Cordialle S120G
Use and Installation Instructions
Note: Ensure that the oven is securely fixed to the
cabinet before use.
This appliance shall be installed in accordance with
the regulations in force and only used in a well
ventilated space.
Read the instructions before installing or using the
appliance and retain them for future use
CONTENTS
Introduction
4
5
6
For Your Safety – Always
For Your Safety – Never
Clock/Minute Minder Operation
Using The Grill
7-8
9
Using the Oven
10-12
13-14
15-17
18-24
25
Oven Cooking Charts
Care and Cleaning
Installation
Something Wrong?
Key Contacts
Back Cover
DISPOSAL OF YOUR PRODUCT
To minimise the risk of injury to children please dispose of your product carefully and
safely. Remove all doors and lids (where fitted). Remove the mains cable (where
fitted) by cutting off flush with the appliance and always ensure that no plug is left in a
condition where it could be connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the
disposal of your product.
3
INTRODUCTION
Your new cooker is guaranteed* and will give lasting service. This guarantee is only applicable if
the appliance has been installed in accordance with the installation instructions detailed in this
booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The cooker is designed specifically for domestic use and responsibility will not be accepted for
use in any other installation.
When first using the cooker ensure that the room is well ventilated (e.g. open a window or use
an extractor fan) and that persons who may be sensitive to the odour avoid any fumes.
It is suggested that any pets be removed from the room until the smell has ceased.
This odour is due to any temporary finish and also any moisture absorbed by the insulation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with the Users Instruction Book.
(b) Has been properly connected to a suitable supply voltage and gas supply as stated on
the Data badge attached to this equipment.
(c) Has not been subjected to misuse or accident or has not been modified or repaired by
any person other than the authorised employee or agent.
(d) Has been correctly installed.
This appliance conforms to the following EEC Directives:
Low Voltage Equipment Gas Appliances
73/23/EEC 90/396/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
4
FOR YOUR SAFETY
When used properly, your appliance is completely safe but as with any
product there are certain precautions that must be observed.
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR
APPLIANCE.
ALWAYS
Always make sure you remove all packaging and literature from inside the oven
and grill compartments before switching on for the first time.
Always make sure you understand the controls prior to using the appliance.
Always keep children away from the appliance when in use as the surfaces will get
extremely hot during and after cooking.
ꢀ
ꢀ
ꢀ
Always make sure all controls are turned off when you have finished cooking and
when not in use.
Always stand back when opening an oven door to allow any build up of steam or
heat to disperse.
Always use dry, good quality oven gloves when removing items from the
oven/grill.
ꢀ
ꢀ
ꢀ
Always take care to avoid heat/steam burns when operating the controls.
Always turn off the electricity supply at the wall switch before cleaning and allow
the appliance to cool.
ꢀ
ꢀ
Always make sure the shelves are in the correct position before switching on the
oven.
ꢀ
Always keep the oven and grill doors closed when the appliance is not in use.
Always take care when removing utensils from the grill when the oven is in use as
the contents may be hot.
ꢀ
ꢀ
Always keep the appliance clean as a build up of grease or fat from cooking can
cause a fire.
Always follow the basic principles of food handling and hygiene to prevent the
possibility of bacterial growth.
ꢀ
ꢀ
Always keep ventilation slots clear of obstructions.
Always refer servicing to a CORGI registered service engineer.
ꢀ
ꢀ
5
FOR YOUR SAFETY
NEVER
Never leave children unsupervised where a cooking appliance is installed as all
ꢀ
cooking surfaces will be hot during and after use.
Never allow anyone to sit or stand on any part of the appliance.
Never store items above the appliance that children may attempt to reach.
Never remove the oven shelves whilst the oven is hot.
Never heat up unopened food containers as pressure can build up causing the
container to burst.
ꢀ
ꢀ
ꢀ
ꢀ
Never store chemicals, food stuffs or pressurised containers in or on the appliance,
or in cabinets immediately above or next to the appliance.
Never use the appliance as a room heater.
Never use the grill to warm plates.
Never dry any items on the oven doors.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Never allow children to play with the controls.
