
• Basic iPhone/iPod controls  
• Supports Universal docking brackets  
• Wall mountable  
• Digital clock  
• Single alarm  
• Gradual wake  
• Motorized iPod drawer  
• Cloth net speaker grill  
• AC power: built-in AC power cable  
• Wake to iPhone/iPod or radio  
• White LCD display  
• Sleep timer  
Included  
• ITP180B  
• Remote control: requires 2 AAA  
batteries (not included)  
• Docking brackets for iPhone/iPod (6)  
• FM wire antenna  
• Audio/video cable  
• Wall-mount hardware  
4
iLive | ITP180B  
 
TABLE OF CONTENTS  
INTRODUCTION  
6
8
SETUP  
CLOCK, ALARM, AND SLEEP TIMER  
IPHONE/IPOD AND FM RADIO  
9
10  
11  
12  
13  
14  
16  
AUXILIARY INPUT, LINE INPUT AND  
SUBWOOFER OUTPUT  
BASIC CONNECTIVITY  
AV INPUT AND VIDEO INPUT  
MOUNTING TO A WALL  
COMPANY INFORMATION  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | ITP180B  
5
 
INTRODUCTION  
POWER  
Press to turn the  
bar speaker off  
or on.  
POWER  
SOURCE  
Press to switch  
between iPhone/  
iPod, AV, AUX, and  
FM modes.  
SOURCE  
S
LINE IN  
LINE INPUT  
(3.5mm)  
VOLUME  
VOLUME  
Press to adjust the  
volume.  
PLAY/PAUSE  
iPod DRAWER  
PLAY/PAUSE  
Press to play or  
pause a docked  
iPhone or iPod.  
iPod DRAWER  
Press to open or  
close the motor-  
ized dock for  
iPhone/iPod.  
MOTORIZED  
DOCK FOR IPOD  
VIDEO INPUT  
AUXILIARY INPUT  
RESET  
Press using a  
SUBWOOFER  
OUTPUT  
paperclip or like  
object to reset the  
bar speaker to it’s  
default settings.  
FM ANTENNA  
CONNECTION  
S-VIDEO OUTPUT  
VIDEO OUTPUT  
A/V INPUT  
 
STANDBY/ON  
Press to turn the bar  
speaker off or on.  
iPod DRAWER  
Press to open or  
close the motorized  
dock for iPhone/iPod.  
MUTE  
Press to mute the  
volume.  
NUMBER KEYPAD  
REPEAT  
ALARM  
With the power  
off, press to set the  
alarm.  
Press to repeat a  
single track or entire  
album on a docked  
iPhone or iPod.  
CLOCK  
With the power off,  
press to set the clock.  
TREBLE  
With the EQ set to  
FLAT, press to adjust  
the levels of treble.  
SLEEP  
Press repeatedly to  
set the sleep timer.  
MENU UP/DN  
Press to navigate up  
and down in menus  
on a docked iPhone  
or iPod.  
BASS  
With the EQ set to  
FLAT, press to adjust  
the levels of bass.  
SELECT  
Press to make  
selections on a  
docked iPhone or  
iPod.  
REV/FWD/MIN/HR  
Press to rewind or  
fast forward a docked  
iPhone or iPod. Press  
to adjust the hour  
and minute when  
setting the clock or  
alarm.  
SHUFFLE  
Press to play songs  
from a docked  
iPhone or iPod in a  
random order.  
MENU  
Press skip through  
menus on a docked  
iPhone or iPod.  
EQ  
Press to adjust the  
EQ.  
TUN/SKIP  
Press to skip between  
tracks on a docked  
iPhone or iPod. Press  
to tune the radio.  
VOLUME  
Press to adjust the  
volume.  
PLAY/PAUSE  
Press to play or pause  
a docked iPhone or  
iPod.  
ALBUM/CHAPTER/  
PLAYLIST  
Press to skip through  
albums, chapters, or  
playlists on a docked  
iPhone or iPod.  
STOP  
Press to stop a  
docked iPhone or  
iPod during play.  
SOURCE  
Press to switch  
between AV, AUX,  
FM, and iPhone/iPod  
modes.  
MEMORY  
Press to cycle  
through saved radio  
stations.  
iPod  
DISPLAY  
Press to view the  
clock on the display.  
iPod  
Press to switch to  
iPhone/iPod mode.  
MEM  
Press to save a radio  
station to the bar  
speaker’s memory.  
 
