®
IH8 Series
Camera Enclosure
Installation/Operation
Manual C439M - 10/92
5. Only use replacement parts recommended by
Pelco.
1.0 SCOPE
The information contained within this manual covers
the IH8 Series camera enclosure with integral mount.
Please thoroughly familiarize yourself with the infor-
mation in this manual prior to installation and opera-
tion.
1.1 WARNING
To insure safe operation, observe the following guide-
lines:
2.0 DESCRIPTION
The IH8 Series is a light duty camera enclosure with
integralmountdesignedforindooruse. TheIH8Series
can be used with 1/3-inch and 1/2-inch cameras and
will accommodate fixed focal length lenses with or
without auto-iris operation up to 5 inches in length.
1
Installation shall be done by qualified service
and installation personnel.
2. Installation shall be done in accordance with
all local and national electrical and mechani-
cal codes utilizing only approved materials.
This enclosure has a clamshell cover for easy access
when installing or servicing the camera/lens.
Also included in the unique design of this enclosure is
a cable feedthrough hole, a slotted camera bracket, and
an integral mount. The IH8 Series enclosure is con-
structed of .074 ABS plastic and the integral mount is
aluminum.
3. Use only installation methods and materials
capable of supporting four (4) times the maxi-
mum specified load.
4. Unless the unit is specifically marked as a
NEMA Type 3-6P enclosure, it is designed
for Indoor use only and it must not be installed
where exposed to rain and moisture.
PELCO • 300 W. Pontiac Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827 • DataFAX (800) 289-9108 or (559) 292-0435
4.0 INSTALLATION
Note: Fasteners to secure the enclosure to a load-
bearing solid surface are not supplied.
To install the camera/lens, perform the following:
1. Using the mount as a template, mark and drill
holes in the mounting surface. (If you are
planning to conceal the wiring through the
mounting surface you will also need to mark
and drill the cable feedthrough hole at this
time.)Attachtheenclosurewithintegralmount
securely to the mounting surface with fasten-
ers of a suitable size (1/4-20 screws recom-
mended, not supplied).
2. Gentlypullthefrontofthehousingtoseparate
the two halves of the enclosure.
3. Place the camera/lens onto the slotted camera
bracket and secure with the 1/4-20 screw
provided.
4. Route the coax through the cable feedthrough
hole located on the rear of the enclosure.
(If desired,thecoaxcanalsoberoutedthrough
the feedthrough hole on the mount to conceal
the wiring through the mounting surface.)
5. If necessary, shim up the camera/lens using
flat washers (not provided) to ensure the cam-
era/lens is in the center of the viewing win-
dow.
6. Adjust the camera/lens (front to back) so that
the lens is as close to the viewing window as
possible.
7. Replace front cover.
Pelco Manual C439M (10/92)
3
5.0WARRANTY AND RETURN
INFORMATION
RETURNS
In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or (559) 292-1981 to obtain an authoriza-
tion number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be pre-
paid. All merchandise returned for credit may be sub-
ject to a 20% restocking and refurbishing charge.
WARRANTY
PELCO will repair or replace, without charge, any
merchandise proved defective in material or workman-
ship for a period of one year after the date of shipment
(six months on all pan and tilts with auto scan and
medium duty scanners, and two years on Legacy®,
Intercept® and CM9500/CM8500 Matrix products).
PELCO will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. PELCO is not
liable for any incidental or consequential expenses or
liability incurred by the customer as a result of field
repair, installation, or any other reason.
Ship freight prepaid to: PELCO
300 West Pontiac Way
Clovis, CA 93612-5699
The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by PELCO
of the equipment listed herein. PELCO makes no
warrantiesexceptforintendeduseandwillnotbeliable
for any loss, damage, or costs arising, whether conse-
quential or incidental, from the use of said merchan-
dise.
®
PELCO
300 West Pontiac Way
Clovis, CA 93612-5699 USA
This warranty gives you specific legal rights. You may
also have additional rights, which are subject to varia-
tion from state to state.
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
DataFAX (800) 289-9108 or (559) 292-0435
If a warranty repair is required, contact PELCO at
(800) 289-9100 or (559) 292-1981 for a
Repair Authorization number (RA), and provide the
following information:
International customers call 1-559-292-1981 or
FAX 1-559-348-1120
(Product specifications subject to change
without notice.)
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order
number, or PELCO invoice number
3. Details of the defect or problem
C439M
If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.
Ship freight prepaid to: PELCO
300 West Pontiac Way
Clovis, CA 93612-5699
Method of return shipment shall be the same as method
by which the repair item is received by PELCO.
4
Pelco Manual C439M (10/92)
|