NOTE: The use of a gas cooking appliance results in the production of heat and moisture
in the room in which it is installed. Always Ensure that the kitchen is well ventilated; keep
natural ventilation holes open or install a mechanical ventilation device (mechanical
extractor hood).
In particular, when using the grill or more than one hotplate burner, open a window if a
mechanical ventilation device is not operating.
6
CLOCK/MINUTE MINDER OPERATION
CLOCKFACE
The timer incorporates a 24 hour clock.
0.00
+
-
SYMBOLS
A ‘Bell’ symbol will light up when you select a Minute Minder Period
and will remain lit for the period set.
At the end of the Minute Minder Period, the timer will emit an audible
tone and the ‘Bell’ symbol will disappear.
0.00
Minute
Minder
SETTING THE TIME OF DAY
Step 1
Step 2
Step 3
Step 4
Step 5
Make sure all oven controls are turned off.
0.00
Check the electricity supply to the cooker is turned on.
When switched on, the display will show 0.00
Press and release both buttons simultaneously.
Press the ‘+’ button to set the Time of Day.
The Time of Day can be adjusted, by using the ‘+’ button to
increase the time setting or the ‘-’ button to decrease the
time setting.
0.00
The Time of Day is set if no adjustments are made within 10
seconds.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4 & 5 above.
7
CLOCK/MINUTE MINDER OPERATION
Here you can set a time period of up to 10 hours, that will count down.
When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20
minutes later.
SETTING THE MINUTE MINDER
Step 1
Step 2
Ensure the time of day is set correctly.
Press and release the ‘+’ button.
Note: Step 3 must be started within 10 seconds, otherwise
you must repeat Step 2.
0.00
0.00
Step 3
Press the ‘+’ button to set the required time period.
A ‘Bell’ symbol will light up.
The time period can be adjusted, by using the ‘+’ button to
increase the time period or the ‘-’ button to decrease the
time period.
Release all buttons, the timer display will show the remaining time
period. The ‘Bell’ symbol will remain lit to signify that a time period has
been set.
At the end of the set time an audible tone will be heard and the ‘Bell’
symbol will disappear.
Step 4
To cancel the audible tone press the ‘+’ button.
To cancel the minute minder period press the ‘-’ button until 0.00 is
displayed in the window then press the ‘+’ button.
If at any time the display shows flashing zero’s, it is likely that the
electricity supply has been interrupted.
Reset the timer to the correct time of day.
Note: The Timer display will show the minute minder
period as follows:
Any period up to 99 minutes and 50 seconds -
The display shows MINUTES and SECONDS (10s intervals)
eg. 19 minutes 50 seconds
19.50
1.41
Any period between 100 minutes (1 hour 40 minutes) and up
to 10 hours -
The display shows HOURS and MINUTES
eg. 1 hour 41 minutes
8
USING THE GRILL
CAUTION -
ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS USED.
YOUNG CHILDREN SHOULD BE KEPT AWAY.
Step 1 Open the grill door and remove the grill pan.
Step 2 Push in and turn the control knob anti- clockwise to the large flame symbol.
Sparking will continue until the grill burner is lit.
Step 3 Slide the grill pan along the shelf towards the rear of the compartment until it
stops.
Step 4 Turn the control knob anti-clockwise to the desired setting.
Only turn the control between the large and the small flame symbols.
Step 5 To turn off, turn the control knob fully clockwise to the symbol O.
Note: DO NOT line the grill pan with aluminium foil, as this increases the amount
of fat spitting and can cause a fire.
The grill burner will only operate when the door is open. If the grill door is closed
while the grill is on, the grill burner will be shut off. When the door opened again
the grill burner will turn on and be reignited.
Grilling can be started from cold but for best results preheat for approximately two
minutes. Most cooking is done with the heat on full, but it may be desirable to reduce it
for thicker pieces of meat or for keeping food warm.
For au gratin dishes e.g. macaroni cheese and meringue toppings e.g. baked alaska,
place the dish on the floor of the grill compartment. The base of the grill pan can be
used for warming fruit garnishes on the reduced setting.