SETUP  
Power  
Plug the attached AC cord into a  
standard AC power outlet to power the  
bar speaker.  
Remote  
Requires 2 AAA batteries (not included)  
FM Antenna  
Plug the FM Wire Antenna (included)  
into the FM Antenna Connection.  
8
iLive | ITP180B  
 
CLOCK, ALARM, AND SLEEP TIMER  
Setting the Clock  
Setting the Alarm  
1 Press the POWER button to turn the  
power on.  
1 Press the POWER button to turn the  
power off.  
2 Adjust the volume to the desired  
level.  
2 Press the CLOCK button on the  
remote control.  
3 Press the POWER button to turn the  
power off.  
The time on the display will begin  
blinking.  
4 Press the ALARM button on the  
remote control.  
3 Press the REV/MIN and FWD/HR  
buttons on the remote to adjust the  
minute and hour.  
The alarm time on the display will  
begin blinking.  
4 Wait 5 seconds to finish setting the  
clock.  
5 Press the REV/MIN and FWD/HR  
buttons on the remote to adjust the  
minute and hour.  
Setting the Sleep Timer  
6 Press the SOURCE button on the  
bar speaker to switch to the desired  
alarm source.  
1 Press the POWER button to turn the  
power on.  
2 Press the SOURCE button on the  
bar speaker to switch to the desired  
sleep timer source.  
7 Wait 5 seconds to finish setting the  
alarm.  
ALARM will appear on the display  
when the alarm is set.  
3 Press the SLEEP button repeatedly to  
set the sleep timer.  
8 Press the ALARM button to cancel  
the alarm.  
4 After the set sleep time has expired,  
the bar speaker will automatically  
power off.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | ITP180B  
9
 
IPHONE/IPOD AND FM RADIO  
Docking an iPhone/iPod  
Tuning the FM Radio  
1 Press the POWER button to turn the  
bar speaker on.  
1 Press the POWER button to turn the  
bar speaker on.  
2 Press the SOURCE button to switch  
to iPhone/iPod mode.  
2 Press the SOURCE button to switch  
to FM radio mode.  
3 Press the iPod DRAWER button to  
open the MOTORIZED DOCK FOR  
iPhone/iPod  
4 Locate the numbered bracket that  
fits the iPhone/iPod model that will  
be docked.  
3 Press the TUN/SKIP buttons on the  
remote to tune the FM radio.  
Saving a Radio Station  
1 Follow the instructions for tuning the  
FM radio.  
Each included bracket has a number  
on it, indicating which iPhone/iPod  
model that bracket is compatible with.  
See the separate bracket chart page to  
identify which bracket is needed.  
2 After tuning to the desired station,  
press the MEM button.  
3 Press the MENU UP or MENU DN  
buttons on the remote to select a  
preset.  
5 Snap the bracket into place over  
the iPhone/iPod connector in the  
motorized dock.  
4 Press the MEM button to save the  
current radio station to the selected  
preset.  
6 Connect the iPhone or iPod to  
the connector inside the Dock for  
iPhone/iPod.  
Up to 20 stations can be saved to the  
bar speaker’s memory.  
When the speaker is plugged in, using  
AC power, the docked iPhone or iPod  
will charge.  
Listening to Saved Radio Stations  
1 Press the POWER button to turn the  
bar speaker on.  
Playing an iPhone/iPod  
2 Press the SOURCE button to switch  
to FM radio mode.  
1 Follow the instructions for docking  
an iPhone/iPod.  
3 Press the MEMORY buttons on the  
remote to cycle through saved radio  
stations.  
2 Press the PLAY/PAUSE button to  
begin playing music from the docked  
iPhone or iPod.  
10 iLive | ITP180B  
 
AUXILIARY INPUT, LINE INPUT, AND SUBWOOFER OUTPUT  
Using the Subwoofer Output  
Using the Auxiliary Input  
1 Use an RCA cable (included) to  
connect an external subwoofer to  
the SUBWOOFER OUTPUT.  
1 Connect an RCA cable (included) to  
the AUXILIARY INPUTS on the bar  
speaker and an audio source.  
2 When audio is played through  
any source, the bar speaker will  
automatically use the connected  
subwoofer.  
2 Press the POWER button to turn the  
bar speaker on.  
3 Press the SOURCE button to switch  
to AUX mode.  
The AUXILIARY INPUTS will not work  
when the LINE INPUT is connected.  
4 Use the native controls on the  
connected audio device to  
begin playing music through the  
connected bar speaker.  
Using the Line Input  
1 Connect a 3.5mm line input cable  
(not included) to the LINE INPUT on  
the bar speaker and an audio source.  
2 Press the POWER button to turn the  
bar speaker on.  
3 Press the SOURCE button to switch  
to AUX mode.  
When the LINE INPUT is connected, the  
AUXILIARY INPUTS will not work.  
4 Use the native controls on the  
connected audio device to  
begin playing music through the  
connected bar speaker.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | ITP180B 11  
 
BASIC CONNECTIVITY  
Below, you’ll see a basic flow chart of how you can connect your home  
entertainment devices to the bar speaker, and in turn how the bar speaker connects  
to them.  
AUDIO  
S-VIDEO  
VIDEO  
AUDIO &/Or  
VIDEO  
AUDIO &/Or  
VIDEO  
AUDIO  
DVD PLAYER  
DIGITAL CABLE or SATELLITE TUNER  
GAMING CONSOLE  
VCR  
SUBWOOFER  
12 iLive | ITP180B  
 