COOLING FAN
A gentle flow of air will be blown below the control panel when any control is used.
Whenever the appliance has been used, the cooling fan may continue to run or restart itself
after all the controls have been turned off.
9
USING THE OVEN
Note: DO NOT allow young children near to the appliance when the oven is in use
as the surfaces get hot
The oven has different heat zones - the temperature control settings refer to the
temperature on the middle shelf; above this shelf it is hotter and below it is cooler.
SHELF POSITIONING
The two shelves can be used in four different positions. Each shelf has a safety stop to
prevent it being pulled out too far when attending to food. Shelves are removed from the
oven by pulling them out to the stop and the lifting at the front to withdraw.
OVEN UTENSILS
The baking dish and the grill pan without the handle can be used in the oven. To ensure
good air circulation in the oven, the maximum size of baking tray that should be used is
300mm X 350mm (12" X 14").
OVEN OPERATION
1. Place the shelves in the correct position. ( see cooking chart ).
2. With the oven door closed, push in and turn the control knob fully anti - clockwise.
Sparking will continue until the burner is lit. Turn the control knob clockwise to
the required setting ( see cooking chart ). There is a delay of about one minute
whilst the safety device operates before the burner comes fully on.
3. To turn off, turn the control knob fully clockwise to the symbol O.
Note: The oven burner only operates when the oven door is closed. The oven burner will
shut off when the door is opened, and will turn on and reignite when the door is closed
again.
COOLING FAN
A gentle flow of air will be blown below the control panel when any control is used.
Whenever the appliance has been used, the cooling fan may continue to run or restart itself
after all the controls have been turned off.
10
USING THE OVEN
COLD START COOKING
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be put into a
cold oven. Satisfactory results can also be obtained with creamed mixture, rich pastries or
yeast mixtures, but for perfection we recommend preheating the oven for about 15 minutes
at the gas mark you require for cooking.
ROASTING OF LARGE POULTRY
The maximum weight of poultry that can be accommodated is 11.5kg (25 lbs) of suitable
shape.
It is important to check that the bird DOES NOT overhang the burner at the back of the oven.
STORAGE AND RE-HEATING OF FOOD
It is vitally important to strictly adhere to the basic principles of food handling and hygiene to
prevent the possibility of bacterial growth.
1. If food is to be frozen or not served immediately, cool it in a clean container as quickly as
possible.
2. Completely thaw frozen food in the refrigerator before re-heating.
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven, Mk. 6, and then
serve immediately.
4. Only re-heat food once.
‘COOK CHILL’ DISHES
These should always be placed in a pre-heated oven ideally on the first or second shelf
position. Follow the packet instructions for cooking time.
ALUMINIUM FOIL
If using Aluminium Foil:
1. Remember that it is important to increase the cooking time by one third.
2. Never allow the foil to touch the sides of the oven.
3. Never cover the oven interior with foil.
4. Never cover the oven shelves with foil.
11
USING THE OVEN
The ‘S’ setting on the oven thermostat is used for slow cooking, keeping food warm and
warming plates for short periods.
USING THE ‘S’ SETTING FOR SLOW COOKING
1. All dishes cooked by the ‘S’ setting should be cooked for a minimum 6 hours.
They will ‘hold’ at this setting for a further hour but marked deterioration in
appearance will be noticed in some cases.
2. Joints of meat and poultry should be cooked at Mk. 6 for 30 minutes before turning to
the ‘S’ setting and never be cooked lower than the middle shelf position.
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not be cooked
using the ‘S’ setting.
4. Always stand covered joints on a rack over the meat tin to allow good air circulation.
5. A meat thermometer should be used when cooking pork joints and poultry. The internal
temperature of the food should reach at least 88˚C.
6. This method is unsuitable for stuffed meat and stuffed poultry.
7. Always bring soups, casseroles and liquids to the boil before putting in the oven.
8. Cover casseroles with foil and then the lid to prevent loss of moisture.
9. Always thaw frozen food completely before cooking.
10. Root vegetables will cook better if cut into small pieces.
11. Adjust seasonings and thickenings at the end of the cooking time.
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be cooked
lower in the oven whilst other dishes requiring greater heat can be cooked above them.
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day cooking
sessions, when they can be observed from time to time.
14. Dried red kidney beans must be boiled for a minimum of ten minutes after soaking,
before inclusion in any dish.
12
OVEN COOKING CHART
The following times and setting are for guidance only. When a different setting to that shown
below is given in a recipe, the recipe instructions should be followed. Allow 15 minutes preheat
for best results. Shelf position 1 is the highest.
Gas
Shelf
Food
Mark
Positions
Approx. Cooking Time and Comments
20 - 30 mins, depending on recipe
FISH
Oily and White fish
5
2
MEAT AND POULTRY
Beef
5
5
5
5
5
5
4
3
4
4
4
4
4
4
4
4
25 - 30 mins per 450g (1lb) + 25 mins
40 mins per 450g (1lb) covered in foil plus
40 mins extra uncovered
Ham
Lamb
30 mins per 450g (1lb) + 30 mins
40 mins per 450g (1lb) + 40 mins
25 mins per 450g (1lb) + 25 mins
25 mins per 450g (1lb) + 25 mins
15 - 20 mins per 450g (1lb) + 20 mins
2 - 6 hrs, depending on cut of meat
Pork
Chicken
Duckling & Goose
Turkey
Casseroles
VEGETABLES
Baked jacket potatoes
1
2
5
3
1 / - 3 hrs until soft, depending on size
PUDDINGS
3
4
Milk Puddings (500ml / 1pt)
3
3
4
3
1
6
5
3
3
3
3
3
2
3
1 / - 2 hrs
Baked Custard (500ml / 1pt)
Baked sponge puddings
Baked Apples
40 - 50 mins in Bain-Marie
35 - 50 mins
30 - 40 mins depending on size & type
15 - 20 mins
Meringue puddings
Apple Pie (1 x 205mm / 8")
Fruit crumbles
50 - 60 mins
35 - 40 mins
If using aluminium foil:
1. Remember it is important to increase the cooking time by one third.
2. Do not allow the foil to touch the sides of the oven.
3. Do not cover the oven interior with foil.
4. Do not cover the oven shelves with foil.
13
OVEN COOKING CHART
The following times and settings are for guidance only. Allow 15 minutes preheat for best
results. Shelf position 1 is the highest.
Gas
Mark
Shelf
Positions
Food
Approx. Cooking Time and Comments
CAKES, PASTRIES AND BISCUITS
Small Cakes - 2 trays
- 1 tray
5
5
4
5
2
4
2
2
7
2
4
6
6
6
6
1 & 3
15 - 25 mins.
2
15 - 25 mins.
Victoria sandwich (2 x 205mm / 8")
Swiss Roll
1 & 3
30 - 40 mins.
1
20 - 25 mins.
Christmas cake
Madeira cake
3
3
Time depending on recipe
1
1
4 -
2
1 / 1 / hrs.
Rich Fruit cake
Semi rich fruit cake
Scones
3
Time depending on recipe
1
3
2
4
3
1 / - 1 / hrs.
1 & 3
2
10 - 20 mins.
Shortbread
50 - 70 mins
Biscuits
1 & 3
1 & 3
1 & 3
2
Time depending on recipe
Time depending on recipe
15 - 25 mins.
Shortcrust Pastry
Rich Short Crust Pastry
Flaky/Puff Pastry
Choux Pastry
25 - 35 mins.
2
20 - 30 mins.
YEAST MIXTURES
Bread
7
7
5
3
1 & 3
2
25 - 40 mins
15 - 20 mins
25 - 30 mins
Rolls
Chelsea Buns
MISCELLANEOUS
Yorkshire Pudding
- Large
7
7
2
1
4
30 - 40 mins
- Individual
20 - 25 mins
1
2
Meringues
‘S’
2 / - 4 hrs.
Soft Margarine – If soft tub margarine is used for cake making, use the oven settings
recommended by the margarine manufacturer and not those indicated on the cooking chart.
Temperature settings recommended in this chart refer to cakes made with block margarine or
butter only.