AV INPUT AND VIDEO INPUT  
Using the Video Output  
Using the AV Input  
1 Connect an RCA cable (included) to  
the AV INPUTS and an audio source.  
1 Connect an RCA cable (included) to  
the VIDEO OUTPUT and a television.  
2 Press the POWER button to turn the  
bar speaker on.  
2 Adjust the connected television to  
the proper input setting.  
3 Press the SOURCE button to switch  
to AV mode.  
3 Video from a docked iPhone/iPod, or  
a connected DVD player can now be  
played through the bar speaker to  
the connected television.  
4 Use the native controls on the  
connected audio device to  
begin playing music through the  
connected bar speaker.  
Using the S-Video Output  
The S-Video Output will only output  
video from a docked iPod/iPhone.  
Using the Video Input  
1 Connect an RCA cable (included) to  
the VIDEO INPUT and a video source  
(DVD player, Cable or Satellite Tuner,  
Gaming Console, or VCR).  
1 Connect an S-Video cable (not  
included) to the S-VIDEO OUTPUT  
and a television.  
2 Adjust the connected television to  
the proper input setting.  
2 Connect the bar speaker to a  
television using the VIDEO OUTPUT  
or S-VIDEO OUTPUT.  
3 Video from a docked iPhone/iPod  
can now be played through the bar  
speaker to the connected television.  
3 Press the POWER button to turn the  
bar speaker on.  
4 Press the SOURCE button to switch  
to AV mode.  
5 Use the native controls on the  
connected video device to control  
video that runs through the bar  
speaker.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | ITP180B 13  
 
MOUNTING TO A WALL  
Important Notes  
We recommend having this bar speaker  
professionally mounted.  
The included spacers should be used  
at your discretion to extend the face  
of the bar speaker farther from the  
wall. These are typically used when  
mounting the bar speaker under a  
television, and the face of the bar  
speaker needs to be flush with the face  
of the television.  
Required Tools  
Manual or Power Screwdriver  
Stud Finder  
Pencil  
Tape Measure  
Level  
Included Hardware  
(2) Wall Mount Brackets  
(4) Long Screws  
(4) Short Screws  
(2) 1/4Spacers  
(2) 1/2Spacers  
(2) 3/4Spacers  
14 iLive | ITP180B  
 
Getting Started  
studs  
1 Use the Tape Measure to decide  
how high you’d like to hang the bar  
speaker on the wall.  
screws  
spacer  
The bar speaker must be hung within  
6 feet of an AC power outlet for the  
attached AC power cable to reach.  
mounting  
bracket  
2 Use the Stud Finder to locate 2  
parallel wooden studs to screw the  
mounting brackets into.  
16”  
3 Mark the wall at the center of the  
studs using the pencil.  
4 Line the level up on both of your  
marks to make sure they are level.  
If they’re not, adjust the marks as  
needed to make them level.  
ITP180B  
5 After you’ve double checked your  
markings, drill through the top hole  
on both mounting brackets directly  
into the marks you’ve made on the  
wall.  
ITP180B  
6 If you are using the brackets only  
and no spacers, use the included  
short screws. If you are using any of  
the spacers or combination of the  
spacers, use the long screws.  
7 Use the Level to level each of the  
hanging brackets, then drill the  
second screw into the bottom hole  
on both mounting brackets.  
8 Slide the bar speaker onto the  
mounting brackets, and make sure  
there is a firm and stable connection  
before letting go of the bar speaker.  
9 Finally, use the Level to confirm that  
the bar speaker is level.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | ITP180B 15  
 
COMPANY INFORMATION  
International Support  
To download this User’s Guide in English,  
Spanish, or French, visit the support section at  
Para transferir esta guía de usuario en inglés,  
español, o francés, visite la sección de la ayuda en  
Pour télécharger ce guide de l’utilisateur en  
anglais, espagnol, ou français, visitez la section de  
Contact Information  
Address: 2116 Carr Street, St. Louis MO, 63106  
Phone: 1-314-621-2881  
Fax: 1-314-588-1805  
Parts Email: [email protected]  
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are  
subject to change without notice  
 

Graco Baby Swing 1494 User Manual
Haier Flat Panel Television P42V6 A8 User Manual
Hamilton Electronics Microcassette Recorder HA 790 User Manual
Hayter Mowers Lawn Mower 481A User Manual
Healthrider Home Gym HRAW56071 User Manual
Honeywell Clock TE103NL User Manual
Hotpoint Dishwasher HDA3430ZWW User Manual
HP Hewlett Packard DVD Recorder 447328 B21 User Manual
HP Hewlett Packard Network Router 1200s User Manual
Husqvarna Tiller FT900 User Manual