14
CARE AND CLEANING
Warning: Before cleaning, please ensure that the electricity supply to the appliance is switched off and
the appliance is fully cold.
1. “CREDACLEAN” OVEN LINERS - OVEN ONLY
(a) How "Credaclean" works.
The surfaces of the "Credaclean" oven liners are treated
with a special vitreous enamel which absorbs cooking
soils. At temperatures of mark 7 or above, the
special surface enables these soils to be slowly destroyed.
The higher the temperature the more effective it is.
(b) Cleaning.
In most cases normal cooking operations at mark 7
will permit this cleaning operation to proceed
during cooking. However if higher cooking temperatures
are not used regularly, it may be necessary, in order to
prevent heavy soiling, to run the ovens without shelves or
meat pan, at mark 8 for about 2 hours hours. During this
cleaning cycle, surfaces may become hotter than in
normal use. Children should be kept away.
It should not normally be necessary to clean the
"Credaclean" panels with water. If the user feels it is
desirable to do so, wipe them over with a clean, soapy
OVEN SIDE LINERS,
REAR PANEL & ROOF LINER
cloth, followed by a wipe with a clean damp cloth.
DO NOT use biological washing powder, harsh abrasives or
chemical oven cleaners of any kind as this could damage the
“Credaclean” oven liners.
2. CLEANING THE GRILL AND OVEN
(a) Base, Sides & Rear of Grill and Base of Oven.
Wipe out the oven with a damp soapy cloth. For more
stubborn stains on the base of the oven use a well
soaped fine steel wool soap pad.
GRIL
PAN
&
(b) Grill Pan, Meat Pans & Oven Shelves.
OVEN
SHELVE
To prevent stains from being burnt on to the grill pan,
food support and rod shelf, always wash immediately
after use in hot soapy water.
T
OVE
BASE
Use a well soaped fine steel wool soap pad to remove
stubborn stains from the rod shelves, grill pan, meat pan
and the base of the oven.
15
CARE AND CLEANING
3. OVEN DOORS
(a) Control Panel
Regularly wipe with a clean, damp cloth and polish
with a clean, dry cloth.
CONTROL PANEL
(b) Trims
It is advisable to clean the trims regularly to prevent
any build up of soiling which may detract from the
appearance of the cooker. The recommended method of
cleaning is to wipe over the trims with a clean, soft cloth
wrung out in warm water, or mild non abrasive cleaner. (If
in doubt try the cleaner on a small area of trim which is
not notice able in normal use), then after wiping with a
cloth wrung out in clear water, dry with a clean, soft cloth.
OVEN
DOORS
(c) Inner Door Panels & Glass
Open the door fully. The glass panel may now be
washed. Stubborn stains can be removed by using a
well soaped, fine steel wool soap pad.
TRIMS
DO NOT use scouring pads, or abrasive powder, which will
scratch the glass.
4. REPLACEMENT OF THE OVEN LAMP
Warning:
To avoid an electric shock, ensure that the electricity supply
to the appliance is switched off and the appliance is fully
cold before removing lamp lens.
Open the oven door and remove the oven shelves.
Using a thick cloth, grip the lamp lens, unscrew anti-
clockwise and remove the lens.
Carefully unscrew the bulb anti-clockwise. Fit
replacement bulb (25W 300°C SES) and refit lens.
OVEN LAMP
5. HOW TO CLEAN THE LAMP LENS
Warning:
To avoid an electric shock, ensure that the electricity supply
to the appliance is switched off and the appliance is fully
cold before cleaning lamp lens.
Open the oven door and remove the oven shelves.
Using a thick cloth, grip the lamp lens, unscrew anti-
clockwise and remove.
Clean with a non-abrasive cleansing cream and refit
lamp lens.
OVEN LAMP
DO NOT use scouring pads, or abrasive powder, which will
scratch the glass lens
16
CARE AND CLEANING
TO CLEAN THE INSIDE OF OUTER AND INNER GLASS PANELS
Warning: Always switch your appliance OFF at the mains supply and allow to cool before cleaning.
Fig. 1
1. Position oven door as shown in fig. 1.
Note: The door can be wedged open using a towel between
the door and the side trim thus leaving your hands free.
2. Grip inner door panel and handle/outer glass
assembly. Remove two screws and fibre washers
(put to one side) as shown in fig. 2.
3. Pull handle/outer glass assembly at the top
outwards while still holding the inner door panel
and unhook handle/outer glass assembly at the
bottom by lifting handle/outer glass assembly
upwards as shown in fig. 3. Take care not to
dislodge rubber grommets in bottom of door.
Fig. 2
TWO SCREWS/
WASHERS
4. Return the inner door panel to the closed position
as shown in fig. 4.
DOOR
OUTER
DOOR
FIXING
TAG
GLASS &
HANDLE
Warning: Care must be taken when closing the door inner
panel as the door will attempt to snatch shut without the
weight of the handle/outer glass assembly. Avoid trapping
your fingers.
Fig. 3
5. The inside of inner and outer door glass can now
be cleaned using a clean, damp cloth and polished
using a clean, dry cloth.
6. Refit the handle/outer glass assembly by opening
the oven door and hold taking care not to trap your
fingers, see fig. 3. Hook the handle/outer glass
assembly back into the rubber grommets at the
bottom of the inner door panel, see fig. 3.
Fit the handle/outer glass assembly back in
position at the top ensuring the fixing tags on the
handle/outer glass assembly fit inside the door
inner panel. While still holding door together, refit
the two screws and washers, see fig. 2.
DOOR
INNER
PANEL
RUBBER
GROMMETS
Fig. 4
Never operate the ovens without the outer glass panels
correctly refitted.
17
INSTALLATION INSTRUCTIONS
Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure)
and the adjustment conditions are compatible. The adjustment conditions for this appliance are
stated on the data badge which is fitted behind the bottom of the main oven door seal. This
appliance is not designed to be connected to a combustion products evacuation device. It must be
installed and connected in accordance with current installation regulations. particular attention
should be given to the relevant requirements regarding ventilation.
MODEL NUMBER: S120G
2H
Category I (GB. IE)
These models are set to burn NATURAL GAS (G20) at 20 mbar ONLY and can not be used
on any other gas.
GAS SAFETY (INSTALLATION & USE) REGULATIONS
It is the law that all gas appliances are installed by competent persons in accordance with
the current edition of the above regulations. It is in your interest and that of safety to ensure
compliance with the law.
In the UK, CORGI registered installers work to safe standards of practice. The appliance
must also be installed in accordance with BS 6172:. Failure to install the appliance
correctly could invalidate the warranty liability claims and could lead to prosecution.
LOCATION
The appliance may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in
a room containing a bath or shower. The appliance must not be installed in a bed-sitting
room of less than 20m3.
PROVISION FOR VENTILATION
The room containing the appliance should have an air supply in accordance with
BS 5440: Part 2:
The room must have an opening window or equivalent; some rooms may also require a
permanent vent. If the room has a volume between 5 and 10m3, it will require an air vent
of 50cm2 effective area unless it has a door which opens directly to outside. If the room has
a volume of less than 5m3, it will require permanent air vent of 100cm2 effective area.
If there are other fuel burning appliances in the same room, BS 5440: Part 2: should be
consulted to determine air vent requirements.
TECHNICAL DATA
Gas connection
Gas supply
Rp 1/2 (1/2" BSP female)
G20 at 20 mbar.
Pressure test point
Electrical connection
Grill injector
Flexible cord fitted with a 3 pin 13 amp plug.
Z
230 - 240 a.c. 50H 3A fuse
INJECTOR
BURNER
Grill
HEAT INPUT
3.6 kW
150
115
2.4 kW
Oven
18
INSTALLATION INSTRUCTIONS
1. GENERAL
The appliance is designed to be mounted on a floor between two adjacent
cabinets. The cabinets should be securely fixed to the wall and the cooker
securely fixed to the cabinets.
This cooker must not be used free standing.
This appliance must not be installed over any other appliance that generates
heat such as a plinth heater.
The appliance can be installed under a worktop with or without a hob unit above.
It is important that the installation instructions for the hob are strictly observed.
Where a hob is fitted above the oven unit the electrical connection for the hob
0
should be made with an 85 C heat resisting flexible cord to table 15 of BS 6141.
A gas hob fitted above the appliance should be connected to the gas supply with
rigid tubing.
If a hob is to be installed directly above the appliance it must not project
downwards more than 20mm (30mm including a gas supply pipe where
applicable) below the underside of the worktop. Any projection of more than
10mm below the worktop must not project more than 500mm from the wall.
2. FINAL INSTALLATION
a. Ensure that the adjacent cabinets and the gap between them have
dimensions in accordance with the diagram.
b. Assemble the plastic plugs provided into the fixing brackets. (See diagram)
c. Fix the fixing brackets to the sides of the adjacent cabinets so that the centre
line of the brackets are 565mm above the top of the plinth line and the front
face of the plastic plug is level with the front face of the cabinet sides. (See
diagram)
d. Adjust the feet on the cooker to their minimum position, ie. fully screwed in.
e. Slide the cooker centrally into the space between the cabinets ensuring the
following:
i) The gap between the cabinet sides and the cooker is even along
the length of the cabinet sides.
ii) The cable is routed away from any vents in the rear panel and
is not trapped between the cooker and the wall, adjacent cabinets
or under the feet.
f. Adjust the feet using an open ended spanner until the bottom of the cooker
door is in line with the top of the plinth. Using a spirit level check that the
cooker is level in all directions.
g. Check that the plinth can be fitted. If necessary re-adjust the feet and check
that the cooker is level.
h. Open the top oven door and fix the cooker to the brackets through the holes
in the side trims.
i. Fix the plinth in position.
j. Ensure that there is a minimum gap of 1mm between the cooker side trim
and the adjacent cabinet doors or drawer fronts.
19
INSTALLATION
597mm min
720mm min
565mm
150mm min
170mm max
A minimum distance of 25mm should be maintained between the front face of the cabinet
side and the front face of the plinth.
20
INSTALLATION
Top View
Wall
Fixing Bracket
Cooker
70mm
Cabinet Doors
587mm including gas connection but
excluding handle and knobs.
850mm
min
835mm
min
815mm
min
568mm
550mm excluding Gas
connection
Feet adjustable in
height by 40mm.
21
INSTALLATION INSTRUCTIONS
CONNECTING TO GAS SUPPLY
The appliance is designed to be connected with an approved flexible connection to BS 669.
A length of 1.25 to 1.55m is recommended. An adaptor backplate should be fitted in the area
shown to allow the appliance to be pushed fully back into the space between the cabinets. The
flexible hose should be fitted such that it does not pass through a space where it is likely to
become trapped or damaged.
The temperature rise of areas at the rear of the appliance that are likely to come into contact with
the flexible hose do not exceed 70˚C.
140mm
500mm
640mm
460 mm
Dimensions are with the feet
adjusted to their minimum
level.
22
ELECTRICAL CONNECTION
WARNING – THIS APPLIANCE MUST BE EARTHED.
CONNECT TO A 230-240V A.C. SUPPLY ONLY.
Connection to the electricity supply should be made via a properly earthed, readily accessible wall
socket which is adjacent to, and not more than 1.25m away from the appliance and capable of
electrical isolation.
The mains lead should be routed such that it cannot touch hot parts of the appliance i.e. the back
panel above a height of 350mm from the bottom of the oven recess. If the oven is to be wired into a
connector unit, this may be positioned behind the oven providing the following requirements are
met:
i) The connector unit must not project more than 25mm from the wall.
ii) The top of the connector unit must not be more than 350mm above the base of the oven recess.
NOTE: The removed plug cannot be used for any other appliance and should
therefore be properly disposed of and not left where children might find it and plug it into
a supply socket – with the obvious consequent danger.
IF THE FITTED PLUG IS REMOVED
The flexible mains lead must be correctly connected as below to a three pin plug of not less than 13
amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse which is approved
to B.S. 1362.
IMPORTANT: The wires in the mains lead fitted to
this appliance are coloured in
accordance with the following code:
Green &
Yellow to
Earth
Brown to
GREEN AND YELLOW – EARTH
Blue to
Neutral
Live
BLUE
– NEUTRAL
– LIVE
BROWN
3 Amp
Fuse
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:– The wire which is coloured green and yellow must be connected to the terminal
in the plug which is marked with the letter E or by the earth symbol
or coloured green or green
and yellow. The wire which is coloured blue must be connected to the terminal which is marked with
the N or coloured black. The wire which is coloured brown must be connected to the terminal which
is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are
securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the
appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a
qualified electrician and should only be replaced with a flexible cord of the same size i.e. 0.75mm2
cross sectional area and temperature rating of 85˚C e.g. heat resisting PVC.
IF A MOULDED PLUG IS FITTED
In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362 must be
fitted.
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover
the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse
cover can be obtained from your local electrical retailer. The colour of the correct replacement fuse
cover is that of the coloured marks or inserts in the base of the plug.
23
INSTALLATION INSTRUCTIONS
INSTALLATION AND OPERATIONAL CHECKS
After installation, check for gas soundness. The supply pressure can be checked at the
grill injector. Loosen the fastening screw on the left hand side of the grill burner and slide
the burner to the right and then off the injector. Ensure that the grill burner is correctly
located and the fixing screw tightened on reassembly.
1.
2.
Check that the grill burner ignites correctly and burns with a steady flame.
Check for a steady flame on the low setting.
Check that, with the main oven set to mark 9, the burner ignites at low rate, and
then increases to full rate within 60 seconds. Leave the oven full on with the door
closed for 10 minutes, and check that when the control is turned to the ‘S’ setting
that the flame reduces.
3.
Check the operation of the timer, oven light & cooling fan.
Instruct the user on operation of the appliance.
.
24
SOMETHING WRONG?
Before calling a Service Engineer, please check through the following lists.
THERE MAY BE NOTHING WRONG.
Problem
Check
Nothing works.
If the clock display is blank.
Then it is likely that there is no electricity supply to your oven.
Check: (i) That the main cooker wall switch is turned on.
(ii) Check other appliances to see if you have a power cut.
(iii) Check the main circuit breaker for the property.
Draught from beneath control
panel.
A gentle flow of air will be blown from beneath the control panel when
the appliance is used. If the appliance is still warm, this cooling fan may
continue to run, or restart itself after all controls have been turned off.
The fan will stop once the appliance has cooled.
Cooling fan not operating
Oven burner not working
If no air is blown from below the control panel when the controls are
switched on and you have checked through the " Nothing works "
section above, then the cooling fan may be faulty. In this case you should
turn off the appliance and contact your service agent to arrange for a
repair.
Note that the oven burners only operate when the door is closed to
ensure safe operation and avoid wasting heat. With the door closed the
oven burner will ignite.
Oven appears to be cooking at too
high a temperature.
It may be necessary to turn to a lower setting than shown on the cooking
chart or recipe as results depend on personal tastes.
If the oven appears to be cooking at too high a temperature than
previously, and turning down the thermostat has no effect, then the
thermostat may be faulty and you should contact your service agent.
If you have been through the above list and there is still a problem; contact our Service department
(see Key Contacts, back page).
25
NOTES
26
NOTES
27
Key Contacts
Service
Creda has the largest appliance manufacturer’s service team in Europe, trained
specialists directly employed by us to ensure your complete confidence.
Repair Service
UK: 08709 066 066
Republic of Ireland: 1850 302 200
You will be asked for the following information:-
Name, address and postcode.
Telephone number
Model / Serial number of the appliance
Clear and concise details of the query or fault
Place and Date of purchase
(Please keep the receipt as evidence will be required when the engineer calls).
Extended Warranty
To join: UK 08709 088 088
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
Mail Order Hotline
UK: 08709 077 077
Republic of Ireland: (01) 842 6836
For further product information 08701 546474
All Creda Services are offered as an extra benefit and do not affect your statutory rights.
Merloni Elettrodomestici UK Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
September 2003 Part No. 4866200198-01
|